Divus TOUCHZONE TZ07 User manual

DIVUS TOUCHZONE . 1
Technical Manual
DIVUS
TOUCHZONE
TZ07-TZ10-15”-TZ19
Version DTZ2.15-3.2 06/17

DIVUS TOUCHZONE . 2
GENERAL INFORMATION
DIVUS GmbH
Pillhof 51
I-39057 Eppan (BZ)
Operating instructions, manuals and software are protected by copyright. All rights are reserved. Copying, multi-
plication, translation and conversion, either partially or as a whole, is not permitted. You are allowed to make a
single copy for backup purposes.
We reserve the right to make changes to the manual without prior notification.
We assume no responsibility for any errors or omissions that may appear in this document.
We do not assume liability for the flawlessness and correctness of the programs and data contained on the de-
livered discs.
You are always welcome to inform us of errors or make suggestions for improving the program.
The present agreement also applies to special appendices to the manual.
This manual can contain terms and descriptions, which improper use by third can harm the copyrights of the
author.
Please read the manual before beginning and keep the manual for later use.
The manual has been conceived and written for users who are experienced in the use of PCs and automation
technology.
This version of the manual is based on the following version(s):
-TOUCHZONE image R2.15
-TOUCHZONE image R3.2
-DIVUS LAUNCHER v. 1.1.3 rev. 115
-DIVUS VIDEOPHONE (1.0) v. 1.0.1 rev. 65
-DIVUS VIDEOPHONE 4 v. 4.1.0 rev. 89
-DIVUS OPTIMA v. 1.1.1 rev. 82
-DIVUS KIBRO v. 1.2.1 rev. 16
-DIVUS MÜLLPLANER v. 1.0 rev. 9
-DIVUS IP CAM VIEWER v. 1.0 rev. 10
-DIVUS SCREENCLEANER v. 1.0.1 rev. 9

DIVUS TOUCHZONE . 3
Through most of the manual the Android version 4.2.2 isused in screenshots and examples. Android version 5.0.2
will be discussed in a separate chapter.

DIVUS TOUCHZONE . 4
CONVENTIONS
DIVUS DIVUS
[KEYS]
Keys that are to be pressed by the user are given in square brackets, e.g. [CTRL] or [DEL]
COURIER
On-screen messages are given in the Courier font, e.g. C:\>
COURIER BOLD
Keyboard input to be made by the user are given in Courier bold, e.g. C:\>DIR).
Names of buttons to be pressed, menus or other onscreen elements and product names are
given within double quotes.
PICTOGRAMS
In this manual the following symbolic are used to indicate particular text blocs.
Caution!
A dangerous situation may arise that may cause damage to material.
Hint
Hints and additional notes
New
New features

DIVUS TOUCHZONE . 5
SAFETY INSTRUCTIONS
The present operating instructions contain those safety instructions that are required to safely operate the ma-
chine.
All persons working with the machine must heed the present operating instructions, especially the safety in-
structions.
In addition, all local stipulations governing the prevention of accidents must be heeded.
Only trained and authorized personnel may INSTALL AND OPERATE the machine.
PROPER APPLICATION: The machine has been designed for application inside the building automation and
must not be used to control security functions.
The machine has been built using state-of-the-art technology and all applicable safety regulations. However,
damage or negative effects to the machine or other material cannot be excluded if the machine is operated.
The machine meets the requirements of the EMC guidelines and of the harmonized European standards. Modifi-
Without special protection measures, the machine must not be used in EX areas and in plants that require spe-
cial monitoring.
Danger of explosion. Do not expose the buffer batteries to heat. Serious injury may be the result.
The operating voltage of the machine must be within the specified range! The product label provides the re-
quired information.

