die-schaukel.de Education User manual

DINEN1176 PatentsDE10259377/EP1575683
Rev. 06/2012 Use at your own risk – We do not accept responsibility for accidents © 2012 die-schaukel.de
1. General Preparations
Use only mountings with joints and suitable approval certification (e.g., Marathon). This also
applies to swings and rockers. In the case of municipal facilities or commercial use, observe
the general swing directives as well as Norm EN 1176. Check equipment regularly for
damage and make sure it is firmly anchored in the ground.
2. Assembly
We recommend two points of suspension, each with a double anchoring.
Observe the minimum lifting capacity of 6kN.
The outdoor suspension of the swing frame requires through-hole mounting. In the case of
wooden beam assembly, make sure you have a stable carrier beam (minimum thickness
12x14 cm); carrier screws must not stick out from the upper surface!
Hook assembly is only permitted in the case of private use. Exchange every one to two
years due to overload danger. Make sure the hooks are in the correct position.
3. Operation and maintenance
Inspection and approval of the correct positioning and tightness of all parts may be done
only by adult. Check and service at regular intervals and make sure that all screw
connections are screwed in tightly on all of the sections!
Warning: Do not jump on the bent frame parts or place extreme or one-sided loads on it.
This can lead to material stress and breakage.
4. Aligning the lying surface
Always hang up the swing at both rings.
All settings are made with rope shortenings at each rope.
Pushing the rope shortening upwards lengthens the rope,
Pulling the rope shortening downwards shortens the rope.
For alignment the lying surface must be unloaded.
The height adjustment is carried out by 4 rope shortenings.
The horizontal adjustment is carried out with 2 rope shortenings.
The final alignment is carried out with one rope shortening.
When shortening or lengthening the swing ropes, make sure that the ropes are always
the same length. Unequal rope lengths cause circular pendulum motions.
5. Strapping in babies and infants
Children under the age of 3 may only use the swing under the supervision of an adult. For
safety reasons, safety belts are obligatory for babies and infants.
6. Care and cleaning
For outdoors we recommend taking down the swing during frost or extended periods of rain,
in order to maintain the functionality of the high-quality impact protection.
Protect from frost!
The webbing can be washed in its entirety or in individual stripes. We recommend hand or
machine-washing up to 100 F or 40° Celsius. To clean or disinfect the impact protection, a
soft, soapy cloth should preferably be used. Do not use any abrasive cleaning materials,
steam-jet degreasers or similar.
Colour and technical changes reserved.
We wish you lots of fun, play and happiness, your Schaukel Team
Assembly instructions and manual for
multi-child swings Education and Challenger
Congratulations on your purchase of a multi-child swing from die-schaukel.de, which is certified
and complies with DIN EN 1176. To ensure safe operation, please observe the following
guidelines:
Nominal load-bearing capacity of 330 lbs. or 150 kg
Suspension height between 6 – 9 ft. or 1.80 - 2.80 m
7 ft. or 2 m (in front and behind)
Distance to stationery parts (e.g. swing frame) min. 30 in or 80 cm
Distance to swinging parts (e.g. neighbouring swing) min. 27 in or 70 cm
Distance of swing corners to the floor min. 15 in or 40 cm
Best distance of suspension points is swing with + 4-8 in. (10-20 cm) beyond.
No objects should be in the swing area and the ground must be free of
obstacles, hindrances, ledges, steps or similar
Construction
First check that the delivered parts are complete and then follow the steps shown
A. 2 x short impact protection (headpiece) C. 2 x long impact protection (side piece)
B. 2 x short aluminium tube D. 2 x long aluminium tube
E. 1 x large plastic pouch with lying surface netting:
E1: short straps
E2: long straps
Minimum number of straps: Size M (Medium): 21 short and 9 long straps
Size L (Large): 27 short and 11 long straps
F. Ropeset Pro
G. 1 x small plastic pouch: 4 x screws, 4 x conical distance rings,
2 x hexagonal wrench
AA
BD
C
E
FG
B
Marathon
Français
EspañolItaliano Deutsch
English
Nederlands
Art.Nr. 1960802

die-schaukel.de GmbH & Co KG, 81475 München, Deutschland [email protected]
Rev 06/2012 Use at your own risk – We do not accept responsibility for accidents Assembly instructions and manual for type of swings „Education and Challenger“
3 x Threading
Short bands E1 onto 2 x long tubes D
Long bands E2 onto 1 x short tube B
Bolting
Turn screws and distance rings
1+2 tightly or 15 Nm
(with Hexagonal pin spanner)
Attention: Do not pinch
the straps!
Weaving
First thread long straps 1+3+5+…as a bundle
Thread rest of bands in push-pull
Bolting
Turn screws and distance rings
3+4 tightly or 15 Nm
(with Hexagonal pin spanner)
Attention: Do not pinch
the straps!
Threading & Insert
Long bands E2 onto short tube B
Putting & Locking
Put in short pipe into head piece A,
Put in long pipes into head piece A
and lock
Putting & Locking
Put head simultaneously
onto long tubes Side pieces C
Carefully plug and bend
With
Marathon:
Non-ring
mounting
option
Other suspensions:
Suspend using ring from rope set,
mount ring in swing direction
Rope‐Set
Unscrew and secure