Digi Opengear OPERATIONS MANAGER 2200 User manual

QUICK START GUIDE
OPERATIONS MANAGER 2200
Includes:
OM2216, OM2216-L, OM2224-24E, OM2224-24E-L, OM2224-24E-10G,
OM2224-24E-10G-L, OM2232, OM2232-L, OM2248, OM2248-L, OM2248-10G,
OM2248-10G-L, DDC
23.03 Mar 2023

REGISTER
This Quick Start Guide covers basic installation and configuration of the OM2200. For detailed guidance,
consult the Operations Manager User Guide: https://opengear.com/support/documentation/.
Register your product: https://opengear.com/product-registration
When you register, you:
lActivate your warranty.
lGet notified when firmware updates are released: https://opengear.com/support/device-updates/
WHAT'S IN THE BOX
OM2200 Device
Figure: OM2248-L model
1. Serial ports i
2. RJ45 serial console
3. Front USBports
4. NET1 andNET2 (1GSFP and Copper) ii
5. LEDindicators iii
6. USB serial console
7. Config erase button
8. SIMcard slots iv
9. Cell (main) iv
10. Cell (aux) iv
11. GPS iv v
12. USBserial ports
13. Dual ACpower supply vi
i. Number of serial ports varies per model. Integrated switch variation on next page.
ii. Combination network interfaces allow either SFPor Copper to be used. 10Gvariation on next page.
iii. LED definitions available in the Operations ManagerUser Guide.
iv. Cellular models only.
v. Not implemented.
vi. DualDC variation on next page.
2

Device Variations
Integrated Switch
OM2224-24Emodels have 24 serial ports (left) and 24 gigabit ethernet ports (right).
10GEthernet
10Gmodels have network interfaces NET1 (10G SFP+), NET2 (10GSFP+) and NET3 (1GCopper).
DualDCPower Supply (DDC)
DDCmodels have a dual DCpower supply.
3

Kit Contents
Note: Contents may be different from those pictured due to region or supplier.
Label Item Quantity Notes
OM2200 device 1
1 IECpower cables or DDC terminals (optional) 2 Region-specific
2 Rack mount screw kit 1
3 OM2200 rack ears 2
4Cisco straight pinout RJ45 to DB9F crossover serial
adapter 1 Part number 319015
5 CAT5e RJ45 UTPstraight cable - 5ft/1.5m 1 Part number 440016
6 4GLTE-APro Antennas 2 Part number 469042
Cellular models only
Table: List of contents
4

HARDWARE INSTALLATION
Step 1. Connect Network Interfaces
Connect the device to a local network using any of the available physical network interfaces. All interfaces
will receive a dynamic address via DHCPand DHCPv6.
Figure: Network interfaces for 1GbEthernet models Figure: Network interfaces for 10Gb Ethernet models
Additionally, the device can be accessed from a computer or local network via a static IPv4 address as
shown in Table: Default static interface connection.
Model Interface Static Address
1GbEthernet NET1 192.168.0.1/24
10GbEthernet NET3 192.168.0.1/24
Table: Default static interface connection
Firewall Zone Network Interfaces
WAN , NET3
LAN NET2
Table: Default firewall zones for interfaces
Step 2. Connect Cellular Antennas
For -L models, attach the included antennas or external mount to the CELL (MAIN) and CELL (AUX)
connectors.
If you have a data plan, insert a carrier-provided mini-SIM into the first SIMcardslot (slot 1) with contacts
facing upward.
Note: You will hear a click when it is correctly inserted.
5

Step 3. Connect Serial Devices
Connect managed devices to the serial interfaces on the front of the unit.
Step 4. Connect USB Devices
USBserial devices can be connected to the USBslots at the front and rear of the unit if required.
Note: The front USBslots are USB 3.0 and the rear USBslots are USB 2.0.
Step 5. Connect The Power
AC
DDC
Figure: Dual power supply connectors for OM2200
AC only: Connect the power cable to the rear of the unit.
A second power cable can be connected if redundancy is
required. The power cables can be connected in any
order.
OR
DDC option: Connect the DDC terminals to the DC power
cable (not supplied) and plug the DDC terminals into the
rear of the unit.
LEDPowerStatus Indicator
Figure: Power supply has redundancy Figure: Power supply does not have redundancy
6

ACCESS THE DEVICE
Step 1. Log in via the Web UI
Using a computer on the same subnet as the static network interface shown in "Hardware Installation" on
page5, access the web UI with your web browser at https://192.168.0.1/ .
Note: The device has a self-signed SSLcertificate. Your browser will display an "Untrusted
connection"warning. Click through the warning to access the login page.
To log in for the first time, enter the username root and password default and click Submit.
Step 2. Change Root Password
When logging in to the device for the first time you will be prompted to change the root password
immediately.
Enter the current password followed by the new password and click Log in.
The ACCESS > Serial Ports page appears displaying a list of connected serial devices and links to a
Web Terminal or SSH connection for each.
CONFIGURE SNMPPOWER ALERTS
Configure > SNMP Alerts > Power > Voltage
Configure the System Voltage Range alert to send an SNMPTRAPwhenever the system reboots or the
voltage on either power supply leaves or enters the user-configured voltage range.
For more details, consult the Operations Manager User Guide:
https://opengear.com/support/documentation/.
7