DIVUS TOUCHZONE . 6
STANDARDS
The DIVUS TOUCHZONE meets the following guidelines and standards:
Low Voltage Directive 2014/35/EU (ex 73/23/CEE 93/68/CEE 06/95/CE)
Standard to which conformity is declared:
EN 50491-3:2009, EN 60950-1:2006+A11:2009+A1:2010+A12:2011 Safety
EMC Directive 2014/30/EU (ex 89/336/CEE 92/31/CEE 93/68/CEE 04/108/CE)
Standard(s) to which conformity is declared:
EN 50491-5-1:2010, EN 50491-5-2:2010 Conducted & Radiated Emissions
RoHS2 Directive 2011/65/EU (ex 02/95/EC)
Standard(s) to which conformity is declared:
EN 50581:2012 Restriction of hazardous substances
The installation and wiring instructions contained in this documentation must be heeded. Conformity is indicated
by the attached CE label.
The EC conformity statements can be obtained from:
DIVUS GmbH
Pillhof 51
I-39057 Eppan (BZ)
Regarding Directive 2012/19/EU (ex 2002/96/EC) waste electrical and electronic equipment
has to be collected separately and is not allowed to dispose as unsorted municipal waste.

DIVUS TOUCHZONE . 7
INDEX
1PRODUCT DESCRIPTION ________________________________________________________________________9
1.1 FRONT VIEW DIVUS TOUCHZONE ___________________________________________________________9
1.2 INTERFACES DIVUS TOUCHZONE___________________________________________________________10
1.2.1 REAR CONNECTIONS:__________________________________________________________________10
1.2.1.1 DIO______________________________________________________________________________11
1.2.1.2 DC IN ____________________________________________________________________________12
1.2.2 FRONT CONNECTIONS _________________________________________________________________13
1.3 PRODUCT CONTENTS_______________________________________________________________________14
2COMMISSIONING______________________________________________________________________________15
2.1 GROUNDING _______________________________________________________________________________15
2.2 COMMISSIONING ___________________________________________________________________________15
2.3 INSTALLING THE DIVUS TOUCHZONE_________________________________________________________16
3OPERATING SYSTEM___________________________________________________________________________17
3.1 FEATURES _________________________________________________________________________________19
3.2 HARDWARE INTERFACES____________________________________________________________________20
3.3 GOOGLE PLAY STORE_______________________________________________________________________20
3.4 DIVUS LAUNCHER__________________________________________________________________________21
3.4.1 INTRODUCTION _______________________________________________________________________21
3.4.2 _________________________________________________________________25
3.4.3 ___________________________________________________________________28
3.4.4 ____________________________________________________34
3.4.5 ________________________________________________________________41
3.5 DIVUS OPTIMA _____________________________________________________________________________45
3.6 DIVUS VIDEOPHONE ________________________________________________________________________50
3.7 DIVUS VIDEOPHONE 4 ______________________________________________________________________51

DIVUS TOUCHZONE . 8
3.8 DIVUS KIBRO_______________________________________________________________________________52
3.9 DIVUS MÜLLPLANER________________________________________________________________________55
3.10 DIVUS IP CAM VIEWER___________________________________________________________________59
3.11 DIVUS SCREENCLEANER _________________________________________________________________65
3.12 TEAMVIEWER QUICKSUPPORT ____________________________________________________________66
3.13 SYSTEM UPDATE ________________________________________________________________________67
4ANDROID 5.0.2 - LOLLIPOP_____________________________________________________________________68
4.1 PRE-INSTALLED APPS_______________________________________________________________________68
4.2 WI-FI SUPPORT_____________________________________________________________________________68
4.3 NETWORK SETTINGS________________________________________________________________________69
4.4 FUTURE UPDATES OF ANDROID 5.0.2 ________________________________________________________69
5TECHNICAL DATA _____________________________________________________________________________70
5.1 MECHANICAL DATA ________________________________________________________________________70
5.2 DIVUS TOUCHZONE DATA OVERVIEW ________________________________________________________71
5.3 DIVUS TOUCHZONE WALL MOUNT BOX ______________________________________________________72
5.4 MAINTENANCE AND UPKEEP ________________________________________________________________77
6APPENDIX ____________________________________________________________________________________78
6.1 RECYCLING INFORMATION __________________________________________________________________78

DIVUS TOUCHZONE . 9
1Product description
1.1 FRONT VIEW DIVUS TOUCHZONE
DIVUS TOUCHZONE
TZ10 portrait mode TZ15 landscape mode
TZ07 portrait TZ10 TZ15 TZ19 landscape mode size comparison

