Denver REP V2 VICTORY User manual

Functional Trainer assembly instructions
parts Included:
2 Main Frame Sides
2 Horizontal Back Support Connectors
2 Side Shrouds
1 Pull-up Bar Connector
2 Sets of Weight Supports and Poles
Hardware Included:
Semi-flat washer
x 20
.75 In
Washer
x 4
Screw Cap
x 20
Attach horizontal supports to the back of the frame.
1.
Secure pull up bar between the top of the two uprights.
2.
x16
x16
x16
x16
(1.75 in)
.75 In Bolt
x 12
.5 In Bolt
x 4
1.75 In Bolt
x 20
2 Weight Stacks
2 Cables
1 Back Shroud
2 Weight Pins
Weight Stickers
x4
x4
x4
(1.75 in)
Lock
Washer
x 20
.625 In
Washer
x 20
x4
2.5 In Bolt
x 2
Nut
x 4
1.25 In Bolt
x 4
Follow step by step with our video assembly instructions: https://youtube/wFFwU3MFcB4
or type in- "REP V2 / VICTORY Fitness Functional Trainer Assembly Instructions”
Grab a partner! While it's possible to build with 1 person, we do recommend a helping
hand and the video helps to show this.
VIDEO INSTRUCTIONS
Need more help or missing a part? We are always here for our customers!
Contact us via phone: [phone] or e-mail at inf[email protected]om or via Facebook/Instagram
Any issues? Please contact us directly by phone: [phone], email: [email protected]om or
morse code...(.-. . .--. ..-. .. - -. . … …). We are always here for our Customers! - Team REP. Denver, Colorado
Denver, CO(720) 420-1731

x4
x2
x2
3. Take the pre-assembled screws o of the
rails in order to slide on the adjustable
pulleys.
Push rails into place on each upright. Replace the
pre-assemebled screw that was taken o to ensure
the pulley stays in place. Secure the rails by screwing
in appropriate hardware.
Remove brackets from each side of frame.
4.
5.
6. Set up weight supports and insert rods to prepare
for weight stacks.
7.
Slide weight plates onto poles with plastic washer side
facing upward. There should be 18 plates plus the
head pin plate on each side. Secure weight stack and
poles by reattaching brackets at the top of the pole.
x4
x4
(1.25 in)
(.75 in)
(.75 in)
(.625 in)
(.625 in)
(2.5 in)
Denver, CO
Any issues? Please contact us directly by phone: [phone], email: [email protected]om or
morse code...(.-. . .--. ..-. .. - -. . … …). We are always here for our Customers! - Team REP. Denver, Colorado

8. Run cable through pulleys. Begin by taking lock nut o
of threaded bolt end, and feed the cable through the
adjustable pulley. Secure it with the lock nut and
additional nut from hardware pack! Attach carabiner
to cable by feeding cable through ball, rubber stopper,
then caribiner.
9.
Attach side and back shrouds using bolts specified.
10. Weight pin, plate stickers, bolt caps
x16
(.75 in)
(.75 in)
x4
x16
(.625 in)
x12
(.5 in)
(.5 in)
+
+
1.
2.
3.
4.
5. 6.
7.
Start*
Any issues? Please contact us directly by phone: [phone], email: [email protected]om or
morse code...(.-. . .--. ..-. .. - -. . … …). We are always here for our Customers! - Team REP. Denver, Colorado