Displays2go WXNTVGBO1 User manual

1. Install (6) pointed feet (E) into the
base (U) from the bottom.
Dx1
C
Rx4 Bx4 Ax4
2. Align tapped holes in the extrustion () with pre-drilled holes in the
base (U), with an end plate (D) in between these 2 parts. Secure the
extrusion by using (4) screws (A), (4) washers (B) and (4) rubber wash-
ers (R). See part numbers shown below. A second person may be
required to help with the assembly.
PLEASE READ THESE INSTRUCTIONS COMPLETELY AND MAKE SURE YOU ARE COMFORTABLE
WITH THE INSTALLATION PROCESS. ALSO CHECK YOUR TV’S USER MANUAL TO SEE IF THERE ARE
ANY SPECIAL REQUIREMENTS FOR MOUNTING YOUR TV.
WARNING:
1. Max Weight: 110 lbs. It is the installer’s responsibility to make sure that the weight of the display monitor
does not exceed 110 lbs.
2. Use this TV stand only for its intended use as described in these instructions. Displays2go is not responsi-
ble for damage or injury caused by incorrect assembly or use.
3. A remote control or toys placed on the glass shelf may encourage children to climb onto the TV stand and
as a result the TV stand may tip over and fall onto the children. Serious injury or death may occur.
Two people are recommended to assemble the product.
If you do not understand these instructions or have questions about the safety of the installation, assembly or
use of this product, please contact DISPLAYS2GO Customer Service at 1-800-572-2194.
COMPONENT AND HARDWARE
A. Screw M8X33mm
B. Washer_L ID=8.4mm
C. Hex Key M6
D. End Plate
E. Pointed Foot
F. Bracket_shelf
G. Bracket_1_shelf
H. Bracket_2_shelf
I. Extrusion
J. Hex Key M4
K. Slide-in T-nut
L. Screw M8X16mm
X4
X4
X1
X2
X6
X1
X1
X1
X1
X1
X1
X6
M. Hex Key M5
N. Washer_S ID=8.4mm
O. Square Plate
P. TV Plate
Q. Cup Nut
R. Rubber Washer
S. Screw M8X14mm
T. Adapter Bracket
T1. Adapter Bracket
U. Base
V. Glass Shelf
X1
X8
X1
X1
X4
X8
X4
X1
X1
X1
X1
WXNTVGBO1 - TV STAND WITH GLASS SHELF
1 of 2

T T1
M
G H
F
J
Lx2 K
3. Assemble both supporting brackets (G) and (H)
with center bracket (F) by using hex key (J). Slide the
T-nut (K) down the T-slot from the top of the extrusion
(). Align corresponding holes on both parts, and affix
the assembled shelf bracket securely to the desired
height with (2) screws (L).
4. Attach the square plate (O) to the top of the extru-
sion () with (1) end plate (D) in the middle by fasten-
ing (4) screws (L) and (4) washers (N).
O
Dx1 M
Lx4
Nx4
5. Assemble TV plate (P) with the square plate mount-
ed in Step 4 by using Part (S), (N), (R) and (Q), (4) of
each.
6. Slide adapter brackets (T) and (T1) from left and
right respectively. See the picture below.
Qx4
Rx4
Nx4
Sx4
P
7. Carefully place the glass shelf (V) onto the support-
ing brackets assembled in Step 3. Adjust the height as
needed.
8. Safely lift the TV and attach the back of TV to the
brackets (T) and (T1). Secure the brackets by tighten-
ing the screw located at the bottom of each bracket.
2 of 2
V