Digital Watchdog DWC-B5661TIR User manual

06252014
ABOUT MANUAL
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
Starlight MPA Bullet Camera
DWC-B5661TIR
DWC-B5661TIR550

2
PRECAUTIONS
Do not open or modify.
Do not open the case except during maintenance and installation,
for it may be dangerous and can cause damages.
Do not put objects into the unit.
Keep metal objects and flammable substances from entering the camera.
It can cause fire, short-circuits, or other damages.
Be careful when handling the unit.
To prevent damages, do not drop the camera or subject it to shock or vibration.
Do not install near electric or magnetic fields.
Protect from humidity and dust.
Protect from high temperature.
Be careful when installing near the ceiling of a kitchen or a boiler room,
as the temperature may rise to high levels.
Cleaning:
To remove dirt from the case, moisten a soft cloth wi h a soft detergent solution and wipe.
Mounting Surface:
The material of the mounting surface must be strong enough to support the camera.
FCC COMPLIANCE
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference, when the equipment is operated in a residen ial environment. This
equipment generates, uses, and radiates radio frequency energy; and if it is not installed and used in
accordance with the instruction manual, it may cause harmful interference to radio communications.
WARNING: Changes or modifications are not expressly approved by the manufacturer.

3
TABLE OF CONTENTS
Introduction
Installation
Module OSD Menu
Troubleshooting
Warranty Information
Specifications
Features
Parts and Descriptions
Dimensions
Inside the Box
Mount Installation Instructions
Connecting to Monitors
Control Board
4
5
6-7
8
9
10
11
12
13-25
26
27-28
29-30
Adjus ing the Camera Angle

4
FEATURES*
1/3" Sony 1.3M CMOS
820 TV Lines [B/W], 800 TV Lines [Color]
2.8~12mm Varifocal Auto Iris Lens [DWC-B5661TIR Model]
5~50mm Varifocal Auto Iris Lens [DWC-B5661TIR550 Model]
100ft Range IR with Intelligent Camera Sync, Smart IR [DWC-B5661TIR Model]
150ft Range IR with Intelligent Camera Sync, Smart IR [DWC-B5661TIR550 Model]
True Day & Night with IR Cut Filter
3D DNR (3D Digital Noise Reduction)
WDR (Wide Dynamic Range)
Star-Light (Super Low Light Technology)
HME (Highlight Masking Exposure)
Defog (Extreme Weather Image Compensation)
Digital Quick Zoom & 8x Digital Zoom
16:9 and 4:3 Viewing Modes
AGC / BLC / AWB
Privacy Zones (16) & 4 Motion Detection Zones
Camera Control via RS-485/ UTC
Secondary BNC Output
RS485, UTP, & 1Alarm Output Built-In
IP66 Certified (Weatherproof)

5
PARTS & DESCRIPTION*
1Moun ing Bracket
Camera Module
Sunshield Adjusting Screws
Sunshield Cover
IR Module
Front Case
2
3
4
512
11
10
9
8
7
6
5
43
1
2
6
OSD Joystick Controller
BNC Cable
12VDC Power Outlet
RS485 Cable
UTP Cable
Alarm Output Cable
7
8
9
10
12 11

6
DIMENSIONS IN MILLIMETERS (IN)*
DWC-B5661TIR
224.5
(8.83”)
206.0
(8.11”)
94.0
(3.7”)
96.7 (3.8”)
78.0 (3.07”)
4.2 (0.16”)

7
DIMENSIONS IN MILLIMETERS (IN)*
DWC-B5661TIR550
252.0
(9.9”)
222.5
(8.76”)
93.5
(3.68”)
96.7 (3.8”)
78.0 (3.07”)
4.2 (0.16”)

8
INSIDE THE BOX*
Included with Bullet Camera:
1
2
3
4
6
5
User Manual
Moun ing Template
4 Machine Screws and 4 Dry Wall Anchors
Secondary Video-BNC Cable
L-Key
DC Plug Power Cable
0 0
AB U MA A
B
B
Starlight MPA Bullet Camera
DWC-B566 T R
DWC-B566 T R550
6

9
INSTALLATION INSTRUCTIONS*
1. Using the mounting template or your own camera,
mark and drill the necessary holes to mount he
bracket to a wall or ceiling.
2. Pull all necessary wires through and make the
proper connections.
3. Use the four (4) mounting screws to install
the camera on the wall or ceiling.
NPT 3/4” Pipe
*Installation Using a Junction Box
*Note: Electrical junction box and
required screws sold separately.

