DivioTec TBR721 User manual

Quick Installation Guide Ver.A (P/N: 60177B0320X00)
Accessories DI/DO Pin Denition & Waterproof Connector Description
DI/DO & Function Description
Placement sticker
Dehumidier
packet
Quick guide
3-axis cable concealed
wall mount bracket
Waterproof
connector
Wall mount
base
Mounting accessory
kit
DI/DO POWER
5 4 3 2 1 2 1
Gasket
Tightening
collar Waterproof
connector
Seal nut
Strain relief
Main body
q
w
e r t
PHONE
JACK
RJ45
MB Module
DI/DO
1 ALM_IN (+)
2 ALM_IN (-)
3 ALM_out_NC
4 ALM_out_COM
5 ALM_out_NO
POWER
1 AC24V/DC12V (+)
2 AC24V/DC12V (-)
Cable Wiring Description
Cable Installation Steps:
1. Run the cable inside the wall mount bracket and out through
the cable opening at the front.
2. Wire the network cables to the waterproof connector on the
right, and wire the line-in, line-out, DC 12V/AV 24V, DI/DO
and other cables to the waterproof connector on the left.
Tighten the waterproof connector after all the cables are
secured in place.
3. Secure the camera onto the wall mount bracket using the
four screws provided. Unscrew the 2 screws on the camera's
top cover at the side in preparation for the next step.
4. Open the camera's top cover to access the wired cables.
Install the RJ45 connector to the Ethernet cable and plug it
into the corresponding port on the MB module.
5. Close the camera's top cover and secure it with the supplied
hardware tool to complete.
SB Module MB Module
8 PCS LED IR
Illuminator
Board Plate
Dehumidier
Packet
Line-out Line-in Ethernet / PoE
Micro SD
DI/DO Reset
Default
DC 12V/
AC 24V
Heater module
55ORotate
180ORotate
360ORotate

Quick Installation Guide Ver.A (P/N: 60177B0320X00)
3. Wire the required cables through the cable opening on the front of the wall mount bracket. Then,
attach and secure the wall mount bracket to the wall mount plate with two M5 screws. Next, install
the waterproof connectors onto the cables on the front of the wall mount bracket.
5. Secure the top cover to nish the installation.
Cable Outlet Description
Hardware Installation
1. The camera features two waterproof connectors,
the right one in the diagram is for PoE connection,
while the left one is for line-in, line-out, DC 12V/
AC 24V and DI/DO connections.
2. The left one features four wire holes. Please
cover unused holes with sealing plugs to prevent
water from entering.
3. Applicable cable diameter:
* Ø 1.8~2.5mm (Left)
* Ø 4.7~6.9mm (Right)
4. Secure the camera to the wall mount bracket with the four screws and hex wrench. Open the
camera’s cover and connect the cables to their corresponding ports on the MB module. Then, glue
the dehumidier packet onto the metal bracket using the adhesive sticker on its back, as depicted
in the diagram below. Quickly close the camera’s cover and ensure the clip is locked in position to
prevent the dehumidier packet from losing its effectiveness.
Line-out
Line-in
DC 12V/AC 24V
DI/DO
Ethernet/
POE
Dehumidier
packet
1. Position the placement sticker at the desired installation location and use a driller to drill the holes
on the sticker.
2. Insert three screw anchors into the holes then place the wall mount base on top of them with the
mounting holes aligned.

Quick Installation Guide Ver.A (P/N: 60177B0320X00)
3-axis Angle Adjustment
1. The vertical tilt angle of the camera can be adjusted up or down within an angle of 55°. Loosen
the left and right screws depicted below to adjust the vertical tilt angle and then tighten the screws
after nishing the adjustment.
2. The horizontal tilt angle of the camera can be adjusted left or right within an angle of 180°. Loosen
the left and right screws depicted below to adjust the horizontal tilt angle and then tighten the
screws after nishing the adjustment.
3. The rotatable axis can be rotated in 360°. Loosen the left and right screws depicted below to
adjust the 360-degree position and then tighten the screws after nishing the adjustment.
1. Locate and open the Internet Explorer (IE) shortcut on the desktop.
2. In the address bar, type 192.168.0.250 (default IP address of the camera) and then press the
Enter button.
3. You will be prompted with a pop-up window asking for login information, type in “Admin” (default
login name) and “1234” (default password).
Accessing the Web GUI Login through Web Browser (Internet Explorer)
55° Rotate
180° Rotate
360° Rotate