DIVUS TOUCHZONE . 10
1.2 INTERFACES DIVUS TOUCHZONE
1.2.1 REAR CONNECTIONS:
The DIVUS TOUCHZONE has various connection possibilities on its back side. All necessary interfaces can be
found there.
ATTENTION! Only the TZ07, TZ10 and TZ15 versions support PoE+. The TZ19 version must be powered through
the DC in port.
ATTENTION! Although the TZ07, TZ10 and TZ15 versions support hybrid power supply by PoE+ and DC in at the
same time, only one power input should be used at a time.
Rear Connections:
-DIO (digital inputs/outputs)
-DC in
-USB1
-USB2
-LINE Out
-LAN PoE+
-S1
-S2

DIVUS TOUCHZONE . 11
1.2.1.1 DIO

DIVUS TOUCHZONE . 12
The digital ouputs are driven by low 3,3V voltage with 1,75mA current. To be able to use the digital output to
switch any kind of load a relay-module with transistor pre-amplifier is required; an example schematic of a
connected transistor pre-amplified relay-module is shown below.
ATTENTION! The componentsof such a transistor pre-amplified relay-module vary depending from the used power
supply and manufacturer.
NOTE: Please always remember that the ports are DIGITAL in- and outputs! Their exact specifications can be found
in the table below. Furthermore it is recommended that both in- and outputs are always connected through a
relay circuit.
Voltage output HIGH
(= on)
3,3 V
Voltage input HIGH
(= on)
1,65 3,6 V
Voltage output LOW
(= off)
0 V
Voltage input LOW
(= off)
0 V
Output current
1,75 mA
1.2.1.2 DC IN

DIVUS TOUCHZONE . 13
1.2.2 FRONT CONNECTIONS
DIVUS TOUCHZONE offers important front connections for sensing and expansion too.
1. Microphone
2. USB OTG
3. MICRO SDHC card slot
4. POWER button
5. RGB LED
6. HOME button
7. Loudspeaker
NOTE: with applied design cover, only the touchscreen and the HOME button are available while operating the
device. Moreover you can use the soft keys, which are shown in the navigation bar of DIVUS TZ.

DIVUS TOUCHZONE . 14
1.3 PRODUCT CONTENTS
Hardware:
-DIVUS TOUCHZONE
-Fixing set to be used with a wall mount kit
-Retention screws
-Aluminum front cover
Software:
-Pre-Installed, fully functional operating system
Documentation:
-Technical manual
-Quick Start Guide
-Warranty conditions
-Version overview

DIVUS TOUCHZONE . 15
2Commissioning
2.1 GROUNDING
The following must be heeded to ensure that all electrical interference is safely absorbed:
-Connect the metallic wall mount kit with a central grounding point using the shortest possible distance.
-Make sure that the connection between the unit and the grounding point has the lowest possible
impedance.
-All data cables connected to the unit must be shielded.
-The shields must be groundedat both ends. A low-impedance connection must be established between
the linked units. High compensation currents over the cable shields caused by potential differences
must be excluded.
-Use a green-yellow cable with a minimum cross section of 2,5mm² for ground connection.
2.2 COMMISSIONING
The power supply of the TOUCHZONE is provided (PoE) - IEEE 802.3at -
(TZ07, TZ10 and TZ15) or through the DC input on DC in plug (TZ07, TZ10, TZ15 and TZ19). Using DC input, the
used power supply needs to provide safety extra-low voltage (SELV) and has to be compliant to EN60950-1
par.2.5 and EN61558-2-6 or equivalent. The TZ07 and TZ10 versions must be powered through a supply providing
max. 15 VA under normal operating conditions. For all versions you must have the means for disconnection
incorporated in the fixed wiring. Have the appliance connected to the mains using a device that allows the
appliance to be disconnected from the mains at all poles with a contact opening. If using PoE+, ensure that your
switch, injector or power adapter is fully PoE+ compliant.
Power consumption of the device is defined in the technical documents.
ATTENTION! Pull out the power plug before opening the unit. Check all cable connections before commissioning
the system. Make sure that all voltages and signals meet the specifications.
ATTENTION! Only the TZ07, TZ10 and TZ15 version support PoE+, the TZ19 version must be powered through DC
in.
ATTENTION! Although the TZ07, TZ10 and TZ15 versions support hybrid power supply by both PoE+ and DC in at
the same time, only one power input should be used at a time.
NOTE: DIVUS offers a warranty of24 months after shipment (valid fromthe date of delivery) if not stated otherwise
for the DIVUS TOUCHZONE. The warranty is only valid if all transportation takes place with the original package of
the product, including all shock absorbing elements.

