Dimplex EWM-COPPER User manual

PRACTICAL USER’S GUIDE
FOR THE ELECTRIC WALL MOUNTED
FIREPLACE
MODEL NUMBER:
EWM-COPPER
EWM-SS-BLK
Valued Customer,
We are pleased that you have chosen to purchase an electric fireplace
manufactured by Dimplex North America Limited.
7205780200REV00
Quality checked by:

OPERATION
The controls are located on the lower right side of the wall mounted electric fireplace.
(FIGURE 7)
A. MAIN ON/OFF SWITCH
The on/off switch supplies power to all unit functions (heat/flame)
B. HEATER ON/OFF SWITCH
The HEATER ON/OFF SWITCH supplies power to the heater fan and the heater element.
C. HEATER THERMOSTAT CONTROL
To adjust the temperature to your individual requirements, turn the thermostat control
clockwise all the way to turn on the heater. When the room reached the desired
temperature, turn the thermostat knob counter clockwise until you hear a click. Leave in
this position to maintain the room temperature at this setting. For additional heat, turn
clockwise until you hear the click again and the heater will turn on. To turn the heater off,
switch the HEATER ON/OFF SWITCH to the OFF position.
NOTE: When the heater is switched ON, the heater fan will operate. The heater element may
or may not be on, depending on the thermostat control setting (SEE “HEATER THERMOSTAT
CONTROL”).
FIGURE 7 (LOWER RIGHT SIDE)
6

RESETTING THE TEMPERATURE CUTOFF SWITCH
Should the heater overheat, an automatic cut out will turn the heater off and it will not come
back on without being reset. It can be reset by switching the MAIN ON/OFF SWITCH to OFF
and waiting 5 minutes before switching the unit back on.
CAUTION
If you need to continuously reset the heater, unplug the unit and call Dimplex customer service
at 1-888-DIMPLEX (1-888-346-7539).
MAINTENANCE
WARNING
Disconnect power before attempting any maintenance or cleaning to reduce the risk of fire,
electric shock or damage to persons.
LIGHT BULB REPLACEMENT
Allow at least 5 minutes for light bulbs to cool before touching bulbs to avoid accidental burning
of skin.
Light bulbs need to be replaced when you notice a dark section of the flame or when the clarity
and detail of the log exterior disappears. There are two bulbs under the log set which generate
the flames and embers.
TOOL REQUIREMENTS
Slot screw driver
HELPFUL HINTS
It is a good idea to replace all light bulbs at one time if they are close to the end of their rated
life. Group replacement will reduce the number of times you need to open the unit to replace
light bulbs.
LOWER LIGHT BULB REQUIREMENTS
Quantity of 3 – 35 Watt Clear Halogen Lamps, 120 Volt, G9 base. DO NOT EXCEED 35
WATTS PER BULB.
LOWER BULB REPLACEMENT
1. Unplug the unit from the outlet.
2. Remove the two mounting screws from the bottom front
of the heater assembly. (FIGURE 2)
3. Loosen but do not remove the four heater and light
assembly mounting screws located on the bottom sides
of the wall mounted electric fireplace. (FIGURE 2)
4. Slide the heater and light assembly forward to release it
from the bottom of the wall mounted electric fireplace
(FIGURE 1).
5. Place heater and light assembly on a flat surface and
examine the bulbs to determine which bulb(s) required
replacement
6. Remove the burnt out bulb(s) by gently pulling straight
out of socket. If bulbs are difficult to remove from socket
move the bulb from side to side while pulling being
careful not to damage the light socket.
7. Insert new bulb(s).
8. Install the heater and light assembly onto the four
mounting screws.
9. Slide the assembly backwards to lock it into position.
10.Tighten the four heater and light assembly mounting
screws.
11.Install the two front mounting screws.
12.Plug in the wall mounted electric fireplace.
7
FIGURE 1
FIGURE 2

GLASS CLEANING
The front glass is cleaned in the factory during the assembly operation. During shipment,
installation, handling, etc., the front glass may collect dust particles, these can be removed by
dusting lightly with a clean dry cloth.
To remove fingerprints or other marks, the glass can be cleaned with a damp cloth. The glass
should be completely dried with a lint free cloth to prevent water spots. To prevent scratching,
do not use abrasive cleaners or spray liquids on the glass surface.
WALL MOUNTED ELECTRIC FIREPLACE SURFACE CLEANING
To remove fingerprints or other marks, the exterior finish can be cleaned with a damp cloth
with a mild detergent. The surface should be completely dried with a lint free cloth to prevent
water spots.
To prevent scratching, do not use abrasive cleaners or spray liquids on any surface.
8