Dimplex EF3003-230 User manual

PRACTICAL USER’S GUIDE
FOR THE ELECTRIC FIREPLACE
MODEL NUMBER:
EF3003-230
Valued Customer,
We are pleased that you have chosen to purchase an electric
fireplace manufactured by Dimplex North America Ltd.
Over the years, valuable memories ill occur around the
armth and comfort of your hearth. Thank you for allo ing our
product to be the backdrop for those special moments.
7206700100REV02
Quality checked by:

CONTENTS
PAGE 1 Important Instructions
PAGE 2 Model and Serial Number
Information
PAGE 3 Site selection and preparation
PAGE 5 Fireplace Installation
PAGE 6 Operation
PAGE 9 Maintenance
PAGE 12 Warranty

QUICK REFERENCE GUIDE FOR THE DIMPLEX ELECTRIC
FIREPLACE
1. Prior to the first use of the fireplace verify the following:
• Are the circuit breakers for the unit on?
• Are the light bulbs in your fireplace loose? (to check, follow the
instructions for replacing the light bulbs under the maintenance
section of this manual)
2. The heater on your fireplace may emit a slight, harmless odor when
first used. This odor is a normal condition caused by the initial
heating of internal heater parts and will not occur again.
3. If your heater does not emit heat, ensure the switch is on and the
thermostat is turned fully clockwise. If this does not work, switch the
unit off for 5 minutes and try again. Consult page 5 of your Practical
User’s Guide for further information.

IMPORTANT INSTRUCTIONS
SAVE THESE INSTRUCTIONS
PLEASE RETAIN THIS USER’S GUIDE FOR FUTURE REFERENCE
When using electrical appliances, basic precautions should always be followed to reduce the risk of fire,
electric shock, and injury to persons, including the following:
1. Read all instructions before using the electric fireplace.
2. This fireplace is hot when in use. To avoid burns, do not let bare skin touch hot
surfaces. The trim around the heater outlet becomes hot during heater operation. Keep
combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3
feet (0.9m) from the front of the unit.
3. Extreme caution is necessary when any heater is used by or near children or invalids and whenever
the unit is left operating and unattended.
4. Young children should be supervised to ensure that they do not play with the appliance.
5. The appliance is not intended for use by young children or infirmed persons without supervision.
6. The appliance must be positioned so that the plug is accessible.
7. Always unplug the electric fireplace when not in use.
8. If the supply cord is damaged, it must be replaced by the manufacturer, or its service agent, or a
qualified person in order to avoid a hazard.
9. Do not operate any unit with a damaged cord or plug, or if the heater has malfunctioned, or if the
electric fireplace has been dropped or damaged in any manner. Return heater to authorized service
facility for examination, electrical or mechanical adjustment, or repair.
10. Do not use outdoors.
11. Do not use this fireplace in the immediate surroundings of a bath, a shower or a swimming pool.
12. Do not install the fireplace directly on carpet or a similar surface which may restrict air circulation
beneath the unit.
13. Do not run the cord under carpeting. Do not cover cord with throw rugs, runners, or the like.
Arrange cord away from traffic area and where it will not be tripped over.
14. Do not locate the heater immediately below a fixed socket-outlet.
15. To disconnect the fireplace, turn the controls off, then remove the plug from the outlet.
16. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause
an electric shock or fire, or damage to the heater.
17. To prevent a possible fire, do not block air intake or exhaust in any manner. Do not use on soft
surfaces, like a bed, where openings may become blocked.
18. All electrical heaters have hot and arching or sparking parts inside. Do not use in areas where
gasoline, paint, or flammable liquids are used or stored or where the unit will be exposed to
flammable vapors.
19. Do not modify the electric fireplace. Use it only as described in this manual. Any other use not
recommended by the manufacturer may cause fire, electric shock or injury to persons.
20. Avoid the use of an extension cord. Extension cords may overheat and cause a risk of fire. If you
must use an extension cord, the cord must be 3-core type and have a rating no less than 13 amps.
21. Do not burn wood or other materials in the electric fireplace.
22. Do not strike the fireplace glass.
23. Always use a certified electrician should new circuits or outlets be required.
24. Always use properly grounded, fused and polarized outlets.
25. Disconnect all power supply before performing any cleaning, maintenance or relocation of the unit.
26. When transporting or storing the unit and cord, keep in a dry place, free from excessive vibration
and store so as to avoid damage.
NOTE: Procedures and techniques that are considered important enough to emphasize.
CAUTION: Procedures and techniques, which, if not carefully followed, will result in damage to the
equipment.
WARNING: Procedures and techniques, which, if not carefully followed, will expose the user to the risk of
fire, serious injury, illness or death.
1

