Divus TZ07-B?TZ07-W User manual

Technical Manual
English
Deutsch
Version DT1.3
–
01/13

- English Version Page E1 - Page E41
- Deutsche Version Seite D1 - Seite D41
- Recycling Information Page I
CONTENTS OF MANUAL

TZ07-B, TZ07-W
E-1
English Version

TZ07-B, TZ07-W
E-2
GENERAL INFORMATION
DIVUS GmbH
Pillhof 51
I-39057 Eppan (BZ)
Operating instructions, manuals and software are protected by copyright. All rights are reserved. Copying,
multiplication, translation and conversion, either partially or as a whole, is not permitted. You are allowed to
make a single copy for backup purposes.
We reserve the right to make changes to the manual without prior notification.
We assume no responsibility for any errors or omissions that may appear in this document.
We do not assume liability for the flawlessness and correctness of the programs and data contained on the
delivered discs.
You are always welcome to inform us of errors or make suggestions for improving the program.
The present agreement also applies to special appendices to the manual.
This manual can contain terms and descriptions, which improper use by third can harm the copyrights of the
author.
Please read the manual before beginning and keep the manual for later use.
The manual has been conceived and written for users who are experienced in the use of PCs and automation
technology.
C ONVENTIONS
[KEY] Keys that are to be pressed by the user are given in square brackets, e.g. [CTRL] or
[DEL]
Courier On-screen messages are given in the Courier font, e.g. C:\>
Courier bold input to be made by the user are given in Courier bold, e.g. C:\>DIR).
„…“(double quotes) Names of buttons to be pressed, menus or other onscreen elements and product
names are given within double quotes. (e.g. “Configuration”).
Symbolic In this manual the following symbolic are used to indicate particular text blocks.
Caution!
A dangerous situation may arise that may cause damage to material.
Note.
Hint and additional notes

TZ07-B, TZ07-W
E-3
SAFETY INSTRUCTIONS
The present operating instructions contain those safety instructions that are required to safely operate the
machine.
All persons working with the machine must heed the present operating instructions, especially the safety
instructions.
In addition, all local stipulations governing the prevention of accidents must be heeded.
Only trained and authorized personnel may install and operate the machine.
Proper application: The machine has been designed for application in an industrial environment.
The machine has been built using state-of-the-art technology and all applicable safety regulations. However,
damage or negative effects to the machine or other material cannot be excluded if the machine is operated.
The machine meets the requirements of the EMC guidelines and of the harmonized European standards.
Modifications to the machine hardware may affect the system’s EMC compatibility.
Without special protection measures, the machine must not be used in EX areas and in plants that require
special monitoring.
Danger of explosion. Do not expose the buffer batteries to heat. Serious injury may be the result.
The operating voltage of the machine must be within the specified range! The product label provides the
required information.
STANDARD
DIVUS TOUCHZONE meets the following guidelines and standards:
Low Voltage Directive 2006/95/CE (ex 73/23/CEE – 93/68/CEE)
Standard to which conformity is declared:
EN 60950-1: 2001-02 Safety
EMC Directive 2004/108/CE (ex 89/336/CEE – 92/31/CEE – 93/68/CEE)
Standard(s) to which conformity is declared:
Emissions:
EN 61000-6-3 :2002-10
EN 55022:1999 (+A1:2001) Conducted & Radiated Emissions
Immunity:
EN 61000-6-1 :2002-10
EN 61000-4-2: 1996 (+A1:1998,+A2:2001) Electrostatic Discharges
EN 61000-4-4: 1996 (+A1:2001,+A2:2002) Electrical Fast Transient / Burst
EN 61000-4-5: 1997 (+A1:2001) Surge
EN 61000-4-11: 1997(+A1:2001) DIPS & Voltage Variations
EN 61000-4-6: 1997(+A1:2001) Conducted RF
EN 61000-4-3: 1997(+A1:1999,+ A2:2001) RF Electromagnetic Field
EN 61000-4-3: 1997(+A1:1999,+A1:2001) 50 Hz Magnetic Field
The installation and wiring instructions contained in this documentation must be heeded. Conformity is
indicated by the attached CE label.
The EC conformity statements can be obtained from:
DIVUS GmbH
Pillhof 51
I-39057 Eppan (BZ)
Regarding DIRECTIVE 2002/96/EC waste electrical and electronic equipment
has to be collected separately and is not allowed to dispose as unsorted
municipal waste.