DIVUS TOUCHZONE . 16
Every repair shipment has to be approved by the technical support. Contact us under [e-mail]. On that
occasion you also get all necessary information, as well as the accompanying letter "repair request".
The original packaging has to be used for all transportations, including the one back to the distributor or
manufacturer in case of arantee for the product. Any damage occurring
to the product if incorrectly packed will be charged to the client. Furthermore in such a case DIVUS will charge
an additional fee for packing.
document has to be compiled and returned with the product to allow
us to guarantee an efficient service and a two week repair time.
For technical reasons only complete products can be returned for repair.
2.3 INSTALLING THE DIVUS TOUCHZONE
Installing wall mount kit
The wall mount box may be installed in a cut out in the wall, in a wooden structure thick at least 1.5 cm or in a
drywall construction. The cut out has to respect the sizes specified in the technical data and has to be at least 8
cm deep.
In the wall cut out, the box can be built in or it can be screwed on in a piece of furniture. It is important that the
fore edge of the wall mount kit is flat and horizontally to the surface of the wall or the piece of furniture.
The wall mount kit offers cable access on all four sides.
Installing TZ
Switch off the system/plant supply voltage. Connect the power and controlling cables. After connecting the
magnet to the back of the mount box, the TZ is put into the wall mount box and is fixed with the screws included
in the packing. Now, you can install your design frame with slight, even pressure.
ATTENTION! Unauthorized changes or modifications to the TZ configuration may result in permanent damage to
the system or its functionality. Only authorized trained personnel are allowed to make any modifications.
ATTENTION! If you need to remove the design frame, extract it from the mounting horizontally. One-sided traction
or slanted installing may damage the frame.
ATTENTION! In order to be able to dissipate the warmth produced by the equipment, it must be guaranteed that
the temperature within the mounting box does not exceed 45°C. Under normal conditions this is given with an
ambient temperature of up to 30°C. If these values are exceeded, additional cooling has to be provided.
The equipment must be installed vertically, i.e. the front plate must be in an angle of 90° to the base plate.
Installation has to comply to HD 60364-4-41 or other national prescriptions.

DIVUS TOUCHZONE . 17
3Operating System
DIVUS TOUCHZONE is delivered with the Android operating system in version 4.2.2. This operating system, used
on countless smartphones and tablets, offers nearly ungated capabilities and possibilities through its Open Source
core and all the manufacturer-specific applications. General information about the Android operating system can
be found under www.android.com.
NOTE: The Android operating system 5.0.2 and its differences will be discussed in a separate chapter.
Beneath the standard applications delivered by the default operating system (for example gallery, music player,
), the following applications are installed by DIVUS:
-Google Play Store (previously known as Android Market)
-DIVUS LAUNCHER
-DIVUS OPTIMA
-DIVUS VIDEOPHONE
-DIVUS VIDEOPHONE 4
-DIVUS KIBRO
-DIVUS MÜLLPLANER
-DIVUS IP CAM VIEWER
-DIVUS HEARTBEAT
-DIVUS SCREENCLEANER
-System-Update
-TeamViewer QuickSupport
The single applications are explained in more details in the following chapters.
NOTE: Most of the screenshots shown within this manual are coming from devices in LANDSCAPE mode; the
PORTRAIT mode typically offers the very same functionality, changes are limited to the graphical layout.
As in the previous version, also the new TZ series offers a navigation bar at the bottom of the display, which
should simplify and fasten the navigation on the device. Beneath the HOME button, this navigation bar contains
all the soft keys required for the navigation within the Android system. Find below a screenshot of the navigation
bar:

