Discount Car Stereo JAG-HF User manual

Courtesy of: DiscountCarStereo.com
Serving the internet community since 1995
JAG-HF
QUICK START BLUETOTH INSTALLATION GUIDE FOR SELECT JAGUAR XJ & XK WITH CD CHANGER
1998-03 x308 and 1997*-06 x100

PRODUCT SAFETY & DISCLAIMER
READ ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING, FAILURE TO DO SO MAY CAUSE
PERSONAL INJURY OR DAMAGE TO PRODUCT AND/OR PROPERTY
•This installation guide is provided as a GENERAL installation guide, some vehicles vary and
may require additional steps. We do not accept responsibility for third party labor charges
or modifications. Exercise due-diligence when installing this product.
•We do not accept any responsibility for vehicle damage or personal injury resulting from
the installation of this product.
•Careless installation and operation can result in equipment damage.
Requirements:
Functional 6 cd auto changer
Introduction
Safety comes first when you’re on the road, so having an intuitive and easy to
use Bluetooth kit is essential to reducing driver distraction. The JAG-HF kit is
compatible with virtually all Bluetooth phones, and sounds great for mobile
conversations or streaming music. In addition to Bluetooth, the JAG-HF
provides a 3.5mm AUX input which can be used to connect wired devices
such as MP3 Players, iPods, Zune, iPads etc. (AUX input takes the place of
CD changer playback). The built-in USB charging port can be used to charge
devices (1.8A), however for larger current hungry devices (e.g., iPhone 8 and
newer), we recommend adding optional USB-DMA3 “Fast charge” kit. The audio
adapter connects to CD changer plug in trunk or hatch and Bluetooth module
installs beneath center console glove box (armrest).
Warning: The required CD changer remains connected but will no longer
play.
To retain CD changer playback, purchase our JAGCD-HF instead.
See Frequently Asked questions at the end of this guide
Installing audio module
Audio module connects to the CD auto changer connector in trunk/hatch
1. Remove carpet trim piece surrounding audio rack
2. Remove (4) 8mm nuts securing rack to vehicle.
3. Locate cable holder behind audio rack for CD changer single thick black cable
(connects CD changer to amplifier in premium systems and to radio in
standard systems) (See Fig. 1)
Noteworthy: There are similar size/color cables in this area. CD changer
single thick black cable is the correct one.
Fig. 1
4. Remove black cable from holding tab and disconnect by grasping both plugs
and gently pulling apart (do not twist)
5. note Fig. 2- CD changer female connector (right), amplifier/radio plug (left).

Fig. 2
6. Connect factory male plug (See Fig. 2) to module: simply align
marks on factory male plug with that on module female connector
7. Connect module male right-angle plug (See Fig. 3) to CD changer
female connector (See Fig. 2)
Warning: module male right-angle plug does not have marking. To
connect; align mark drawn in Fig. 3 with mark on CD changer connector
(See Fig. 2), Ignoring this warning will cause damage to both plug and
connector.
Fig. 3
Fig. 3a
8. Connect one end of included 16 ft. 3.5mm male-male audio cable to
module AUX jack (See Fig. 4), and route to center console.
Fig. 4

Routing audio cable
1. Use a pry tool to open gap between window pillar and rear deck as seen in
Fig. 5. Go into trunk and fish the audio cable through and into cabin. (See
Fig. 6)
16 ft. Audio Cable
Fig. 5
Fig. 6
2. Pull excess cable and begin tucking under backrest and seat cushion as you
work towards center glove box (armrest) as seen in Fig. 7, Fig. 8 and Fig.
9
Fig. 7
Fig. 8
Fig. 9
3. Continue to use pry tool or fingers to fish cable under center glove box into
storage bin.
4. To remove storage bin: Open the center glove box and remove 2 Philips
head screws from latch cover and two more from hinge then remove the
single screw on retainer bracket.
5. Lift to remove storage bin and set aside.
6. Locate audio plug fed through in step 3 and gently pull excess cable.

