Digitus DN-80201 User manual

1
2SFP Port 10/100/1000Mbps
Web Smart Ethernet Switch
DN-80201
DN-80211-1
DN-80221-1
Manual
DN-80201 DN-80211-1 DN-80221-1

2
Table of Contents
Chapter 1 Product Introduction ..................................................................................... 4
1.1 Product Overview................................................................................................. 4
1.2 Features (8 port )………………………………………………………………………..4
1.2.1 Features ( 16 port )………….……………………………………………….……….5
1.2.2 Features ( 24 port )……………………………………………………………………5
1.3 External Component Description (8 port)…………………………………………….6
1.3.1 Front Panel (8 port)……………………………………………………………...6
1.3.2 Rear Panel (8 port)………………………………………………………………7
1.3.3 External Component Description (16 port)……………………………………..….8
1.3.4 Front Panel (16 port)………………………………………………………………….8
1.3.5 Rear Panel (16 port)………………………………………………………………….9
1.3.6 External Component Description (24 port)………………………………………..10
1.3.7 Front Panel (24 port)………………………………………………………………...10
1.3.8 Rear Panel (24 port)…………………………………………………………………11
1.4 Package Contents ( 8 port )…………………………………………………………..12
1.4.1 Package Contents ( 16 port )……………………………………………………….12
1.4.2 Package Contents ( 24 port )……………………………………………………….12
Chapter 2 Installing and Connecting the Switch…………………………………………13
2.1 Installation………………………………………………………………………………13
2.1.1 Desktop Installation ( 8 port )………………………………………………….13
2.1.2 Rack-mountable Installation in 19-inch Cabinet ( 8 port )…….……………13
2.1.3 Power on the Switch ( 8 port )………………………………………………..14
2.1.4 Desktop Installation ( 16 port )………………………………………………..14
2.1.5 Rack-mountable Installation in 19-inch Cabinet ( 16 port )………………..15
2.1.6 Power on the Switch ( 16 port )……………………………………………….16
2.1.7 Desktop Installation ( 24 port )………………………………………………..16
2.1.8 Rack-mountable Installation in 19-inch Cabinet ( 24 port )………………..17
2.1.9 Power on the Switch ( 24 port )……………………………………………….18
2.2 Connect Computer (NIC) to the Switch.............................................................. 18
Chapter 3 How to Login the Switch ( 8 port )……………………………………………..18
3.1 Switch to End Node ( 8 port )…………………………………………………………18
3.2 How to Login the Switch ( 8 port )……………………………………………………19
Chapter 3 How to Login the Switch ( 16 port )…………………………………………….21
3.3 Switch to End Node ( 16 port )………………………………………………………..21
3.4 How to Login the Switch ( 16 port )…………………………………………………..21
Chapter 3 How to Login the Switch ( 24 port )…………………………………………….23
3.5 Switch to End Node ( 24 port )………………………………………………………..23
3.6 How to Login the Switch ( 24 port )…………………………………………………..23
Chapter 4 Switch Configuration …………………………………………………………….25
4.1 Status................................................................................................................. 25
4.1.1 System Information.................................................................................. 25

3
4.1.2 Logging Message .................................................................................... 26
4.1.3 Port .......................................................................................................... 26
4.1.4 Link Aggregation ...................................................................................... 28
4.1.5 LLDP Statistics......................................................................................... 28
4.1.6 IGMP Snooping Statistics ........................................................................ 29
4.2 Network.............................................................................................................. 30
4.2.1 IP Address ............................................................................................... 30
4.2.2 Time Settings ........................................................................................... 30
4.3 Switching............................................................................................................ 31
4.3.1 Port Setting .............................................................................................. 31
4.3.2 Error Disabled.......................................................................................... 32
4.3.3 Mirror ....................................................................................................... 33
4.3.4 Link Aggregation ...................................................................................... 33
4.3.5 Vlan Management.................................................................................... 36
4.3.6 Multicast ................................................................................................. 39
4.3.7 Jum bo Frame.......................................................................................... 44
4.3.8 STP.......................................................................................................... 45
4.4 Mac Address Table............................................................................................. 48
4.4.1 Static Mac Setting .................................................................................... 48
4.4.2 MAC Filtering ........................................................................................... 49
4.4.3 Dynamic Address Setting......................................................................... 49
4.4.4 Dynamic Learned..................................................................................... 50
4.4.5 RMA MAC Address .................................................................................. 50
4.5 Security.............................................................................................................. 50
4.5.1 Storm Control........................................................................................... 50
4.5.2 802.1X ..................................................................................................... 51
4.5.3 DHCP Snooping....................................................................................... 53
4.5.4 Port Security ............................................................................................ 57
4.5.5 AAA.......................................................................................................... 58
4.5.6 Tacacs+ Server ........................................................................................ 61
4.5.7 Radius server........................................................................................... 61
4.5.8 Access ..................................................................................................... 62
4.6 ACL .................................................................................................................... 65
4.6.1 MAC-Based ACL...................................................................................... 65
4.6.2 MAC-Based ACE ..................................................................................... 65
4.6.3 IPv4-Based ACL ...................................................................................... 65
4.6.4 IPv4-Based ACE ...................................................................................... 66
4.6.5 ACL Binding ............................................................................................. 66
4.7 QoS.................................................................................................................... 67
4.7.1 General .................................................................................................... 67
4.7.2 QoS Basic Mode...................................................................................... 69
4.7.3 QoS Advanced Mode ............................................................................... 70
4.7.4 Rate Limit................................................................................................. 73
4.8 Management ...................................................................................................... 74

