Digisol DG-GS4110 User manual

V1.0
2020-01-22
DG-GS4110
PORTS
8
8 PORT L2 GIGABIT ETHERNET WEB MANAGED
SWITCH WITH 2 GIGABIT SFP PORTS

Trademarks:
Copyright
Copyright 2020 by DIGISOL SYSTEMS LTD. All rights reserved.
Company has an on-going policy of upgrading its products and it may be
possible that information in this document is not up-to-date.
Please check with your local distributors for the latest information.
No part of this document can be copied or reproduced in any form without
written consent from the company.
TM
DIGISOL is a trademark of DIGISOL SYSTEMS LTD. All other trademarks
are the property of the respective manufacturers.

About guide:
This guide provides instructions to install the Switch.
Note: The model you have purchased may appear slightly different from the illustrations shown
in the document. Refer to the Product Instruction and Technical Specification sections for
detailed information about your switch, its components, network connections, and technical
specifications.
Terminology / Usage:
In this guide, the term "Switch" (first letter capitalized) refers to the Switch, and "switch" (first
letter lower case) refers to other Ethernet switches. Some technologies refer to terms
"switch", "bridge" and "switching hubs" interchangeably, and both are commonly accepted for
Ethernet switches.
Note: indicates important information that helps a better use of the device.
Warning: indicates potential property damage or personal injury.
Products introduction
Thanks for purchasing the Web Managed Ethernet Switch products.
The is a Web Managed Gigabit Ethernet Switch, It provides 8 10/100/1000Mbps Auto-
Negotiation RJ45 ports and 2 Gigabit SFP Ports . It supports the port's full line speed forwarding to
ensure the stable transmission of data. This switch can be used as a small and medium-sized LAN
network.
Excellent performance can help you widely use in wireless, monitoring and other fields.
8 Port 10/100/1000Base-TX with 2 Gigabit SFP Web Managed Switch

Hardware installation
Front Panel
PWR LED：The Power LED lights up when the Switch is connected to a power source.
Link/Act LED: The Link/Act LED flashes which indicate a network link through the corresponding
port. Blinking indicates that the Switch is either sending or receiving data to the port.
RST: Pressing the Reset button for 5 seconds the switch will change back to the default
Configuration and all changes will be lost.
Rear Panel
Grounding: use specialized ground lead connect.
Connect the power adapter output terminal to this port. Supports input voltages +44 ~ +57 VDC
This chapter provides unpacking and installation information for the Web Managed Ethernet
switch.
First step: open a seal
Open the shipping carton and carefully unpack its contents. Please consult the packing list
located in the User Manual to make sure all items are present and not damaged.
Switch 1pcs
AC power cord 1pcs
Rubber feet 4pcs
Screws 6pcs
Mounting brackets 2pcs
CD 1pcs
If any item is found missing or damaged, please contact the local reseller for replacement.
Second step: switch installation
For safe switch installation and operation, it is recommended that you:
Visually inspect the power cord to see that it is secured fully to the AC power connector.
Make sure that there is proper heat dissipation and adequate ventilation around the switch.
Do not place heavy objects on the switch.

Desktop or Shelf Installation
When installing the switch on a desktop or shelf, the rubber feet included with the device must be
attached on the bottom at each corner of the device's base. Allow enough ventilation space
between the device and the objects around it.
Rack Installation
Attach the mounting brackets to the switch's side panels (one on each side) and secure them with
the screws provided (please note that these brackets are not designed for palm size switches).
Third step: Plugging in the AC Power Cord
Using the AC power cord to connect to the power adapter, and then plug the output terminal of
the adapter into the DC IN socket on the back of the switch. (The AC power outlet should be
grounded)
Warning: Do not turn on the power switch before power cables are connected. Power surge may
cause damage to the Switch.

Power failure
As a precaution, the switch should be unplugged in case of power failure. When power is resumed,
plug the switch back in.
Getting Started
This chapter introduces the management interface of Web Managed Ethernet switch.
Management Option
The Web Managed Ethernet switch can be managed through any port on the device by using the
Web-based management.
Each switch must be assigned its own IP address, which is used for communication with Web-
Based Management or a SNMP network manager. The PC should have an IP address in the same
range as the switch.
Please refer to the following installation instructions for the Web-based Management.
Using Web-based Management
After a successful physical installation, you can configure the Switch, monitor the network status,
and display statistics using a web browser.
Supported Web Browsers
The embedded Web-based Management currently supports the following web browsers:
Internet Explorer 6 or higher version
Netscape 8 or higher version
Mozilla
Firefox 1.5/2.0 or higher version
Connecting to the Switch
You will need the following equipment to begin the web configuration of your device:
1. A PC with a RJ-45 Ethernet connection
2. A standard Ethernet cable
Connect the Ethernet cable to any of the ports on the front panel of the switch and to the
Ethernet port on the PC.

Login Web-based Management
In order to login and configure the switch via an Ethernet connection, the PC must have an IP
address in the same subnet as the switch. For example, if the switch has an IP address of
192.168.0.1, the PC should have an IP address of 192.168.0.x (where x is a number between 2 ~
254), and a subnet mask of 255.255.255.0
Open the web browser and enter 192.168.0.1 (the factory-default IP address) in the address bar.
Then press <Enter>.
Enter the IP address in the web browser
NOTE: The switch's factory default IP address is 192.168.0.1 with a subnet mask of
When the following logon dialog box appears, enter the password then click OK.
By default, the username is admin and the password is admin.
To log in to the switch, the IP address of your PC should be set in the same subnet as that of the
switch. The IP address is 192.168.0.x (”x” is any number from 2 to 254). Subnet Mask is
255.255.255.0. 255.255.255.0

1. WEB page elements
Shown in Figure 2, WEB page is mainly composed of three parts: title page, navigation tree page
and main page
Title page is used to display the logo
Main page Is used to display the user from the navigation tree, select the page
Logon Dialog Box