TZ07-B, TZ07-W
E-4
CONTENTS
GENERAL INFORMATION 2
SAFETY INSTRUCTIONS 3
STANDARD 3
CONTENTS 4
A. PRODUCT DESCRIPTION 5
A1. FRONT VIEW -DIVUS TOUCHZONE 5
A2. INTERFACES -DIVUS TOUCHZONE 6
A3. SCOPE OF DELIVERY 9
B. COMMISSIONING 9
B1. GROUNDING 9
B2. COMMISSIONING 9
B3. INSTALLING THE DIVUS TOUCHZONE 10
C. OPERATING SYSTEM 11
C1 HARDWARE INTERFACES: 13
C2 GOOGLE PLAY STORE: 14
C3 DIVUS LAUNCHER: 14
C4 DIVUS OPTIMA: 24
C5 DIVUS VIDEOPHONE: 28
C6 RECOVERY: 36
D. TECHNICAL DATA 37
D1. MECHANICAL DATA 37
D2. DIVUS TOUCHZONE DATA OVERVIEW 38
D3. DIVUS TOUCHZONE WALL MOUNT BOX 39
D4. MAINTENANCE AND UPKEEP 41

TZ07-B, TZ07-W
E-5
A. PRODUCT DESCRIPTION
A1. Front view - DIVUS TOUCHZONE
●DIVUS TOUCHZONE
Ima
g
e:
T
Z07 with Frame
T
Z07 side-view mounted
Ima
g
e:
T
Z07 horizontal mountin
g

TZ07-B, TZ07-W
E-6
A2. Interfaces - DIVUS TOUCHZONE
Rear connections
DIVUS TOUCHZONE has various connection possibilities on his back side. All necessary interfaces can be
found there.
RS232/285
Rear Connections:
-RS232/285
-DIO
-DCin
-USB1
-USB2
-LINE Out
-LAN – PoE
-S1
-S2

TZ07-B, TZ07-W
E-7
DIO
DCIN

TZ07-B, TZ07-W
E-8
Front connections
DIVUS TOUCHZONE offers important front connections for sensing and expansion too.
1. BACK-button
2. Microphone
3. Temperature sensor
4. Light sensor
5. USB OTG
6. Micro SDHC card slot
7. RGB LED
8. HOME button
9. IR receiver
10. POWER button
11. loudspeaker
Note: with applied design cover, only the touchscreen and the HOME button are available for the
handling of the device. The interface of DIVUS TZ was designed in a way that this input methods are
enough. If you have own applications that require the BACK button, you can find it as hidden button
under the design cover. In alternative you can use the soft keys, which are shown in the navigation
bar of DIVUS TZ.
Note: further information regarding the interfaces and their control can be found in chapter C1.
1/3 2 4 5 6 7 8 9 10 112 4 7 8 9 11

TZ07-B, TZ07-W
E-9
A3. Scope of delivery
Hardware:
DIVUS TOUCHZONE
Fixing set to be used with wall mount kit
Retention screw
Aluminum front cover
Recovery-microSD
Software:
Pre-Installed, fully functional operating system
Documentation:
Technical manual
Warrantee conditions
Note: Please refer to chapter C of this manual which contains important information about the
installation of the OS.
B. COMMISSIONING
B1. Grounding
The following must be heeded to ensure that all electrical interference is safely absorbed:
Connect the metallic wall mount kit with a central grounding point using the shortest possible distance.
Make sure that the connection between the unit and the grounding point has the lowest possible impedance.
All data cables connected to the unit must be shielded.
The shields must be grounded at both ends. A low-impedance connection must be established between the
linked units. High compensation currents over the cable shields caused by potential differences must be
excluded.
Use a green-yellow cable with a minimum cross section of 2,5mm² for ground connection.
B2. Commissioning
Power supply of TOUCHZONE is granted or through “Power over Ethernet” or through DC input on DCin
plug. If using PoE ensure that your switch, injector or power adapter is fully PoE compliant.
Power consumption of the device is defined in the technical documents.
More technical details of the power supply can be found in section D2.
Caution!
Pull out the power plug before opening the unit. Check all cable connections before
commissioning the system. Make sure that all voltages and signals meet the specifications.