4
4.8.1 LLDP........................................................................................................ 74
4.8.2 SNMP ...................................................................................................... 78
4.8.3 RMON...................................................................................................... 82
4.9 Diagnostics ........................................................................................................ 84
4.9.1 System Status.......................................................................................... 84
4.9.2 Ping Test .................................................................................................. 84
4.9.3 Logging Setting........................................................................................ 85
4.9.4 Factory Default ........................................................................................ 86
4.9.5 Reboot Switch.......................................................................................... 86
4.10 Maintenance .................................................................................................... 87
4.10.1 Backup Manager.................................................................................... 87
4.10.2 Upgrade Manager.................................................................................. 88
4.10.3 Configuration Manager .......................................................................... 88
4.10.4 Account Manager................................................................................... 89
4.10.5 Enable Password................................................................................... 90

5
Chapter 1 Product Introduction
Congratulations on purchasing of the Web Smart Ethernet Switch. Before you install and
use this product, please read this manual carefully for full exploiting the functions of this
product.
1.1 Product Overview
The 8/16/24 port + 2SFP 10/100/1000Mbps Managed Ethernet Switch provides seamless
network connection. It integrates 10/100/1000Mbps Ethernet network capabilities, and
can be configured by web based interface. Including administrator, port management,
VLAN setting, port statistics, trunking, QoS setting, security filter, configuration/
backup/recovery, log out, and so on.
1.2 Features (8 port )
Complies with IEEE802.3, IEEE 802.3u, IEEE 802.3ab standards
8 x 10/100/1000Mbps Auto-Negotiation RJ45 ports supporting Auto-MDI/MDIX
Support Console port management
Supports IEEE802.3x flow control for Full-duplex Mode and back pressure for
Half-duplex Mode
8K entry MAC address table with auto-learning and auto-aging
Supports WEB management interface
LED indicators for monitoring power, link, activity and speed

6
1.2.1 Features (16 port)
 Comply with IEEE802.3, IEEE802.3u, IEEE802.3ab, IEEE802.3x, IEEE802.3z,
EEE802.3ad standards
 Supports IEEE802.3x flow control for Full-duplex Mode and back pressure for
Half-duplex Mode
 Supports MAC address auto-learning and auto-aging
 Store and forward mode operates
 Support SNMP/RMON/TELENT
 Supports IEEE802.1Q VLAN,4K VLAN Table
 Support IEEE802.1p Priority Queues
 Support ACL Function, 1.5K-entry ALC table
 Support Storm Control
 Support QoS, Port Mirroring, Link Aggregation Protocol
 LED indicators for monitoring power, link/activity
 Web-based Management Support
 Internal power adapter supply

1.2.2 Features (24 port)
 Comply with IEEE802.3, IEEE802.3u, IEEE802.3ab, IEEE802.3x, IEEE802.3z,
EEE802.3ad standards
 Supports IEEE802.3x flow control for Full-duplex Mode and back pressure for
Half-duplex Mode
 Supports MAC address auto-learning and auto-aging
 Store and forward mode operates
 Support SNMP/RMON/TELENT
 Supports IEEE802.1Q VLAN,4K VLAN Table
 Support IEEE802.1p Priority Queues
 Support ACL Function, 1.5K-entry ALC table
 Support Storm Control
 Support QoS, Port Mirroring, Link Aggregation Protocol
 LED indicators for monitoring power, link/activity
 Web-based Management Support
 Internal power adapter supply


