Displays2go LTMLT2AV1 User manual

-8-
Thank you for choosing our product
This product contains small items that could be a choking hazard if swallowed. Keep
these items away from young children!
1.Make sure these instructions are read and completely understood before attempting
installation. If you are unsure of any part of this installation, contact a professional
installer for assistance.
2.The wall or mounting surface must be capable of supporting the combined weight of
the mount and the display; otherwise the structure must be reinforced.
3.Safety gear and proper tools must be used. A minimum of two people are required
for this installation. Failure to use safety gear can result in property damage, serious
injury or death.
Warning
INSTALLATION GUIDE
TV Size Range: 10"~27"
Max load capacity of each TV plate:
8Kg/17.64lbs
Integrated Cable management
CAUTION
Please read this guide before installation.
Ensure the correct installation. Keep away from high frequency or power equipment to
avoid disturbance.Choose desk to put this product.
We can not be responsible for any damage caused by wrong installation.
Item No.:LTMLT2AV1

Hardware Kit:
ID Description
1
4
C
5
A
3
6
B
1
2
1
2
2
2
M4×12mm bolt
M5×12mm bolt
Qty
8
8
AB
Tube Cover
M4X10mm bolt
TV plate
Knob
Slid block
Fixed wreath
7
10
8
11
9
12
2
1
2
1
1
2
Tighten block
Cable cover
Tube
2
Botton support
Hand handle
2
M5x10mm sunk bolt
Washer
(Φ8.5xΦ16x0.8)
D23X3,4X4Wrench
1
4
C
5
3
67
10
89
11
2
12
D
-7-
-2-
13
14
15
E
13
14
15
4
1
Mat feet
Bottom plate
1Nut
E16X6Wrench

-3-
-6-
4
C
1
2
2
5
5
8
6
7
Picture 1
C
1
First install the plastic cover, then fixed the wreath(6) on the tube by
M5x10mm sunk bolt(7). Once the wreath fixed, then slide the TV plate into
the tube and fixed it by knob(4). When fixed wreath and TV plate are
installed, put on the tube cover(1) and use (C) by wrench(D) to make it
tighten.( picture 1)
Part 1-Install TV plate and fixed wreath
67
NOTE:
D(3X3mm)
Part 4-Fitting the bottom plate(13) on the desk[If you don’t want to use
bottom support(11)]
12
13
12
DESKDESK
first, take off screw M6X10 and M10X20 by wrench,then remove the whole
bottom support(11) to change bottom plate(13),tighten screwing 4pcs of
M6X10,then stick 4pcs mat feet(14) to the screws,see the fig.3. After that,
put the screw nut on the proper position of knob.The last step, make the
Hand handle(12) get through the desk and then make nut tighten by wrench.
14
Fig.1 Fig.2
Fig.3 Fig.4
E(6X6mm)
D(4X4mm)

-5-
-4-
( picture 3)
Part 2-Fitting the bottom support on the desk
Choose the position of the base you want installed. Make sure there is
enough space to spread display considering the show size.The desk should
between 15mm and 55mm thick and strong enough to bear the force caused
by your display.( picture 2)
DESK
( picture 2)
A,B
CABLE
Part 3-Attaching TV plate to screen
Center TV plate on back of the screen and align the eight mounting holes.
Select screws(A,B). Attach TV plate to screen using eight selected screws
(A,B). Tighten screws firmly. Do not overtighten.( picture 3)