Use the diagram below to connect to a Monitor or CRT Monitor properly.
12VDC/24VAC
Monitor
CCTV Monitor
Second Video Output
Right
Left
Up
Down
Power Connection - 12VDC/24VAC Dual Voltage (Auto Polarity Detection and Protection)
All cameras are equipped with a second video output for on-site configuration.
10
CONNECTING TO MONITORS*

11
Joystick: Controls the OSD menu.
Secondary Connector:
Video Output Connector for
On-Site Configuration
CONTROL BOARD*
Remove the camera’s lens cover by rotating it counter-clockwise.
Use the Joystick to control the camera’s OSD options.
1
2

CAUTION :
12
ADJUSTING THE CAMERA ANGLE*
Do not rotate more than 360o.
Do not unnecessarily twist too many times.
1
2

13
MODULE OSD MENU*
LENS
BACKLIGHT
AGC
0 ~ 20
DRC
OFF / LOW / MIDDLE / HIGH
DEFOG
STARLIGHT
3D DNR
EXIT JUMP
EXPOSURE
PRIVACY SETUP
COLOR FUNCTION
MOTION
WB BAL. D&N MODE
CONTROL
SMART IR
0 ~ 20
EXT LED
AUTO / OFF
B&W BURST
OFF / ON
DELAY
ZONE NUM.MOTION
SHARPNESS
0 ~ 10
GAMMA
0.45 ~ 0.65
M RROR
D-ZOOM
x1.0 ~ x8.0
FL P
EXIT JUMP
SAVE & EXIT
EXIT
COMMUNICA.
CAM ID (0 ~ 255)
BAUDRATE (2400 / 4800 / 9600 /
57600 / 115200)
V EW ANGLE
SPECIAL
NITIAL
LANGUAGE
ENGLISH / CHINESE / CHINESE (S) /
JAPANESE / KOREAN
COLOR GAIN
EXIT JUMP
EXIT JUMP
QUICK ZOOM
OFF / ON
ALARM
EXIT JUMP
CB LEVEL
0 ~ 20
CR LEVEL
0 ~ 20
Y LEVEL
0 ~ 20
V-SIZE
0 ~ 31
H-SIZE
0 ~ 40
V-POS.
0 ~ 30
H-POS.
0 ~ 39
ZONE DISP.
EXIT JUMP
MANUAL / DC
OFF / HME / BLC / WDR
OFF / ON
OFF / x2 ~ x64
OFF / LOW / MID / HIGH
SAVE & EXIT / EXIT
ATW / AWB / PUSH /
MANUAL
0 ~ 20
SAVE & EXIT / EXIT
AUTO / COLOR / B&W
AUTO / EXT.
LOW / MIDDLE / HIGH
SAVE & EXIT / EXIT
OFF / ON
OFF / ON
SAVE & EXIT / EXIT
OFF / ON
SHAKING - OFF / ON
SHAKE SCALE - 0~20
BRIGHT CHG. - OFF / ON
BRIGHT SCL. - 0~20
SAVE & EXIT / EXIT
0 ~ 15
OFF / ON
NORMAL / 4 3 / 16 9
DEFECT DET. / TV MODE / O.L.P.F
ON
SAVE & EXIT / EXIT
DAY & NIGHT
EXIT
EXIT JUMP
SAVE & EXIT / EXIT

14
EXPOSURE
LENS
Manual Manual mode supports the fixed board lens or the manual
iris lens.
DC DC mode supports the auto-iris varifocal lens.
NOTE: Both MANUAL and DC mode have FOCUS ADJ. You can
adjust the focus by finding the highest number on the FOCUS SET.
DC Lens Submenu MANUAL Lens Submenu
Mode: MANUAL: Set the lens mode to Normal or Deblur.
DC: Set the lens mode to Outdoor, Indoor, or Deblur.
Brightness: Adjust the camera’s brightness from 0~20. The higher the
number, the brighter the image will appear.
Shutter: Set the shutter speed to AUTO, Manual, or FLC (Flicker-less mode).
Select FLC if the camera is experiencing some flickering in the image. If selected, the
shutter speed will automatically be set to 1/100 for NTSC, or 1/120 for PAL.
If Manual is selected, set the shutter speed from 1/60 to 1/60000.
Focus Adjustment: When on, the default level is set automatically by
controlling lens focus and based on the installation and environment
circumstances.

15
EXPOSURE
BACKLIGHT
OFF
HME HIGHLIGHT MASKING EXPOSURE
HME allows objects to appear clearly on the screen by
masking extremely bright areas. To setup HME, set the
level and mode. The lower the setting, the darker the
masking areas have to be. Select from: 0 ~ 20.
Mode: Select when to enable HME settings. Select from
All Day (Run HME always), or Night Only (HME is
enabled only in B/W mode).
BLC BACK LIGHT COMPENSATION
If BLC is selected, adjust the size nad position of the mask:
- H-POS: Move the Zone position left or right. The higher the number,
the zone will move to the right.
- V-POS: Move the Zone position up or down. The higher he number,
the zone will move down.
- H-Size: Reset the zone‘s size horizontally. The higher the number,
the right side panel will move further to the right.
- V-Size: Reset the zone’s size vertically. The higher the number, the
bottom side panel will move further down.
WDR Wide Dynamic Range
If WDR is selected, adjust the WDR level in the submenu. Select
from Low, Middle, or High (Default).