7
1.3 External Component Description (8 port)
1.3.1 Front Panel (8 port)
The front panel of the Switch consists of 8 x 10/100/1000Mbps RJ-45 ports, 2 x SFP
ports, 1 x Console port, 1 x Reset button and a series of LED indicators as shown as
below.
Figure 1 - Front Panel
10/100/1000Mbps RJ-45 ports (1~8):
Designed to connect to devices with a bandwidth of 10Mbps, 100Mbps or 1000Mbps.
Each has a corresponding 10/100/1000Mbps LED.
SFP ports (SFP1, SFP2):
Designed to install SFP module and connect to devices with a bandwidth of 1000Mbps.
Each has a corresponding 1000Mbps LED.
Console port (Console):
Designed to connect with serial port of a computer or terminal for monitoring and
configuring the Switch.
Reset button (Reset):
Keep the device powered on and press down the button for about 5 seconds. The
system restores the factory default settings.
LED indicators:
The LED Indicators will allow you to monitor, diagnose and troubleshoot any potential
problem with the Switch, connection or attached devices.

8
Figure 2 - LED Indicators
The following chart shows the LED indicators of the Switch along with explanation of each
indicator.
LED COLOR STATUS STATUS DESCRIPTION
Power Green
On Power On
Off Power Off
LNK/ACT/
Speed
(1~8)
10/100Mbps:
Orange
On A device is connected to the port
Off No device is connected to the port
1000Mbps:
Green Flashing Sending or receiving data
SFP1
SFP2 Green
On A device is connected to the port
Off No device is connected to the port
Flashing Sending or receiving data
1.3.2 Rear Panel (8 port)
The rear panel of the Switch contains AC power connector shown as below.
Figure 3 - Rear Panel
AC Power Connector:
Power is supplied through an external AC power adapter. It
supports AC 100~240V,
50~60Hz.

9
1.3.3 External Component Description (16 port)
1.3.4 Front Panel (16 port)
The front panel of the Switch consists of 16 x 10/100/1000Mbps RJ-45 ports, 2 x SFP
ports, 1 x Console port, 1 x Reset button and a series of LED indicators as shown as
below.
Figure 1 - Front Panel
10/100/1000Mbps RJ-45 ports (1~16):
Design to connect to the device with a bandwidth of 10Mbps, 100Mbps or 1000Mbps.
Each has a corresponding 10/100/1000Mbps LED.
SFP ports (SFP1, SFP2):
Design to install the SFP module and connect to the device with a bandwidth of 1000Mbps.
Each has a corresponding 1000Mbps LED.
Console port (Console):
Design to connect with the serial port of a computer or terminal for monitoring and
configuring the Switch.
Reset button (Reset):
Keep the device powered on and press down the button for about 5 seconds. The system
restores the factory default settings.
LED indicators:
The LED Indicators will allow you to monitor, diagnose and troubleshoot any potential
problem with the Switch, connection or attached devices.
Figure 2 - LED Indicators

10
The following chart shows the LED indicators of the Switch along with explanation of each
indicator.
LED COLOR STATUS STATUS DESCRIPTION
Power Red
On Power On
Off Power Off
LNK/ACT/
Speed
(1~16)
10/100Mbps:
Orange
On A device is connected to the port
Off No device is connected to the port
1000Mbps:
Green Flashing Sending or receiving data
SFP1
SFP2 Green
On A device is connected to the port
Off No device is connected to the port
Flashing Sending or receiving data
1.3.5 Rear Panel (16 port)
The rear panel of the Switch contains AC power connector shown as below.
Figure 3 - Rear Panel
AC Power Connector:
Power is supplied through an external AC power adapter. It
supports AC 100~240V,
50~60Hz.
Grounding Terminal:
The Switch already comes with Lightning Protection Mechanism. You can also ground
the Switch through the PE (Protecting Earth) cable of AC cord or with Ground Cable.

