Desa C26TO Instruction manual

If any wood pieces are missing or damaged, contact the
dealer where you purchased this mantel for replacement. If
hardware is missing or damaged, contact DESAHeating, LLC
at 1-866-672-6040 for referral information. You can also visit
DESA Heating, LLC’s web site at www.desatech.com.
       




IMPORTANT: If you are staining an unnished mantel (C26TU
only), remove any sawdust, dirt or oils. This will prevent blem-
ishes from appearing under the stain. Stain mantel before
assembling according to manufacturer’s instructions. Apply
sanding sealer.
IMPORTANT: If you are painting an unnished mantel (C26TU
only), assemble mantel before painting. Follow directions
listed on paint for wood products. Apply base coat and top
coat following directions listed on product.
Note: Gather all mantel pieces together before assembling
mantel.
     /4   
     
are used for this purpose.
C26TU and C26TO
Corner Mantel and Base
ASSEMBLY AND INSTALLATION INSTRUCTIONS
IMPORTANT:


-

This mantel kit contains the following:
• Mantel pieces - unassembled and numbered as follows:
#1 Base
#2 Right Side Assembly
#3 Left Side Assembly
#4 Header
#5 Top
#6 Top Triangle
#7 Top Left Support
#8 Top Right Support
#9 Top Center Support
#10 Base Support
#11 Vertical Support
Right Top Trim Strip
Left Top Trim Strip
• Hardware Package
22 - 1 1/4" Wood Screws 114325-01
8 - 1" Finishing Nails 114295-04
4 - 2" Wood Screws 122447-01
* Extra hardware may be included
Tools required:
• Power Screwdriver with #2 Phillips Bit
• Hammer
• Nail Set
www.desatech.com

123672-01A
2www.desatech.com
Header #4
Header
Assembly
Block
Figure 1 - Installing Base Support
Figure 2 - Installing Header
Base #1
11/4" Screws
Base Support #10
11/4"
Screws
Left Leg
Assembly #3
Right Leg
Assembly #2
Figure 3 - Installing Mantel Base
11/4"
Screws

IMPORTANT:


Use the following illustrations to assemble mantel. Use only
screws provided.
IMPORTANT: Align mantel left to right on base before installing.
Corner of mantel legs must be ush with back of mantel base
before installation. Use a tape measure to insure accuracy.
Right Leg
Assembly
#2
Left Leg
Assembly #3
Base #1
Header into
Groove on
Legs

www.desatech.com
123672-01A 3
Fireplace Installation
1. Fireplace should be fully assembled. See Assembling
Fireplace in replace owner’s manual.
2. Mantel must be installed ush with two walls. Remove
baseboard along walls where mantel is to be installed.
Baseboard will prevent proper installation of mantel and
base.
3. Place mantel base close to installation location. See re-
place owner’s manual for installation clearances. Leave
enough room to insert replace from back of mantel.
4. If installing gas replace, install gas line. See Connecting
to Gas Supply in replace owner’s manual. Remember to
leave access to gas shutoff valve somewhere on mantel
base or where it is accessible to user. Check for leaks. See
Checking Gas Connections in replace owner’s manual.
5. Position replace inside mantel through back opening
(see Figure 5). Carefully position gas lines if applicable.
IMPORTANT: Use caution when positioning replace on
base. Base may scratch easily. Make sure replace is in
proper position within mantel opening before continuing
with installation.
6.      Lower bottom louver
door. Use two screws provided in replace hardware kit
and attach replace to wooden base. Close louver door.
 Before installing logs
or burner assembly (see owner’s manual) remove screws
securing oor to assembly. Lift oor for access to bot-
tom of replace. Use two screws provided in replace
hardware kit and attach replace base to wooden base.
Reinstall oor with screws removed previously.
Figure 5 - Installing Gas Fireplace
Mantel Top
Assembly
Assembly
Blocks
Assembly
Blocks
11/4"
Screws
Mantel
Legs Flush
with Mantel
Base
Figure 4 - Installing Mantel Top
Corner
of Mantel
Legs Must
be Flush
with Edge
of Mantel
Top
IMPORTANT: Use 2" screws only on top center support. Using
2" screws in any other location will damage mantel.
IMPORTANT: Align mantel top left to right before installing.
Back corner of mantel leg must be ush with edge of mantel
top before installation.
IMPORTANT: If installing a gas replace, vertical support
will be installed to mantel assembly after gas replace has
been installed. If installing electric replace, rst install verti-
cal support and install replace from front of mantel. Do not
put any weight on mantel top until vertical support has been
installed.


This mantel can be used with DESA Heating, LLC electric
replaces. Electric replaces install from the front of mantel.
To install electric replace see replace instruction manual.

Install vertical support (see Figure 6).
Figure 7 - Installing Mantel Trim
Finishing Nails
Trim Strips
123672-01
Rev. A
07/08
Figure 6 - Installing Vertical Support
Vertical
Support
#11
1 1/4" Screws
1 1/4" Screws
Base Support #10
Top
Center
Support

1. Carefully push mantel and base into position in corner
and ush against both walls. Check operation of replace
before proceeding.
2. Place right trim strip on right side of top and left trim on left
side of top. Align both pieces so any gaps between mantel
and wall are covered as well as possible and front of trim
strips are ush with side of top. With one person holding
trim strips in place, nail each strip to mantle using nishing
nails included in hardware kit and nail set.
123672 01
NOT A UPC
DESA Heating, LLC
2701 Industrial Drive
Bowling Green, KY 42101
www.desatech.com
1-866-672-6040