Denver CRP-210 User manual

1. AC POWER CORD
2. FM ANTENNA WIRE
3. SNOOZE BUTTON
4. BATTERY COMPARTMENT
5. CLOCK SETTING SWITCH (RUN / ALM / TIME)
6. POWER SWITCH (ON / AUTO / OFF)
7. LED DISPLAY
8. ROTARY SET DIAL
9. SLEEP BUTTON
10. TUNING CONTROL KNOB
11. AM / FM BAND SELECTION SWITCH
12. VOLUME / BUZZ KNOB
13. PROJECTION
14. PROJECTION ON / OFF
15. MINUTE BUTTON FOR PROJECTION
16. HOUR BUTTON FOR PROJECTION
17. FOCUS FOR BRIGHTNESS ADJUSTMENT
18. TIME SET BUTTON FOR PROJECTION
ENGLISH
12
2
1
14
17
18
8
5
6
11
10
13
15
16
3
7
9
4
Document1 12/16/02 7:23 PM Page 1

POWER CONNECTION
RADIO OPERATION
1.
2.
3.
4.
5.
6.
Set the POWER SWITCH (6) to "ON" position.
Set the AM/FM BAND SELECTION SWITCH (11) to desired waveband.
Tune to the desired station with TUNING CONTROL (10).
Adjust the volume level withVOLUME CONTROL (12).
To obtain better FM reception, lay out the FM ANTENNA WIRE (2) to it's
full extent; or for built-in FM antenna version, uncoil and fully extend AC
POWER CORD (1).
The radio can be switched off by setting POWER SWITCH (6) to the "OFF"
position.
Set the CLOCK SETTING SWITCH (5) to the time set position, and then
rotate the dial to the left (min) or right (hour) hand side to set the current time.
Once the time is set, set the CLOCK SETTING SWITCH (5) to "RUN"
position to stop the 2 flashing dots.
SETTING THE CLOCK TO THE TIME OF DAY
NOTE:
Do not rotate the dial too quickly when you are setting the time, otherwise
the clock radio cannot keep up with your speed and set your desired time
normally.
Set the CLOCK SETTING SWITCH (5) to the alarm set position, and
then rotate the dial to the left (min) or right (hour) hand side to set the
alarm time. Once the time is set, set the CLOCK SETTING SWITCH (5)
to " RUN" position to stop the 2 flashing dots.
SETTING THE ALARM TIME
ALARM RADIO
Set the POWER SWITCH (6) to the AUTO position
Plug the AC POWER CORD (1) to the household outlet. Make sure the voltage
is correct for safety purpose and prevent plausible damages to the set.
Connect one 9 volt battery (not included) to the battery terminals in the
BATTERY COMPARTMENT (4). It maintains the clock continue memory
whenever the AC power is interrupted.
Please note : The display will not exhibit time during power failure but
RADIO:
BUZZER:
Wake to radio. The radio must be tuned on a station and set the
volume to the desired level. The radio will switch on at the
selected alarm time.
Wake to Buzzer. Slide the VOLUME BUZZ KNOB (12) to the
BUZZ position until you hear a "CLICK" sound. The alarm will
switch on at the selected time.
the clock will keep correct time.
Document1 12/16/02 7:23 PM Page 2

SWITCHING OFF THE ALARM
To switch off the alarm, set the POWER SWITCH (6) to the OFF position.
SNOOZE' FUNCTION
The alarm can be interrupted for 9 minutes by pressing SNOOZE BUTTON
(3), after that time the radio or the alarm buzz will sound again.
To preset the HOURS, press simultaneously the HOUR BUTTON (16) and the
TIMEBUTTON(18). Keepthem depresseduntilthe hour digits to be preset are
displayed.
To presetthe MINUTES,press simultaneouslythe MINUTEBUTTON(15)and
theTIMEBUTTON(18),Keepthemdepresseduntiltheminutedigitstobepreset
are displayed.
Focus setting: To adjust the projection clock brightness by turning the focus
(17) until the project's time is clearly shown on the ceiling or wall.
Please note that the Projection (13) will automatically come "On" at the
time you have set the alarm (See Wake To Alarm) regardless of whether
the Projection ON/OFF Switch (14) has been set to "On".
Of course for you to see the time. you must have the Projection elevated
out of its groove in the Clock radio, and adjusted to your required setting
by the focus control (17).
Please note that after you have adiusted the focus control (17) to your required
level of brightness, it will not be possible to push the projection back into
it's groove, as the focus will be protruding.
Therefore please ensure you re-set the focus control (17) back it it's orginal
position, before placing it back into its groove in the clock radio.
TIME SETTING FOR PROJECTION
-
-
-
-
-
NOTE: PROJECTS TIME IMAGE ON THE CEILING OR WALL OF A
DARKENED ROOM.
MAXIMUM PROJECTION DISTANCE IS 3 - 9 FEET
THE LED DIGITAL CLOCK AND THE PROJECTION
CLOCK MUST BE SET SEPARATELY
Document1 12/16/02 7:23 PM Page 3

SPECIFICATIONS
Frequency range : AM 530 - 1600 kHz
FM 88 - 108 MHz
Speaker impedance : 8 ohm
Battery backup : 9V Battery (not included)
(for clock memory)
Power source : 230V ~ 50Hz
"The product shall not be exposed to dripping or
splashing and that no objects filled with liquids, such
as vases, shall be placed on the product."
"The normal ventilation of the product shall not be
impeded for intended use."
Dripping warning :
Ventilation warning :
SLEEP TIMER OPERATION
1.
2.
3.
This clock radio is equipped with a "sleep timer" function which will switch
off the radio automatically after a preselected period from 1 hour 59 minute
to 01 minute.
Press SLEEP BUTTON (9), and then rotate the dial to the left (you desired
time which within 1 hour 59 min) or right (time fixed at 1 hour 59 min) to set
the sleep time.
After preselected "Sleep" time has elapsed, the radio will switch off
automatically. To switch it off before the preselected "Sleep" time has
elapsed, press SNOOZE BUTTON (3).
SLEEP TO RADIO AND WAKE TO RADIO
1.
2.
Set the desired alarm time as described in "SETTING THE ALARM
TIME". Tune the radio on the desired station. Set POWER SWITCH (6)
to "AUTO" position.
Set sleep time as described in SLEEP BUTTON (9) and set the volume.
The radio will switch off after the "sleep" time has elapsed and radio
alarm will switch on next day.
Document1 12/16/02 7:23 PM Page 4