Digimerge DCV23DL User manual

Product Information
User Manuals
Quick Start Guides
Specificatio Sheets
Software Upgrades
Firmware Upgrades
VISIT
www.digimerge.com
Digimerge Technologies Inc.
Copyright © 2011 Digimerge Technologies Inc.
As our products are subject to continuous improvement,
Digimerge reserves the right to modify product design,
specifications and prices, without notice and without
incurring any obligation. E&OE
IT’S ALL ON THE WEB!
Camera Specifications
ULTRA RESOLUTION
IR DOME CAMERA
Specfications:
1/3" Sony Super HAD™ II
Video Output
Horizontal Resolution
FOV (Horizontal)
Termination
Lens Focal Length / Type
S/N Ratio
Power Consumption
NTSC: 768 (H) x 494 (V)
600 TVL
74 degrees
Video: BNC Female
3.6mm F2.0 / Fixed
> 50dB (AGC off)
Internal; 2:1 Interlace
50ft (15m); 14 LED's
250mA max
Operating Temp. -4°F ~ 122°F
Comp. 1.0 Vpp @ 75ohm
Iris & Shutter Speed AES; 1/60 ~ 1/100,000 sec.
Power Requirement
Dimensions
Minimum Illumination
Video Format / Pixels
0.2 LUX @ F2.0 (IR Off)
0 LUX (IR LEDs ON)
0.4kg / 0.8lbs
Height: 88mm / 3.5”
Diameter: 95mm / 3.8”
Weight
Sync. & Scan. Systems
IR Range
Image Sensor
12V DC ±10%
Dimensions:
95mm / 3.8”
88mm / 3.5”
MODEL: DCV23DL
English Version 1.0
QUICK START GUIDE
Copyright ©2011 Digimerge Technology Inc.
www.digimerge.com

1. Connect the BNC connector of the camera to the
video cable.
2. DC Power—
Power adapto r: Connect a 12V DC
Power Adaptor (not included) to the camera. Plug
the Power Adaptor into a local power outlet.
•DCPower—
Power Pigtail (not included):
Connect a Power Pigtail to the camera. Connect
the terminating wires of the cable directly to the
DC power source.
NOTE: The Power Pigtail is a non-polarity input.You can connect the
wires to either the positive or negative ports of the DC power source.
Contents Installing the camera
1 x Weatherproof IR Dome
Camera
1. Rotate the camera base counter clockwise to
separate it from the ball camera and dome cover.
2. Mount the camera base to the wall or ceiling using
the included screws.
3. Feed the BNC/power termination cable through
the camera base. Connect video and power cable
as described in next section 'Setting up the
camera'.
4. Position the dome cover over the camera and
screw it clockwise half way onto the camera base.
5. Move the ball camera to the desired position and
while holding it firmly in place, screw the dome
cover firmly in place so it does not move during
process of securing dome cover to camera base
Camera Base
Features
• Sony Super HAD™ II / 600TVL
• Advanced Digital Noise Reduction (DNR)*
• 50 ft (15m) IR Night Vision Range**
•3.6mmWideAngleLens
• IP67 Weatherproof rating***
• 3-Axis Design for Wall/Ceiling Mounting
• 12V DC Operation
*Default Setting
** IR Illumination range under ideal conditions. Objects at or beyond this
range may be partially or completely obscured, depending on the camera
application.
*** Not recommended for submersion in water
WARNING - A REGULATED UL/CSA APPROVED 12V DC power supply
is REQUIRED for use with this camera. Use of a non-regulated, non-
conforming power supply can damage this product and will void the
warranty.
4 x Mounting screws
Setting up the camera
ATTENTION - Test the camera prior to selecting a permanent
mounting location by temporarily connecting the cameras and
cables to the DVR or Observation System.
PRECAUTIONS
• Use an appropriate low voltage power cable to prevent fire or
electrical shock.
• Make sure to install the camera in an area that can support the
camera weight.
• There are no user serviceable parts inside the camera. Please
do not disassemble the camera.
• Do not clean the lens cover with an abbrasive cleaning material
Please use a soft cloth to clean the lens cover.