Displays2go LEDDCP User manual

A
PARTS LIST
A. Frame Module
B. Frame Module with Door
C. Aluminum Bar - Top
D. Aluminum Bar - Mid & Bot X4
X1
E. Side Panel - Clear
F. Side Panel - Black F1
Side Panel - Black F2
G. Top Panel - Clear
H. Bottom Panel - Black
I. LED lighting Panel
J. White Panel
K. Plastic Endcap
L. M3X12 Pointed Screws
M. M4X8 Machine Screws
N. Torx Wrench
O. Power Adapter Charger
X1
X1
X2
X2
X1
X1
X1
X1
X1
X4
X8
X4
X1
X1
IMPORTANT
Read all instructions before assembling the unit. Displays2go is not responsible for any damage or injury
caused by incorrect installation, assembly or use.
B
C
D
E
F
I
J
K
G
432
345
5
1047
346
3
1047
346
3
346
346
5
H
346
346
3
330
330
5
346
346
5
L
N
M
O
ASSEMBLY INSTRUCTIONS
Ver. 10/19
LEDDCP - Illuminated Metal Pedestal
1 of 6
F1
F2

NOTE:
1. Top aluminum bar has T-slot on one side ONLY.
2. Middle and Bottom aluminum bars have T-slot on both sides.
3. Bottom aluminum bar has velcro glued on the bottom.
Top
2 of 6
LEDDCP - Illuminated Metal Pedestal
Alu. Bar-Middle
Alu. Bar-Bottom
-F2 -F1

STEP 2
Insert the Clear Side Panels (E), Black Side Panels (F) to the sides.
Attach Black Bottom Panel (H) to the velcro on the fixed aluminum bars.
Make sure all the panels fit inside grooves and tighten the screws in the aluminum bars that con-
necting with Frame Module (A).
Alu. Bar - Top
Alu. Bar - Top
Frame Module (A)
3 of 6
LEDDCP - Illuminated Metal Pedestal
F1 Side Panel-Black F2
- Middle
- Middle
STEP 1
Place Frame Module (A) on a flat surface. Insert the aluminum bars into the grooves on both sides
of the Frame Module, then fix alu bars by fastening the screws with the wrench (N).
NOTE: DO NOT tighten completely at this point. - Bottom
- Bottom

Frame Module (B)
STEP 3
Connect the Frame Module with Door (B) with the assembled pedestal body. Be sure all the bar
connectors and all panels inserted into the grooves on the Frame Module (B).
Secure the Frame by tightening all screws in the aluminum bars that connecting with Frame Module
with Door (B).
Tips: Open the door with included keys and tighten the screws on the middle bar.
4 of 6
LEDDCP - Illuminated Metal Pedestal

STEP 4
Carefully lift the assembled pedestal to its stand-
ing position.
Open the door on the pedestal and connect the
DC wire inside the pedestal with the wire at the
bottom of the LED Lighting Panel (I). Place the
LED panel on the brackets.
Fix the LED panel by tighening M4X8 Machine
screws (M) at 4 corners.
STEP 5
Place the White Panel (J) above the LED lighting
Panel as shown below:
5 of 6
LEDDCP - Illuminated Metal Pedestal

Scan QR code to visit the product page:
STEP 6
Place the Top Panel (G) on the top of the pedestal.
Fix the endcaps (K) at 4 top corners by using M3X12 pointed screws (L).
Plug in the power adapter (O) to charge and power the unit. Turn on the switch and the assembly is
finished.
If you have any questions regarding our products, please visit us at www.displays2go.com or contact D2G
customer service at 844-221-3388.
6 of 6
LEDDCP - Illuminated Metal Pedestal