Model Number
Serial Number
IMPORTANT INSTRUCTIONS
If you have any questions about our products please have the product model and serial
numbers available upon calling Dimplex customer service. To locate the model and serial
number labels see below.
2
Firebox Carton

SITE SELECTION AND PREPARATION
This section provides easy step by step instructions for selecting a location and preparing the
site to install the fireplace into:
• Existing Fireplace
• New wall construction
• Dimplex mantel surround kit or custom made mantel surround
NOTE
The fireplace insert comes completely assembled and
wired. Some tools may be required to prepare the
site and assembly/install the trim.
The dimensions of the fireplace insert are 762mm
wide X 641mm high X 286mm deep. (FIGURE 1)
You should allow 6mm around the fireplace insert for
ease of installation.
This fireplace does not require any venting.
CAUTION
Clearance for air circulation beneath the fireplace insert is
provided by three rubber feet (FIGURE 1).
DO NOT INSTALL THE FIREPLACE INSERT
DIRECTLY ON CARPET OR SIMILAR SURFACES
WHICH MAY RESTRICT AIR CIRCULATION. If
installing the fireplace in a carpeted area, place a
one-piece, solid, flat surface under the fireplace
insert. Ensure that all three of the insert’s feet rest
securely on this surface.
EXISTING FIREPLACE INSTALLATION
1. Seal all drafts and vents with non-fibrous
insulation materials to prevent chimney debris
from falling into the fireplace insert. Do not
install into an existing fireplace that is prone to
leaks or dampness.
2. Cap the top of the chimney flue to prevent rain
from entering.
3. Plan your electrical power supply: (refer to
NOTE 1)
4. The power cord can run along the front of the
hearth to an outlet near the fireplace
(FIGURE 2).
3
FIGURE 1
FIGURE 2
762mm
641mm
286mm

NOTE
The fireplace insert must be installed on a hard
surface.
NOTE
A 13 AMP, 230 VOLT (240V in Australia) circuit is
required. A dedicated circuit is preferred but not
essential in all cases. A dedicated circuit will be
required if, after installation, the circuit breaker trips or
fuse blows on a regular basis when the heater is
operating. Additional appliances on the same circuit
may exceed the current rating of the circuit breaker.
WARNING
To prevent personal injury you should hire a
professional to cap the chimney flue or cut a hole in
the existing fireplace for wiring.
If you return your existing fireplace to its original use
(Example wood burning), it should be inspected by
the local building department prior to use to reduce
the risk of fire and personal injury.
NEW WALL CONSTRUCTION
1. Select a suitable location that is not susceptible to
moisture and is away from drapes, furniture and
high traffic.
2. Place the fireplace in the desired location to see
how it will look in the room.
3. Mark the desired location on the floor and store
the fireplace in a safe, dry and dust free location.
4. Use studs to frame an opening of 775mm wide X
654mm high X 305mm deep.
5. Plan your electrical power supply.
(refer to NOTE 1)
Option #1 - The power cord can be lead from behind
the trim and along the wall to an outlet near the
fireplace. (FIGURE 4)
Option #2 - A new outlet can be installed inside the
new frame construction. (if allowed by electrical
code). (FIGURE 5)
4
FIGURE 3
FIGURE 5
FIGURE 4
305mm
775mm
654mm