Bluetooth module installation
In our test vehicle (2001 XJR Premium Audio), the Bluetooth module was secured
to center armrest sidewall (See Fig. 10) and is our recommendation. In this
area you will also find the factory phone plug and cigar lighter wiring, either of
which can be used to power the Bluetooth module (see Fig. 11).
Warning: Cigar lighter wiring is prone to noise especially if a USB charger is
installed. Locate a noise free power source or purchase a noise filter. In most
instances, this noise is not related to a bad module.
Fig. 10
Fig. 11
Bluetooth module Red wire requires 12V accessory. (Do not connect to
constant battery supply) and Black wire must be grounded.
Factory connector/Plug
Ignition supply wire
Ground wire
10-pin Female (white)
Pin 10 (light green)
Pin 6 (black)
10-pin Male (yellow)
Pin 10 (white/green)
Pin 6 (black)
14-pin (yellow)
Pin 13 (Green)
Pin 11n (black)
18-pin male (yellow)
Pin 5 (Green)
Pin 11 (black)
1. If vehicle does not have a phone plug, simply tap into cigar lighter supply
wires under console: White/Blue= 12V ACC, Black=Ground.
Fig. 12
2. Connect 3.5mm audio plug (routed from trunk) to module pigtail jack (See
Fig. 13)
Fig. 13
Audio out

3. Connect supplied (3ft.) audio cable (See Fig. 14) to module “AUX” input
jack, (See Fig. 15). Route other end to dash area or location where
audio device will reside (within 3ft).
Fig. 14
3ft. audio cable
Fig. 15
Bluetooth module
4. Connect push-button/mic (See Fig. 16) to module “MIC” input (See Fig.
15)
Fig. 16
Control button/Microphone
5. Consider where to install push-button/microphone. Keep in mind the
push-button must be within drivers reach and facing forward for voice
commands and phone dialog (cable is 6ft. long). We recommend
completing the rest of the install prior to securing the
control/mic button to the dash. Once you decide on a location simply
remove tape backing (See Fig. 17) and stick to dash (See Fig. 18)
Fig. 17
Control/Mic button
Fig. 18
Make sure no ventilation duct is pointed towards the mic.
It is best to mount button facing driver

USB charging port
Module USB port is for charging only. Please note this may not provide sufficient
current to charge newer power-hungry devices (e.g., iPhones). If you own one of
these newer devices, consider purchasing our USB-DM3 Smart charging Kit.
You may install the provided USB kit in 1 of 3 ways:
These are also applicable to optional USB Fast Charge Kit.
A. Flush to dash/panel requires drilling a ¾” hole
B. Flush Mount with Support bracket (use this option to mount USB terminal
wherever your installation demands without drilling)
C. Not Mounted- (default)-- Connect your own USB Cable
A. Flush Mount to Dash or Panel (requires drilling)
1. Drill a ¾” hole in the dash or panel using a hole saw, step drill bit or
equivalent (See Fig. 19)
Fig. 19
Step drill bit
2. Insert 3.2ft. (1 Meter) USB male terminal (See Fig. 20) through ¾”
hole created in step 1 and connect to module USB port (See Fig. 21)
Fig. 20
USB cable
Fig. 21
Module USB port
3. Snap USB head to mounting surface until flush (See Fig. 23)
Fig. 22
USB head
Fig. 23
Flush mounted to dash
4. Tuck and secure any extra wire from moving parts
B. Flush mount with Support Bracket (No drilling)
1. Locate a flat surface at location of choice within 3.2 ft. (1 meter) of
module and mount USB support bracket (See Fig. 24) to surface using
adhesive/tape or screws.

Fig. 24
USB mounting bracket
2. Insert USB male terminal through hole in bracket (See Fig. 25) and
connect to USB port on Module (See Fig. 21)
Fig. 25
3. Snap USB head to mounting plate until flush (See Fig. 26)
Fig. 26
4. Tuck and secure any extra wire away from moving
Bluetooth pairing and connection
This process is required the first time you use the JAG-HF. After initial pairing,
the JAG-HF will automatically reconnect with the paired phone upon entering
vehicle.
1. Turn the vehicle ignition to “ON”.
2. Red LED inside module will begin to flash
3. Access Smartphone Bluetooth menu settings, and search (scan) for
devices.
4. Select name listed below and tap “Connect”
Note: Pairs up to 4 phones but connects to one phone at a time.
Warning: Caller ID and text display are not possible on factory Radio. Operate
Bluetooth device by pressing the control button and your Voice Recognition
applications. Use the radio volume button to control playback level

