Diamond SY200/DV-R6 User manual

Mod: SY200/DV-R6
Production code: GV38-200-I
06/2018

Model:
VK/CW
1
102-070730
UKUK Content
13
13
13
13
14
15
16
16
41
44
45
46
Important safety instructions
Unpacking and installation
Electrical connection
Start-up of the cabinet
Thermostat
Maintenance and cleaning
Service
Disposal
Dimensions
Technical data
Electrical circuit diagramme
Refriger systemation
Table of parameters 47

UK
Important safety instructions
1. To obtain full use of the cabinet, we recommend reading this instruction manual.
2. It is the user’s responsibility to operate the appliance in accordance with the instructions
given.
3. Contact your dealer immediately in case of any malfunctions.
4. Place the cabinet in a dry and ventilated place.
5. Keep the cabinet away from strongly heat-emitting sources and do not expose it to direct
sunlight.
6. Always keep in mind that all electrical devices are sources of potential danger.
7. Do not store inflammable material such as thinner, gasoline etc. in the cabinet.
8. We declare that no asbestos nor any CFC are used in the construction.
9. The oil in the compressor does not contain PCB.
Unpacking and installation
Remove the wooden pallet and the packing. External surfaces are supplied with a protection foil,
which must be removed before installation
Electrical connecting
The cabinet operates on 230 V/50 Hz.
The wall socket should be easily accessible.
All earthing requirements stipulated by the local electricity authorities must be observed. The
cabinet plug and wall socket should then give correct earthing. If in doubt, contact your local
supplier or authorized electrician.
The flexible cord fitted to this appliance has three cores for use with a 3-pin 13-Amp or 3-pin 15-
Amp plug. If a B.S. 1363 (13-Amp) fused plug is used, it should be fitted with a 13-Amp fuse.
The wires in this mains lead are coloured in accordance with the following code:
Green/Yellow: Earth, Blue: Neutral, Brown: Live.
The main electrical connections must be done by skilled electricians.
Start-up of the cabinet
Before use, we recommend that the cabinet is cleaned, see the section on maintenance and cleaning.
Important !
If the cabinet has been vertically placed during transport, please wait 2 hours before starting up the
cabinet.
Connect the cabinet to a socket and turn on the switch on the control panel, see fig. 1.9.
13

Fig. 1.9
Thermostat
The thermostat is placed in the control panel, see fig. 2.0.
Fig. 2.0
DP2 DP1
The thermostat has been pre-set and in most cases it is not necessary to adjust the settings.
When turning on the cabinet the display will show the current temperature in the cabinet.
Indications LED’s:
DP1: Flashing, indicates that a parameter is being changed
Switched on, indicates that the compressor is activated
DP2: Switched on, indicates that defrosting is activated.
Keyboard lock:
+ To lock or unlock the keyboard, press these keys simultaneously for about 5 seconds
(to lock the display reads ’Pof’, to unlock the display reads ’Pon’).
Display set temperature:
Press this key and the display will show the set temperature. Press the key again to return to
normal reading
14

Set new temperature:
Press this key and the display shows the set temperature.
Press this key to increase the set temperature.
Press this key to lower the set temperature.
Press this key to save the new settings. The display will flash with the new value and will
then return to normal reading.
Changing of parameters:
Press this key continuously for 5 seconds to access the list of parameters. The display will
show the number of the parameter and after 2 seconds the value.
Press this key to increase the value.
Press this key to lower the value.
Press this key to save the new settings. The display will flash with the new value and will
then return to normal reading.
See table of parameters from page 47.
Alarm codes:
PF1 Flashing in the display: indicates that the cabinet sensor is defective.
The cabinet will strive to keep the set temperature until it has been repaired.
Maintenance and cleaning
Switch the cooler off at the socket.
The cabinet must be periodically cleaned. Clean the external and internal surfaces of the cabinet
with a light soap solution and subsequently wipe dry. External surfaces can be maintained using
steel oil.
Do NOT use cleansers containing chlorine or other harsh cleansers, as these can damage the
stainless steel surfaces and the internal cooling system.
Clean the condenser and the compressor compartment using a vacuum cleaner and a stiff brush.
Do NOT hose the compressor compartment with water as this can cause short circuits and damage
on the electrical parts.
15

Service
The cooling system is a hermetically sealed system and does not require supervision, only cleaning.
If the cabinet fails to cool, check if the reason is a power cut.
If you cannot locate the reason to the failure of the cabinet, please contact your supplier. Please
inform model and serial number of the cabinet. You can find this information on the rating label
which is placed inside the cabinet in the top right hand side.
Disposal
Disposal of the cabinet must take place in an environmentally correct way. Please note existing
regulation on disposal. There may be special requirements and conditions which must be observed.
16

41

42

43

Technical data
Model Volume
Litres
Dimensions
HxWxD
mm.
Temperature
ºC
Weight
nett
Kgs.
Voltage
V.
Wattage
W.
Energy
Consumption
Kwh/24h
VK33-120 435x1200x335
4
+2/[phone] 2,8
VK33-150 435x1500x335 +2/[phone] 2,8
VK33-160 435x1600x335 +2/[phone] 2,8
VK33-180 435x1800x335 +2/[phone] 2,8
VK33-200 435x2000x335 +2/[phone] 2,8
VK38-120 435x1200x395 +2/[phone] 2,8
VK38-150 435x1500x395 +2/[phone] 2,8
VK38-160 435x1600x395 +2/[phone] 2,8
VK38-180 435x1800x395 +2/[phone] 2,8
VK38-200 435x2000x395 +2/[phone] 4,2
44

45

46 46

47
REK31E
Parameter Description REK31
d1 Main Set point 2 ºC
d2 Differential ( hysteresis ) 3 ºC
d3 lower limit of main set point 2 ºC
d4 Upper limit of main set point 10 ºC
d5 Minimum time interval between the disactivation and successive activation on compressor 99sec.
d6 Max temperature alarm differential 50 ºC
d7 Maximum or minimum temperature alarm delay 0
d8 Time interval between defrost cycle 6h
d9 Max defrost cycle time 20min
d12 Real temperature display delay at defrost end 30 min
d14 Dripping time 1min
d19 Offset ? -4 ºC
d22 Unit of measure, 0=C, 1=F 0
d23 Compressor function during o probe failure 2
d24 Compressor on-time during probe failure 10 min
d25 Compressor off-time during by probe failure 10 min
d38 Minimum temperature alarm differential 40 ºC