WARNING
Construction and Electrical Outlet wiring must
comply with local building codes and other
applicable regulations to reduce the risk of fire,
electrical shock and injury to persons.
WARNING
Do not attempt to wire your own new outlets or
circuits. To reduce the risk of fire, electric shock or
injury to persons, always use a licensed electrician.
MANTEL SURROUND KIT OR CUSTOM MADE
MANTEL SURROUND
1. Select a suitable location that is not susceptible to
moisture and is away from drapes, furniture and
high traffic.
2. Place the fireplace in the desired location to see
how it will look in the room.
3. For ease of electrical hook up you may wish to
locate the fireplace near an existing outlet. (refer
to NOTE 1)
4. Store the fireplace in a safe dry and dust free
location.
5. Assemble the mantel surround kit (refer to the
mantel assembly instructions) or construct the
custom surround with an opening of 775mm X
654mm X 305mm.
FIREPLACE INSERT INSTALLATION
This section provides easy step by step instructions for installation of your fireplace.
1. Install Trim Kit to front of fireplace by positioning
trim then pushing straight forward against the
fireplace.
2. Make sure the unit is switched OFF (Refer to
operating instruction section).
3. Plug the fireplace into a 13AMP/230Volt (240V in
Australia) outlet. If the cord does not reach you
may use a 3-core type extension cord rated for a
minimum of 13 AMPS.
4. Push the Fireplace into place so that the trim is
against the finished Mantel Surround or wall
surface. (FIGURE 6)
5. Level, if required with wood shims (not included)
(FIGURE 7).
5
FIGURE 7
FIGURE 6

OPERATION
This section will explain the function of each convenient control.
1. To access the controls, open the upper grill by pulling, near the top right hand side,
forward and down. (FIGURE 9)
2. To locate controls refer to FIGURE 10.
3. To conceal the controls during the operation, return the grill to its original upright
position.
WARNING
Ensure the power cord is not installed so that it is
pinched or against a sharp edge and ensure that
the power cord is stored or secured to avoid
tripping or snagging to reduce the risk of fire,
electric shock or injury to persons.
FIGURE 8
WARNING
The centre and left hand side of the grille will get
hot when the heater is operating. Take care to
always grasp the grille on the right hand side.
FIGURE 9
CAUTION
If you need to continuously reset the heater, unplug
the unit and call your local
dealer.

6
A. MAIN ON/OFF SWITCH
The ON/OFF SWITCH supplies power to all fireplace functions (Heater/Flame).
B. MAIN POWER INDICATOR LIGHT
The main power indicator light will illuminate, confirming the unit is turned ON.
C. FLAME ACTION CONTROL
Turn the flame action control knob to adjust the flame speed to the desired level.
D. FLAME BRIGHTNESS CONTROL
Turn the flame brightness control knob to increase or decrease the brightness of the flame
and embers.
E. LED INDICATORS
Indicates the current function of the fireplace
F. MANUAL SELECTION BUTTONS
To choose between flame effect setting, flame effect with low heat setting, and flame effect
with high heat setting.
G. HEATER THERMOSTAT CONTROL
To adjust the temperature to your individual requirements, turn the thermostat control
clockwise all the way to turn on the heater. When the room reached the desired
temperature, turn the thermostat knob counter clockwise until you hear a click. Leave in
this position to maintain the room temperature at this setting. For additional heat, turn
clockwise until you hear the click again and the heater will turn on.
NOTE:
The heater may emit a slight, harmless odor when first used. This odor is a normal condition
caused by initial heating of internal heater parts and will not occur again.
RESETTING THE TEMPERATURE CUTOFF SWITCH
This unit is equipped with a thermostat, which controls the temperature of the room. It does
this by turning the heater on and off. The heater is protected with a safety device to prevent
overheating. Should the heater overheat, an automatic cut out will turn the heater off and it will
not come back on without being reset. It can be reset by switching the main ON/OFF SWITCH
to OFF and waiting 5 minutes before switching the unit back on.
7
CAUTION
If you need to continuously reset the heater, unplug the unit and call your local dealer.
C D B
A
F
E
G
FIGURE 10