16
EXPOSURE
DRC DYNAMIC RANGE COMPRESSOR
DRC enables dark areas in images to become more visible without overexposing he
bright areas to create one perfect image. Select from: Off, Low, Middle, or High
NOTE: If WDR or DEFOG are enabled, he DRC set ings are set automa ically and will not be available
for adjustment.
DEFOG Allows he camera to process a scene that is obscured by fog or weather conditions
and provides a visibly improved image.
AUTO / Manual: Select AUTO to have he WDR and DRC levels adjusted automa ically.
Set he DEFOG level from LOW / MIDDLE / HIGH.
AGC AUTO GAIN CONTROL
0~20 AGC enhances the picture brightness in low light conditions. A higher level AGC
setting makes the images brighter; however, it could increase the amount of noise.
STARLIGHT Automatically activates slow shutter function when the image is too dark.
OFF / x2 ~ x64 High values are not recommended as they may causes the image to lag.
(Default: X4) Starlight menu cannot be controlled if the SHUTTER setting is above 1/60.
3D DNR 3D DIGITAL NOISE REDUCTION
OFF/ LOW/ 3D-DNR reduces the noise on the screen in low light conditions and
MID/ HIGH allows for clearer images, even at night.

17
COLOR
ATW Auto Tracking White Balance Control mode compensates for color temperature changes
between 2400Koand 11000Ko.
AWB Auto White Balance Control mode compensates for color temperature changes
lower han 2000Koand higher than 15000Ko.
PUSH Push fixes the white balance based on he current lighting automatically.
MANUALUsers can control the white balance manually by changing RED GAIN and BLUE
GAIN (see below).
KELVIN: Select from Low, Middle, or High. If enabled, the Red and Blue Gain
settings will be set automatically according to the Kelvin settings.
RED GAIN: 0 ~ 20. Adjusts the amount of red in the image.
BLUE GAIN: 0 ~ 20. Adjust the amount of blue in the image.
COLOR GAIN
Set the color gain from 0~20.
WB MODE

18
DAY & NIGHT
AUTO / In AUTO mode, the camera switches between day and night automatically depending
COLOR / on light level. If COLOR is selected, the camera always stays in day/color mode.
B&W If B&W is selected, camera always stays in night/B&W mode.
CONTROL
Select if the Day/ Night switch will be based on he AGC levels (AUTO),
or using IR LED lights (EXT.)
AUTO: if selected, Day/ Night switch will depend on the AGC levels.
- AGC Threshold: Set when the camera switches between Day & Night.
- AGC Margin: Set the value added to the AGC Threshold. Adjust the
value based on the environment in which the camera is installed.
- Night Mode: Select what will the camera do when light threshold is met
for “Night Mode”. Select to keep in color, or switch to B&W.
- At the bottom of the screen, the settings will be summarized for your
review. The information includes (according to current set ings), he AGC
threshold for Day to switch to Night, AGC threshold for Night to switch
back to Day, and current AGC level, for reference.
EXT.: if selected, adjust the external signal to CDS or LOW/HIGH.
- Low/ High: The camera’s Day/ Night switch will be set according to an external LED board.
Set to HIGH to make the camera switch to night mode only when there is very lit le light.
- Night Mode: Select what will the camera do when light threshold is met for “Night Mode”.
for “Night Model”. Select to keep in color, or switch to B&W.
- At the bottom of the screen, the settings will be summarized for your review. The information
includes (according to current settings), the EXT level for Day to switch to Night, EXT level for
Night to switch back to Day, and current EXT level, for reference.
D&N MODE

19
DAY & NIGHT
CONTROL (CONT.)
- CDS: The camera’s Day/ Night switch will be set according to the LED board in the camera.
* CDS Threshold: Marks he light level at which the camera will switch between color and B/W.
The lower the value, the camera will require less light (more darkness)
to switch to Night Mode.
* CDS Signal: The value added to the CDS Threshold. Adjust his value
based on the environment in which the camera is installed.
- Night Mode: Select what will the camera do when the light threshold is
met for “Night Model”. Select to keep in color, or switch to B&W.
- At the bottom of the screen, the settings will be summarized for your
review. The information includes (according to current settings), the CDS
threshold for Day to switch to Night, CDS threshold for Night to switch
back to Day, and current CDS level, for reference.
EXT LED
AUTO / OFF AUTO: Enables the IR LED board. OFF: disable the camera’s LEDs.
DELAY
Low/Mid/High Time interval delay before switching from day mode to night mode.
B&W BURST
ON / OFF If ON is selected, the camera provides a color burst signal in night mode.
SMART IR
0 ~ 20 Enable Smart IR and set the level. Higher values will make Smart IR stronger.

20
FUNCTION
Mirror & Flip ONFlip ONMirror ONMirror / Flip OFF
D-Zoom
1.0x ~ 8.0x Enable or Disable Digital zoom to the camera’s field of view. By default, the zoom
will go to the center of the camera’s Field of View.
SHARPNESS
0 ~ 10 Sets the image sharpness. The higher the number, the sharper the image.
GAMMA
0.45 ~ 0.65 Select the desired gamma level. 0.55 is default setting.
MIRROR / FLIP
OFF
M RROR Reflects the camera horizontally.
FLIP Reflects the camera vertically.