Diamond WCB/38-B User manual

Mod: WCB/38-B
Production code: TFW375- BLACK
08/2017

Model:
TFW 365-2 / TFW 365-2S
TFW 375 / TFW375S
1
700-110103

UK Contents
Important safety instructions 12
Unpacking and installation 12
Electrical connections 13
Start-up of the cabinet 13
Lock 13
Operation TFW 365-2 14
Operation TFW 375 15
Internal light 15
Water tray 16
Carbon filter 16
Changing position of shelves 16
Door reversal 17
Maintenance and cleaning 18
Service 18
Disposal 18
2

UK
Important safety instructions
1. To obtain full use of the cabinet, we recommend reading this instruction manual.
2. It is the user’s responsibility to operate the appliance in accordance with the instructions
given.
3. Contact your dealer immediately in case of any malfunctions.
4. Place the cabinet in a dry and ventilated place.
5. Keep the cabinet away from strongly heat-emitting sources and do not expose it to direct
sunlight.
6. Always keep in mind that all electrical devices are sources of potential danger.
7. Do not store inflammable material such as thinner, gasoline etc. in the cabinet.
8. We declare that no asbestos nor any CFC are used in the construction.
9. The oil in the compressor does not contain PCB.
Unpacking and installation
Remove the wooden pallet and the packing.
To ensure correct function it is important that the cabinet is level. The cabinet is supplied with legs,
which can be adjusted. See fig. 1.1.
Fig. 1.1
If you want to build in your cabinet please note the following:
1. There must be at least 10 cm free space above the cabinet in order for the cooling system to
work satisfactorily.
2. There must be sufficient space at the hinge side to clean and replace the shelves and clean
around the hinge.
12

Electrical connecting
The cabinet operates on 230 V/50 Hz.
The wall socket should be easily accessible.
All earthing requirements stipulated by the local electricity authorities must be observed. The
cabinet plug and wall socket should then give correct earthing. If in doubt, contact your local
supplier or authorized electrician.
The flexible cord fitted to this appliance has three cores for use with a 3-pin 13-Amp or 3-pin 15-
Amp plug. If a B.S. 1363 (13-Amp) fused plug is used, it should be fitted with a 13-Amp fuse.
The wires in this mains lead are coloured in accordance with the following code:
Green/Yellow: Earth, Blue: Neutral, Brown: Live.
The main electrical connections must be done by skilled electricians.
Start-up of the cabinet
Before use, we recommend that the cabinet is cleaned, see the section on maintenance and cleaning.
Important !
If the cabinet has been horizontally placed during transport, please wait 2 hours before starting up
the cabinet.
In order to ensure optimum function of the cabinet the ambient temperature must be between 18 and
35 ºC.
Lock
The cabinet is provided with a lock, which is placed in the bottom panel, see fig. 1.2.
Fig. 1.2
13

Operation model TFW 365-2
Connect the cabinet to a socket and turn on the switch on the control panel (POWER), see fig. 1.9.
Fig. 1.9
When the cabinet is turned on, the display will show the current temperatures in the cabinet’s two
chambers.
Control lamp ”Run” will turn on.
Display set temperature:
Press this key and the display will flash the set temperature for the upper chamber.
After 5 seconds the thermostat will return to normal reading.
Press this key and the display will flash the set temperature for the lower chamber.
After 5 seconds the thermostat will return to normal reading.
Set new temperature:
Press this key and the display will flash the set temperature.
Every subsequent press on this key will lower the setting by 1 ºC, from 12 ºC to 5 ºC and
will start over again after that.
When the required temperature is reached, wait for 5 seconds and the thermostat will
return to normal reading.
Press this key and the display will flash the set temperature.
Every subsequent press on this key will lower the setting by 1 ºC, from 18 ºC to 12 ºC
and will start over again after that.
When the required temperature is reached, wait for 5 seconds and the thermostat will
return to normal reading.
Display temperature in ºC/ºF:
+
Press these keys simultaneously for 5 seconds and display of temperature will
change between Fahrenheit and Celsius.
14

Operation model TFW 375
Connect the cabinet to a socket and turn on the switch on the control panel (POWER), see fig. 2.0.
Fig. 2.0
When the cabinet is turned on, the display will show the current temperature in the cabinet.
Set new temperature:
Press this key and the set temperature will increase by 1°C for each pressure.
Press this key and the set temperature will decrease by 1ºC for each pressure.
Display temperature in ºC/ºF:
+
Press these keys simultaneously for 5 seconds and display of temperature will
change between Fahrenheit and Celsius.
Internal light:
Press this key to turn on/off the internal light.
15

Water tray
In order to prevent drying up of the wine corks due to low humidity the cabinet is supplied with a
water tray, which should be placed at the top shelf, see fig. 1.3.
Fig. 1.3
Carbon filter
The cabinet is supplied with a carbon filter to prevent bad smell. This is placed at the rear wall
inside the cabinet, see fig. 1.4.
Fig. 1.4
Changing position of shelves
Remove both stop blocks which are mounted with a cross-point screw. Then pull out the shelf, see
fig. 2.2.
Fig. 2.2
16

Door reversal
Open the door, remove the two screws in the bottom hinge and lift out the door, see fig. 2.4.
Fig. 2.4
Move the the top hinge to the opposite side, see fig. 2.5.
Fig. 2.5
Move the bottom hinge to the opposite side, see fig. 2.6.
Fig. 2.6
Replace the door on the bottom hinge and mount the screws again, see fig. 2.7.
Fig. 2.7
17

Maintenance and cleaning
Switch the cooler off at the socket.
The cabinet must be periodically cleaned. Clean the external and internal surfaces of the cabinet
with a light soap solution and subsequently wipe dry. External surfaces can be maintained using
steel oil.
Keep the fan cover clean by using a vacuum cleaner and a stiff brush.
Do NOT use cleansers containing chlorine or other harsh cleansers, as these can damage the
stainless steel surfaces and the internal cooling system.
Do NOT hose the compressor compartment with water as this can cause short circuits and damage
on the electrical parts.
Service
The cooling system is a hermetically sealed system and does not require supervision, only cleaning.
If the cabinet fails to cool, check if the reason is a power cut.
If you cannot locate the reason to the failure of the cabinet, please contact your supplier. Please
inform model and serial number of the cabinet. You can find this information on the rating label
which is placed on the back side of the cabinet on the left hand side.
Disposal
Disposal of the cabinet must take place in an environmentally correct way. Please note existing
regulation on disposal. There may be special requirements and conditions which must be observed.
18