Digitus DS-30040-2 User manual

PCI EXPRESS PARALLEL
CARD, 2/1-PORT
User Manual
DS-30040-2

Description
The PCI Express Parallel Card, 2/1-port is a single chip solution
that fully integrates PCIe2.0 Gen 1 end-point controller. It has
two serial ports and one parallel port, which can be easily to
expand more devices. The serial port supports RS-232 protocol
and it has transmission speed up to 115200bps, also it supports
hardware, software flow control. The Parallel port is a
bidirectional extension of the existing PC parallel interface; it is
compatible with IEEE1284-SPP/Byte/ECP mode.
Specification
Single-lane(x1)PCI-Express End-point controller
with PHY integrated
Compliant with PCI Express 2.0 Gen1
Compliant with PCI Power Management 1.2
Supports operating System: Linux kernel 4.x/3.x/2.6.x ,
Windows XP/Vista/Win7/Win8/Win8.1/
Win10 32/64bit

Serial port interface
Dual RS-232 port
Full serial Modem control
Supports hardware, software Flow control
Supports 5,6,7,8 and 9-bit Serial format
Supports Even, Odd, None, Space and Mark Parity
Supports Custom baud rate by internal PLL
Supports on chip 256 Byte depth FIFOs in Transmit, Receive
path of each serial port
Supports remote wakeup and power management features
Supports Slow IrDA mode(up to 115200bps) on all serial ports
Parallel port
Compatible with IEEE1284-SPP/Byte/ECP mode
Package content
1 x PCIe AX99100 Serial& Parallel card
1 x Serial cable within bracket
1 x User’s Manual
1 x CD
3 x Low profile bracket

System Requirements
Linux, Windows XP/Vista/Win7/Win8/Win8.1/
Win10 32bit or 64 bit
Available PCI Express slot x1
Hardware installation
Turn off the computer and unplug the power cord
Remove the computer cover and the PCIe card slot cover from
the slot that matches your PCIe card
Insert the PCIe card edge connector into the slot and secure
the bracket to the chassis
Replace the computer cover ,then plug in the power cord
Power on the computers
Install Drivers
Windows® Operating Systems
You must have administrative rights to the operating system to
install the drivers.
insert the CD driver bound with PCIe AX99100 Serial& Parallel
card driver into your CD-ROM drive:
if the Found New Hardware Wizard screen is displayed, click
Cancel

Find the drive disk and open the drive files.
Open the corresponding driver according to the system type:
Type for Windows XP/Vista/Win7:
For_32bit:
D:\Ax99100\xp.vista.win7\AX99100_Win7_
Vista_XP_32bit_Driver_v1.12.2.0_WHCK\ AX99100_Setup.exe
For_64bit:
D:\Ax99100\xp.vista.win7\AX99100_Win7_
Vista_XP_64bit_Driver_v1.12.2.0_WHCK\ AX99100_Setup.exe
Type for Windows 8/Win8.1/Win10
For_32bit:D:\Ax99100\win8.win8.1\win10\AX99100_
Win10_8.x_32bit_Driver_v1.18.2.0_WHCK\
AX99100_Setup.exe
For_64bit:
D:\Ax99100\win8.win8.1\win10\AX99100_
Win10_8.x_64bit_Driver_v1.18.2.0_WHCK\
AX99100_Setup.exe
Click “AX99100_Setup.exe”
Follow the instructions in the install wizard to finish it

To Verify Windows® Driver Installation
Click on the Device Manager tab in System Properties, which you
access from the Windows Control Panel. If you use the 2S1P card,
you should see Two “AX99100 PCIe to High Speed Serial Port”…
and one “AX99100 PCIe to Multi Mode Parallel Port”…installed
under Ports (COM & LPT) item.
Support
More information and settings please refer to the User Guides or
you can contact us.
Hereby Assmann Electronic GmbH, declares that the Declaration of Conformity is part
of the shipping content. If the Declaration of Conformity is missing, you can request it
by post under the below mentioned manufacturer address.
www.assmann.com
Assmann Electronic GmbH
Auf dem Schüffel 3
58513 Lüdenscheid
Germany