Dimplex DCACP25 User manual

For domestic household use only.
INSTRUCTION MANUAL
Dimplex Pedestal Air Circulator
Models: DCACP25

IMPORTANT
THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR
FUTURE REFERENCE. Note also the information presented on the appliance
CAUTION: FAILURE TO FOLLOW THESE INSTRUCTIONS MAY CAUSE INJURY AND/
OR DAMAGE AND MAY INVALIDATE YOUR GUARANTEE
Please read the operating instructions carefully before using your fan for the first time
and keep them in a safe place.
WARNING
• To prevent against the risk of electric shock never immerse the appliance in water
or other liquids.
• Never operate the appliance if a cable or connector has been damaged, after
appliance malfunction or if the appliance was dropped or is otherwise damaged.
• If the mains lead is damaged it must only be replaced by the manufacturers’ service
agent or a similarly qualified person in order to avoid a hazard.
• Please ask a professional service agent to repair the product. Improper repair may
cause danger to users.
• Disconnect the appliance from mains power whenever it is not in use, before
relocating it, and before cleaning.
• Operate the appliance only at the voltage specified on the rating label.
• This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of
the appliance in a safe way and understand the hazards involved. Children shall
not play with the appliance. Cleaning and user maintenance shall not be made by
children without supervision.
• Keep electrical appliances out of reach from children or infirm persons. Do not let
them use the appliances without supervision.
• When the fan is assembled, the rotor blade guard should not be taken o again.
• Indoor use only.
RULES FOR SAFE OPERATION
• Never insert fingers, pencils, or any other object through the grille when fan is
running.
• Disconnect the fan when moving from one location to another.
• Be sure the fan is on a stable surface when operating to avoid overturning.
• DO NOT use the fan in a window, rain may create an electrical hazard.
• Household use only.

Installation Intructions
STRUCTURE
1. Base plate
2. Power cord
3. Button
4. Screw
5. Column
6. Button
7. Bracket
8. Rear grill
9. Handle
10. Fan blade
11. Front cover
ASSEMBLY INSTRUCTIONS
1. Install the column on the base.
2. Install the motor part on the column.

Remote and Display
REMOTE
1. On/O button
2. Mode button
3. Swing/Oscillation button
4. Fan speed button
5. Timer button
DISPLAY/CONTROL PANEL
1. On/O button
2. Fan speed button
3. Mode button
4. Swing/Oscillation button
5. Timer button
Operation Instructions
When you first plug in, the fan will make a sound alert and then enter standby
mode. Only the [ON/OFF] button is operational in standby mode.
ON/OFF
While in stand-by mode, press the [ON/OFF] button to turn the fan on.
Pressing the [ON/OFF] button when the fan is operational will turn the fan o. The
indicator light will also turn o. If the fan is oscillating then the motor will return
back to the central point first and then go into standby mode.

FAN SPEED
The wind speed can be adjusted with the [FAN SPEED] button. Pressing the button
repeatedly will rotate between Low, Medium and High wind speeds.
MODES
The wind mode can be adjusted by pressing the [MODE] button. Pressing the
button repeatedly will rotate between Normal, Natural breeze, Sleep modes.
Normal Mode: Operates normally with the selected wind speed - Low, Medium,
High.
Natural Breeze Mode: The fan speed automatically shifts through Low, Medium,
High speed to imitate a natural wind speed rhythm.
Sleep Mode: The fan will run using the Natural Breeze mode pattern and
automatically lower the set wind speed in 30 minute intervals depending on the
speed setting and then run continuously at low speed.
Sleep on High: high speed for half an hour, then medium speed for half an hour, then
low speed continuously
Sleep on Medium: medium speed for half an hour, then low speed continuously
Sleep on low: low speed continuously
TIMER
The [TIMER] button has 4 timer settings in the order of 1H, 2H, 4H, 8H, OFF. The
LED display will indicate which time frame is set. Selecting the relative settings will
start the timer and once the timer runs out the fan will automatically turn o. After
resetting the timer, the fan will work according to the last setting.
The timer can be preset in stand-by mode, presets can be set to 1H, 2H, 4H, 8H and
will be displayed accordingly on the LED display. The fan will start in the mode last
used.
SWING/OSCILLATION
Press the [SWING/OSCILLATION] button, the indicator light will switch on and the
fan will oscillate between 00and 900. When shifting directions the fan will stop for 2
seconds and then continue to oscillate.
Note: when the fan is first plugged in the fan will oscillate 300to calibrate its
settings.

Maintenance Instructions
The fan requires little maintenance. Do not try to fix it by yourself. Refer it to a
qualified service person if service is needed.
1. Unplug the fan before cleaning and assembling.
2. To ensure there is adequate air circulation to the motor, keep the rear vents free
of dust. DO NOT disassemble the fan to remove dust.
3. To clean exterior parts, wipe with a soft cloth soaked in mild detergent.
4. DO NOT use any abrasive detergents or solvents to avoid scratching the surface.
5. DO NOT use any of the following as a cleaner: gasoline or thinner.
6. DO NOT allow water or any other liquid into the motor housing or interior parts.
7. Store fan in a dry and cool area.
Disposal
DO NOT dispose of electrical appliances as unsorted municipal
waste, use seperate collection facilities. Contact your local
government for information regarding the collection systems
available. If electrical appliances are disposed of in landfills or
dumps, hazardous substances can leak into the groundwater and
get into the food chain, damaging your health and well-being.
Cleaning
1. Be sure to unplug the fan from the electrical supply source before cleaning.
2. Plastic parts should be cleaned with a soft cloth moisten with mild soap.
3. Thoroughly remove soap film with dry cloth.