CONFIGURE SERIAL PORTS
To change settings for individual serial ports:
1. Navigate to CONFIGURE >Serial Ports.
2. Click the Edit button next to the port you wish to modify.
3. Change port settings, logging settings or configure IP aliases.
4. Click Apply to save changes.
Field Value
Mode ConsoleServer
Pinout X2
Baud Rate 9600
Data Bits 8
Parity None
Stop Bits 1
Table: Default configuration for serial ports
8

CONFIGURE LOCAL CONSOLE
CONFIGURE>Local Management Consoles
Operations Manager OM2200 units contain one RJ45 serial console and one micro-USB serial console.
Console Manager CM8100-10G units contain one RJ45 serial console.
To configure local console ports:
1. Navigate to CONFIGURE > Local Management Consoles.
2. Click the Edit button next to the local console you wish to modify.
3. Change port settings.
4. Click Apply to save changes.
Field Value
Baud Rate 115200
Data Bits 8
Parity None
Stop Bits 1
Emulation VT102
Table: Default serial port configuration for local console access
9

CONFIGURE NETWORK
CONFIGURE >Network Connections >Network Interfaces
Click to expand any row to display status information about the interface and its connections.
10

Configure Physical Interfaces
Click the Edit button to configure media and MTU for the any of the physical interfaces.
Modify Default IPv4 Static Interface
1. Click the "IPv4 Static" label under NET1 or NET3 NET3 to open the edit connection page.
2. Enter the IPv4 address.
3. Enter the network mask.
4. Click Apply to save changes.
Configure Cellular Interface
If your unit has a cellular modem it will appear in the list of Network Interfaces. It is disabled by default and
requires configuration.
Step 1. Enable Cellular Interface
Click the Enabled button to enable the cellular interface.
11

Tip: Before enabling the modem please follow the steps under "Hardware Installation" on page5 to
ensure good signal strength.
Step 2. Enter Carrier APNSettings
If your carrier requires an APN it must be entered before a successful cellular connection can be
established.
1. Click the Edit button to open the Manage Cellular Interface page.
2. Expand the SIMSettings section under SIM CARD1.
3. Enter the APNsettings for your carrier.
4. Click Confirm to save the changes.
12

View Switch Port Interfaces
OM2224-24E models have an integrated Ethernet switch. The switch ports are bridged together by default
in the interface called "Switch".
This default bridge can be modified or deleted to configure custom bridges or bonds between any
interface.
For more details, consult the Operations Manager User Guide:
https://opengear.com/support/documentation/.
13

CREATE NEW ADMINISTRATIVE USER
Note: You should create a new administrative user rather than continuing as the root user.
1. Navigate to CONFIGURE>User Management >Local Users.
2. Click the Add User button at the top-right of the page.
3. Click the User Enabled checkbox.
4. Enter Username and Password.
5. Assign the admin group to the user to provide full access privileges.
6. Click Save User to create the new user account.
7. Log out and log back in as this user for all administrative functions.
For more details about Users and Groups configuration, consult the Operations Manager User Guide:
https://opengear.com/support/documentation/.
14

ACCESS DEVICE CONSOLES
After you have attached managed devices and configured serial ports by following "Configure Serial
Ports" on page8, you can now access the console of your managed devices on your network.
Web UI
1. Navigate to ACCESS >Serial Ports to view the list of serial ports on the device.
2. Click the Web Terminal button to the right of any serial port in Console Server mode to access it
via the web terminal.
Console
For administrator users logged in to the device via console or SSH:
1. Type pmshell to view the list of available managed devices.
2. Enter the port number to access the desired device and press Enter.
SSH
The managed devices connected to the Operations Manager can be accessed directly with an SSH
command to connect to the device.
lTo view the list of managed devices: ssh <username>+serial@<device address>
lTo connect to a specific device by port:ssh <username>+port<number>@<device address>
lTo connect to a specific device by name:ssh <username>+<port label>@<device address>
Note: The SSHdelimiter can be modified via the Web UIat CONFIGURE>Services >SSH.
Telnet
Telnet access to managed devices is not supported at this time.
15

LIGHTHOUSE CENTRALIZED MANAGEMENT
Note: Lighthouse is a powerful tool that simplifies the way you manage your out-of-band network
through a single pane of glass. Better control and visibility provides 24/7 resilient access to your
connected ITinfrastructure. For more information, visit https://opengear.com/products/lighthouse/.
To enroll your device:
1. Navigate to CONFIGURE >Lighthouse Enrollment.
2. Click the Add Lighthouse Enrollment button at the top-right of the page.
3. Enter the Lighthouse Address, Enrollment Token, optional port and optional Enrollment Bundle.
4. Click Apply to begin the enrollment process.
Note: Enrollment of an Opengear device can also be performed from Lighthouse using AddNode
functionality.
16