11
1.3.6 External Component Description (24 port)
1.3.7 Front Panel (24 port)
The front panel of the Switch consists of 24 x 10/100/1000Mbps RJ-45 ports,2 x SFP
ports,1 x Console port, 1 x Reset button and a series of LED indicators as shown as
below.
Figure 1 - Front Panel
10/100/1000Mbps RJ-45 ports (1~24):
Design to connect to the device with a bandwidth of 10Mbps, 100Mbps or 1000Mbps.
Each has a corresponding 10/100/1000Mbps LED.
SFP ports (SFP1, SFP2):
Design to install the SFP module and connect to the device with a bandwidth of 1000Mbps.
Each has a corresponding 1000Mbps LED.
Console port (Console):
Design to connect with the serial port of a computer or terminal for monitoring and
configuring the Switch.
Reset button (Reset):
Keep the device powered on and press down the button for about 5 seconds. The system
restores the factory default settings.
LED indicators:
The LED Indicators will allow you to monitor, diagnose and troubleshoot any potential
problem with the Switch, connection or attached devices.
Figure 2 - LED Indicators

12
The following chart shows the LED indicators of the Switch along with explanation of each
indicator.
LED COLOR STATUS STATUS DESCRIPTION
Power Red
On Power On
Off Power Off
LNK/ACT/
Speed
(1~24)
10/100Mbps:
Orange
On A device is connected to the port
Off A device is disconnected to the port
1000Mbps:
Green Flashing Sending or receiving data
SFP1
SFP2 Green
On A device is connected to the port
Off A device is disconnected to the port
Flashing Sending or receiving data
1.3.8 Rear Panel (24 port)
The rear panel of the Switch contains AC power connector and one marker shown as
below.
Figure 3 - Rear Panel
AC Power Connector:
Power is supplied through an external AC power adapter. It
supports AC 100~240V,
50~60Hz.
Grounding Terminal:
The Switch already comes with Lightning Protection Mechanism. You can also ground
the Switch through the PE (Protecting Earth) cable of AC cord or with Ground Cable.
1.4 Package Contents (8 port)
Before installing the Switch, make sure that the following "packing list" listed OK. If any

13
part is lost and damaged, please contact your local agent immediately. In addition, make
sure that you have the tools install switches and cables by your hands.
 One Web Smart Ethernet Switch
 Four rubber feet, two mounting ears and eights screws
 One AC power cord
 One User Manual
1.4.1 Package Contents (16 port)
Before installing the Switch, make sure that the following the "packing list" listed OK. If any
part is lost and damaged, please contact your local agent immediately. In addition, make
sure that you have the tools install switches and cables by your hands.
 One Web Smart Ethernet Switch
 Four rubber feet, two mounting ears and eights screws
 One AC power cord
 One User Manual
1.4.2 Package Contents (24 port)
Before installing the Switch, make sure that the following the "packing list" listed OK. If any
part is lost and damaged, please contact your local agent immediately. In addition, make
sure that you have the tools install switches and cables by your hands.
 One Web Smart Ethernet Switch
 Four rubber feet, two mounting ears and eights screws
 One AC power cord
 One User Manual

14
Chapter 2 Installing and Connecting the Switch
This part describes how to install your Web Smart Ethernet Switch and make connections
to it. Please read the following topics and perform the procedures in the order being
presented.
2.1 Installation
Please follow the following instructions in avoid of incorrect installation causing device
damage and security threat.
Put the Switch on stable place or desktop in case of falling damage.
Make sure the Switch works in the proper AC input range and matches the voltage
labeled on the Switch.
To keep the Switch free from lightning, do not open the Switch’s shell even in power
failure.
Make sure that there is proper heat dissipation from and adequate ventilation around
the Switch.
Make sure that the cabinet has enough back up for the weight of the Switch and its
accessories.
2.1.1 Desktop Installation (8 port)
Sometimes users are not equipped with the 19-inch standard cabinet. So when installing
the Switch on a desktop, please attach these cushioning rubber feet provided on the
bottom at each corner of the Switch in case of the external vibration. Allow adequate
space for ventilation between the device and the objects around it.
2.1.2 Rack-mountable Installation in 19-inch Cabinet ( 8 port )
The Switch can be mounted in an EIA standard-sized, 19-inch rack, which can be placed
in a wiring closet with other equipment. To install the Switch, please follow these steps:
a. Attach the mounting brackets on the Switch’s side panels (one on each side) and
secure them with the screws provided.
Figure 4 - Bracket Installation

15
b. Use the screws provided with the equipment rack to mount the Switch on the rack
and tighten it.
Figure 5 - Rack Installation
2.1.3 Power on the Switch (8 port)
The Switch is powered by AC 100-240V 50/60Hz internal high-performance power supply.
Please follow the next tips to connect:
AC Electrical Outlet:
It is recommended to use single-phase three-wire receptacle with neutral outlet or
multifunctional computer professional receptacle. Please make sure to connect the metal
ground connector to the grounding source on the outlet.
AC Power Cord Connection:
Connect the AC power connector in the back panel of the Switch to external receptacle
with the included power cord, and check the power indicator is ON or not. When it is ON, it
indicates the power connection is OK.
2.1.4 Desktop Installation (16 port)
Sometimes users are not equipped with the 19-inch standard cabinet. So when installing
the Switch on a desktop, please attach these cushioning rubber feet provided on the
bottom at each corner of the Switch in case of the external vibration. Allow adequate
space for ventilation between the device and the objects around it.

