Displays2go SMAWRDCSC User manual

A. Top Wooden Panel H. M6 Screw (16)
B. Wooden Pole (4)
C. Acrylic Shelves - Large (8)
I. M4 Screw - Short (32)
J. M4 Screw - Long (3)
D. Acrylic Shelves - Small (8)
E. Wooden Plate - Bottom
F. Rotating Plate
G. Wooden Base
2 people are required
V20.09
ASSEMBLY INSTRUCTIONS
SMAWRDCSC - Countertop Rotating Display
PARTS LIST:
A. Wooden Panel - Top
B. Wooden Pole
C. Acrylic Shelf - Large
D. Acrylic Shelf - Small
E. Wooden Panel - Bottom
F. Rotating Plate (mounted on G)
G. Wooden Base
HARDWARE:
H. M6 Screw
I. M4 Screw - Short
J. M4 Screw - Long
Qty.
1
4
8
8
1
1
1
16
32
3
If you have any questions regarding our products, please visit us at www.displays2go.com
or contact D2G customer service 844-221-3388.
1 of 2
Please read these instructions carefully before assembling the product.

STEP 1. Place the Top Wooden Panel (A) on top of 1 Wooden Pole
(B) and align the holes on the pole with the pre-drilled holes at 1
corner of the panel. Insert 2 M6 Screws (H) through holes on the
panel and tighten them to connect the pole.
Repeat the step to connect the remaining poles with the top panel.
STEP 2. Hold the poles and the top panel, and carefully turn the
assembled frame upside down.
Attach Bottom Wooden Panel (E) to the open end of the poles and
secure it using 8 M6 Screws (H).
A
B
H
TOP EH
NOTE:
a. The countersink side of the
bottom panel must face up.
b. Keep the assembled frame
in current position until STEP
4 is finished.
STEP 3. Place the Wooden Base (G) on the floor upside down.
Rotate the base to align the through hole on the wooden base with 1 hole on the Rotating plate (F). Insert 1 M4 Screw - Long (J) through
the hole and let it rest on the rotating plate.
STEP 4. Lift the base up and place it onto the assembled frame.
Align the inserted M4 screw on the round plate with 1 screw hole on
the bottom panel and screw it into the bottom panel.
NOTE: DO NOT TIGHTEN THE SCREW! DOING SO MAY BREAK
THE ROTATING PLATE!
Rotate the wooden base and align remaining holes on the rotating
plate with the corresponding screw holes. Insert 1 M4 screw (long) at
a time and screw it into the hole without tightening.
STEP 5. Carefully place the assembled unit on its standing position.
Assemble Small Shelves (D) and Large Shelves (C) onto the display
body with M4 screws - Short (I).
NOTE: DO NOT assemble the same sized acrylic shelves on
adjacent sides of the display.
G
J
F
Small Shelf
(D)
Small Shelf
(D)
Large Shelf
(C)
Large Shelf
(C)
M4 Screw
NOTE:
a. The countersink side of the
top panel must face up. (see
detailed view)
b. One end of the pole labeled
with “TOP” must face up.
c. The sides that have screw
holes on each pole must face
outside.
DO NOT OVER-TIGHTEN
SCREWS!
DO NOT USE POWER
TOOL!
NOTE: Maintain an even amount of
force across 3 screws when fastening.
ASSEMBLY INSTRUCTIONS
SMAWRDCSC - Countertop Rotating Display
2 of 2