DIVUS TOUCHZONE . 18
The 6 keys within the navigation bar from left to right are:
-VOLUME DOWN
-BACK
-HOME
-RECENTS
-VOLUME UP
-MENU
The VOLUME DOWN key lowers the volume of the DIVUS TZ and shows the current volume through a
corresponding slider element, which also permits to access further volume settings.
The BACK key (depending on the shown app) permits to return to the previously shown page or to close the
currently opened app.
The HOME key has the same functionality as the hardware HOME button and brings you back to the first page of
the DIVUS LAUNCHER. The previously active app is brought to the background and continues running (the HOME
button / key does NOT terminate running apps).
If the HOME key is pressed for a longer time, depending on the configuration, additional actions (e.g. the access
to Google NOW) become available.
A click on the RECENTS key shows the recently opened apps, which allows a quick switching between different
applications and via swipe gesture also the closure of apps.
The VOLUME UPkey increases the volume of the DIVUS TZ and like the VOLUME DOWN key shows the current
volume through a corresponding slider element, which also permits to access further volume settings.
The MENU key functionality depends on the currently shown app and if available shows additional menu and
configuration options. The following screenshot shows an example of such a menu:

DIVUS TOUCHZONE . 19
Furthermore, also the MENU key supports long-clicking: in this case it will show another pop-up window which
permits to turn off or reboot the DIVUS TZ:
ATTENTION! Please ALWAYS use this menu in order to shutdown DIVUS TZ. An abrupt removal of the power
supply can interrupt running processes and cause the malfunction of different apps.
3.1 FEATURES
The pre-installed DIVUS apps provide the user with various functions to control its TOUCHZONE and home
automations system. These features include, among others:
-Customization and configuration of the DIVUS TOUCHZONE.
-Access and control over the installed apps.
-Pre-installed DIVUS OPTIMA app for building automation.
-Pre-installed DIVUS VIDEOPHONE app for interaction with intercom systems
-Pre-installed DIVUS KIBRO app for internet navigation
-Pre-installed DIVUS MÜLLPLANER app to manage household waste.
-Pre-installed DIVUS IP CAM VIEWER app to visualize IP cameras.
-Pre-installed DIVUS HEARTBEAT app, used to access reports of DIVUS HEARTBEAT.
-Pre-installed DIVUS SCREENSCLEANER app, used during screen cleaning
In order to get the new features, please check that your DIVUS TZ has loaded the latest software version. An
update of your DIVUS TZ to the latest operating system version can be requested using the following form:
http://www.divus.eu/index.php/en/softwareupdate-divus-touchzone
The single apps instead can also be updated directly through the Google Play Store (therefore all the new features
can be obtained simply by updating the apps through the Play Store). If your account is correctly registered, you
should automatically get a notification when new versions are available.

DIVUS TOUCHZONE . 20
3.2 HARDWARE INTERFACES
DIVUS TZ offers different kinds of interfaces as well on the rear as on the front side. All interfaces are integrated
and functional on Android level and can be accessed from custom applications through corresponding libraries.
The following list shows the interfaces currently used by the applications of DIVUS, as well as the interfaces
currently free and therefore usable in custom apps. In case you should need the function libraries for your own
customizations, please refer to the technical support of DIVUS:
Front side:
-Microphone: Among others used by the DIVUS VIDEOPHONE app.
-USB-OTG: Works as well as USB host as also as USB device, which means that either USB
devices (like USB storages, USB mice etc.) can be connected or DIVUS TZ can be used as mass storage
on a PC.
-MicroSD card slot: Through the settings of DIVUS LAUNCHER connected microSD cards can be
mounted/unmounted.
-RGB-LED:Is used by the DIVUS LAUNCHER for signalling purposes.
-Speaker: Among others used by the DIVUS VIDEOPHONE app.
Rear side:
-DIO: Among others used by the DIVUS VIDEOPHONE app.
-USB1+2: For the connection of USB devices (like USB storages, USB mice etc.).
-Line out: Can be used to forward the audio signal to a HIFI system (internal audio signal is
disabled)
NOTE: USB SUPPORT: Generally all USB devices compatible with Linux operating systems that are using the default
drivers (HID devices, mass storages) can be used in combination with DIVUS TZ.
3.3 GOOGLE PLAY STORE
Additional apps can be installed through various means, one of them is the Google Play Store. Details on the first
steps with the Google Play Store can be found on the following web page:
http://support.google.com/googleplay/?hl=en