Bluetooth operation
1. Turn ignition to ACC position and radio ON.
2. Press “CD” button on radio. Track or Disc number displayed only if they are
disc in magazine otherwise “NO MAGAZINE” is displayed (See Fig. 27)
Fig. 27
Radio must be in “CD Mode” when using the JAG-HF. CD Changer remains
connected but will no longer play.
3. Use radio button to adjust playback level and tone controls.
Music Commands
To
Proceed this way
Pause a Song
Press and release button
Resume Play
Press and release button
Skip to next song
Press button twice
Skip to Previous Song
Press button three times
Activate Aux input*
Press button four times
Activate Voice Control
Press/hold button for 2 seconds
Switch from Aux to Streaming Audio
Press and release button
Phone Commands
To
Proceed this way
Answer call
Press and release button
End call
Press and release button
Reject incoming call
Press button twice (call goes to VM)
Cancel outgoing call
Press button twice
Activate Voice Control
Press/hold button for 2 seconds
Notes:
1. If audio playback is distorted or low, adjust volume on phone.
2. To reset Module, press and Hold button for 5 seconds (this will not
un-pair phone or erase stored phones)
3. Bluetooth range is approximately 30 ft. make sure device is within
range of receiver
4. Voice command compatible with Apple (Siri), Android (Google Now),
Blackberry (Assistant)
5. *Audio controls not applicable in Aux mode. Use the Aux device built-in
control for music selection and controls.
If successful proceed to reverse the removal steps for Amp rack and center
glovebox console and secure the control button/microphone to dash as per step
#6 in “installing Bluetooth module” instructions.
Congratulations, you’ve just updated your vehicle to support new technology
while preserving the original radio and dash components.
Enjoy!

Frequent ask questions & troubleshooting
1. How to I pair a second phone to module?
In order to pair other phones make sure no other phone is paired to module.
Once first device is unpaired, it will be possible to pair another.
2. Can the JAG-HF be installed without removing the radio?
YES; this kit is designed to be installed without removing radio in both
Premium and Standard Systems.
3. What’s the major difference between the JAGCD-HF and JAG-HF?
The JAGCD-HF requires and retains the CD changer, the JAG-HF requires
but does not retain use of the CD changer. (Changer remains connected
but will no longer play and instead an aux input jack is provided)
4. In which model/year Jaguars will the JAG-HF work and where does
the audio module connect?
1998-03 x308 (To changer)
1997 x100 –with Ai-Net style changer only (To changer)
1998-06 x100 (To changer)
5. Will the stereo mute when calls are made or received?
This system will not mute stereo unless radio is in “CD” mode (Bluetooth
mode). If in AM/FM mode, audio system will not mute. In addition, you must
switch radio to “CD” (Bluetooth Mode).
6. Will I be able to use both music and Navigation apps at the same time?
YES! When streaming audio and Navigation apps, music will mute during
navigation guidance and return to previous state when guidance ends. If a
call is made or received, both Navigation guidance and audio streaming are
muted until the call ends.
7. Which audio devices can I connect to the AUX input?
The 3.5mm aux jack on Bluetooth module supports any audio device with a
3.5mm plug (e.g., iPod, MP3, Satellite radio, etc.).
8. Which devices can be charged from USB charging port?
Any and all Bluetooth 2.0 devices requiring 5V Charge including
smartphones, iPod, iPhones, etc.; however, power hungry devices such as
the new iPhones (8-up) may not charge. If you own one of these power-
hungry phones, purchase optional Fast charger option.
9. There is alternator “whine”. What can I do to fix this?
Check ground wires
make sure all connections are snug
If powering module with cigar lighter, try removing device plugged into
cigar port.
Relocate ground wire
Install a noise filter.
Feature
JAG-HF
JAGCD-HF
BT45-JAG
A2DIY-JAG98
A2DIY-JAG98R
CD changer retention
X
✓
X
✓
✓
Audio input (aux)
✓
✓*
X
Optional
Optional
Charging (USB)
✓
✓
X
Optional
Optional
Mutes (all radio modes)
X
X
✓
X
X
Visor microphone
X
X
✓
✓
✓
Requires CD changer
✓
✓
✓
✓
✓
Voice Recognition
✓
✓
✓
X**
X**
Requires phone plug
X
X
✓
X
X
Plug-n-play installation
X
X
✓
X
X
Smart media button
²
²
✓
✓
✓
Module installs:
Armrest
Armrest
Armrest
Armrest
behind radio
*Aux input instead of CD changer
** activate VR on audio device as customary
² optional remote
Disclaimer
• This product has no affiliation with Jaguar or Apple
• There are no warranties expressed or implied by purchase of this product
• We’re not liable for misuse of this product.
Email [e-mail]
© 1995-Sep-21 Discount Car Stereo, Inc. All rights reserved. Information in this
document is subject to change without notice. Other products and companies referred
to herein are trademarks or registered trademarks of their respective companies or
mark holders.