16
Figure 4 - Desktop Installation
2.1.5 Rack-mountable Installation in 19-inch Cabinet (16 port)
The Switch can be mounted in an EIA standard-sized, 19-inch rack, which can be placed
in a wiring closet with other equipment. To install the Switch, please follow these steps:
c. Attach the mounting brackets on the Switch’s side panels (one on each side) and
secure them with the screws provided.
Figure 5 - Bracket Installation
d. Use the screws provided with the equipment rack to mount the Switch on the rack
and tighten it.

17
Figure 6 - Rack Installation
2.1.6 Power on the Switch (16 port)
The Switch is powered on by the AC 100-240V 50/60Hz internal high-performance power
supply. Please follow the next tips to connect:
AC Electrical Outlet:
It is recommended to use single-phase three-wire receptacle with neutral outlet or
multifunctional computer professional receptacle. Please make sure to connect the metal
ground connector to the grounding source on the outlet.
AC Power Cord Connection:
Connect the AC power connector in the back panel of the Switch to external receptacle
with the included power cord, and check the power indicator is ON or not. When it is ON, it
indicates the power connection is OK.
2.1.7 Desktop Installation (24 port)
Sometimes users are not equipped with the 19-inch standard cabinet. So when installing
the Switch on a desktop, please attach these cushioning rubber feet provided on the
bottom at each corner of the Switch in case of the external vibration. Allow adequate
space for ventilation between the device and the objects around it.

18
Figure 4 - Desktop Installation
2.1.8 Rack-mountable Installation in 19-inch Cabinet (24 port)
The Switch can be mounted in an EIA standard-sized, 19-inch rack, which can be placed
in a wiring closet with other equipment. To install the Switch, please follow these steps:
e. Attach the mounting brackets on the Switch’s side panels (one on each side) and
secure them with the screws provided.
Figure 5 - Bracket Installation

19
f. Use the screws provided with the equipment rack to mount the Switch on the rack
and tighten it.
Figure 6 - Rack Installation
2.1.9 Power on the Switch (24 port)
The Switch is powered on by the AC 100-240V 50/60Hz internal high-performance power
supply. Please follow the next tips to connect:
AC Electrical Outlet:
It is recommended to use single-phase three-wire receptacle with neutral outlet or
multifunctional computer professional receptacle. Please make sure to connect the metal
ground connector to the grounding source on the outlet.
AC Power Cord Connection:
Connect the AC power connector in the back panel of the Switch to external receptacle
with the included power cord, and check the power indicator is ON or not. When it is ON, it
indicates the power connection is OK.
2.2 Connect Computer (NIC) to the Switch
Please insert the NIC into the computer, after installing network card driver, please
connect one end of the twisted pair to RJ-45 jack of your computer, the other end will be
connected to any RJ-45 port of the Switch, the distance between Switch and computer is
around 100 meters. Once the connection is OK and the devices are power on normally,
the LINK/ACT/Speed status indicator lights corresponding ports of the Switch.

20
Chapter 3 How to Login the Switch (8 port)
3.1 Switch to End Node (8 port)
Use standard Cat.5/5e Ethernet cable (UTP/STP) to connect the Switch to end nodes as
described below. Switch ports will automatically adjust to the characteristics (MDI/MDI-X,
speed, duplex) of the device to which is connected.
Figure 6 - PC Connect
Please refer to the LED Indicator Specification. The LINK/ACT/Speed LEDs for each port
lights on when the link is available.
3.2 How to Login the Switch (8 port)
As the Switch provides Web-based management login, you can configure your computer’s
IP address manually to log on to the Switch. The default settings of the Switch are shown
below.
Parameter Default Value
Default IP address 192.168.2.1
Default user name admin
Default password admin
You can log on to the configuration window of the Switch through following steps:
1. Connect the Switch with the computer NIC interface.
2. Power on the Switch.
3. Check whether the IP address of the computer is within this network segment:
192.168.2.xxx (“xxx” ranges 2~254), for example, 192.168.2.100.
4. Open the browser, and enter http://192.168.2.1 and then press “Enter”. The Switch
login window appears, as shown below.