TZ07-B, TZ07-W
E-10
Note: Warranty regulations
DIVUS guarantees for DIVUS TOUCHZONE a warranty of 24 months after shipment (valid from
date of delivery) if not stated otherwise. The warranty is only valid if all transportation takes place
with the original package, including all shock absorbing elements, of the product.
Every repair shipment has to be approved by the technical support. Contact us under support @ divus.biz.
On that occasion you also get all necessary information, as well as the accompanying letter "repair request".
The original packaging has to be used for all transportations, as well for the one back to the distributor or
manufacturer (like for repair). Otherwise DIVUS can’t give any guarantee for the product. Any damage
occurring to the product if incorrectly packed will be charged to the client. Furthermore in such a case DIVUS
will charge an additional fee for packing.
For repair processes the document “repair request” has to be compiled and returned with the product to
allow us to guarantee an efficient service and a two week repair time.
For technical reasons only complete products can be returned to reparation.
B3. Installing the DIVUS TOUCHZONE
Installing wall mount kit
The wall mount box may be installed in a cut out in the wall, in a wooden structure thick at least 1,5 cm or in
a dry mortarless construction. The cut out has to respect the sizes specified in the technical data and has to
be at least 8 cm deep.
In the wall cut out, the box can become build in while it can be screwed on in a piece of furniture. It is
important that the fore edge of the wall mount kit is flat and horizontally to the surface of the wall or the
piece of furniture.
The wall mount kit offers cable access at all four sides.
Installing TZ
Switch off the system/plant supply voltage. Connect the power and controlling cables. After the correct
cabling and connecting the magnet, the TZ is put into the wall mount box and is fixed with the screw
included in the packing. Now, you can install your design frame with slight, even pressure.
Caution!
Unauthorized changes or modifications to the TZ configuration may result in permanent damage to
the system or its functionality. Only authorized trained personnel are allowed to make any
modifications.
Caution!
If you need to remove the design frame, extract it from the mounting horizontally. One-sided
traction or slanted installing can damage the frame.
Caution!
In order to be able to dissipate the warmth produced by the equipment, it must be guaranteed, that
the temperature within the mounting box does not exceed 45°C. Under normal conditions this is
given with an ambient temperature of up to 30°C. If these values are exceeded, additional cooling
has to be provided.
The equipment must be installed vertically, i.e. the front plate must be in an angle of 90° to the base
plate.

TZ07-B, TZ07-W
E-11
C. O PERATING S YSTEM
DIVUS TOUCHZONE is delivered with the Android operating system in version 2.3.4. This operating system,
used on countless smartphones and tablets, thanks to the Open Source technology offers nearly ungated
capabilities as well as numerous usage possibilities dues to the availability of manufacturer-specific
applications. General information about the Android operating system can be found under
www.android.com.
Beneath the standard applications delivered by the default operating system (for example gallery, music
player,…), the following applications are installed by DIVUS:
-Google Play Store (previously known as Android Market)
-DIVUS LAUNCHER
-DIVUS OPTIMA
-DIVUS VIDEOPHONE
The single applications are explained more in details in the following chapters.
Compared to traditional Android systems with version 2.3.4, the version customized by DIVUS offers a
navigation bar at the bottom of the display (similar to the bar of Android 4.x), which should simplify and
fasten the navigation on the device. Find below a screenshot of the navigation bar:
The 3 keys within the navigation bar are (from left to right):
-BACK
-HOME
-MENU
The BACK key in its functionality corresponds to the hardware BACK button (check out chapter A2) and –
depending on the active app – permits to return on the previously shown page or to close the corresponding
app.
The HOME key has the same functionality as the hardware HOME button and brings you back to the first
page of the DIVUS LAUNCHER. The previously active app in this moment is brought to the background and
continues running (the HOME button / key do NOT terminate running apps).
If the HOME key is pressed some longer time, a pop-up window showing the recently opened apps will
appear. This allows a quick switching between different applications.
The MENU key functionality depends on the currently shown app and – if available – shows additional menu
and configuration options. The following screenshot shows an example of such a menu:

TZ07-B, TZ07-W
E-12
Furthermore, also the MENU key supports long-clicking: in this case it will show another pop-up window
which permits to turn off or reboot DIVUS TZ:
CAUTION: Please ALWAYS use this menu in order to shutdown DIVUS TZ. An abrupt removal
of the power supply can interrupt running processes and cause the dysfunction of different
apps.
NEWS - VERSION 2013:
Since January 2013 as well new versions of the base image as also of the consequently described apps are
available. The most important changes are listed below:
GENERAL:
-Wi-Fi base support (only in combination with the Wi-Fi module of DIVUS)
-Navigation bar can now be shown / hidden through menu
-Improvement of the system stability
-General Android bug fixing
-RecoverySD now executes also a file system check
DIVUS LAUNCHER (vers. 0.9 rev.9):
-Integration of an automatic brightness control
-Integration of a version page
-Improvement of the landscape mode
DIVUS OPTIMA (vers. 0.9 rev.6):
-Extension of the layout support for additional resolutions / Android devices
-Smaller graphical adaptions
-Introduction of a version page
-Bug fixing: Remote access now automatically uses SSL protection
DIVUS VIDEOPHONE (vers. 0.9 rev.11):
-It is now possible to define 2 video signals for each external unit; in the main window it is possible to
change between the video signals using a swipe gesture
-The video signal is now automatically shown also on outgoing calls
-The sub menu „External units“ has been transformed into „Phone book“ and now permits to
configure also up to 20 internal units (beneath the 10 external units)
-For each external unit a ringtone and a display name can be configured
-The internal units can also be connected to a ringtone and a display name, furthermore it is possible
to assign them an image file, shown at incoming calls

TZ07-B, TZ07-W
E-13
-For both external and internal units it is possible to define QuickDial buttons which are shown in the
dial window of the app
-The SIP port (default 5060) can now be changed
-It is possible to enable a forced re-registration after a definable time period (is required by some
VoIP servers)
-Extension of the layout support for additional resolutions / Android devices
-Smaller graphical adaption (like introduction of images during incoming / outgoing calls)
-Introduction of a version page
Please check that your DIVUS TZ has loaded the latest software versions. An update of your DIVUS TZ to the
latest operating system version can be requested using the following form:
http://www.divus.eu/index.php?option=com_chronocontact&Itemid=333&lang=en
The single apps instead can also be updated directly through the Google Play Store. If your account is
correctly registered, you should automatically get a notification when new versions are available.
C1 Hardware interfaces:
As already seen in chapter A2, DIVUS TZ offers different kinds of interfaces as well on the rear as on the front
side. All interfaces are integrated and functional on Android level and can be accessed from custom
applications through corresponding libraries. The following list shows the interfaces currently used by the
applications of DIVUS, as well as the interfaces currently free and therefore usable in custom apps. In case
you should need the function libraries for your own customizations, please refer to the technical support of
DIVUS:
Front side:
-Temperature sensor Free, values can be accessed through library
-Brightness sensor Is used by the DIVUS LAUNCHER for automatic brightness control
-Microphone Among others used by the DIVUS VIDEOPHONE app
-USB-OTG Works as well as USB host as also as USB device, which means that either
USB devices (like USB storages, USB mice etc.) can be connected or
DIVUS TZ can be used as mass storage on a PC.
(check out http://www.usb.org/developers/onthego/ )
-microSD card slot Through the settings of DIVUS LAUNCHER connected microSD cards
can be mounted / unmounted
-RGB-LED Is used by the DIVUS LAUNCHER for signaling purposes
-IR sensor Free, can be controlled through library
-Speaker Among others used by the DIVUS VIDEOPHONE App
Rear side:
-RS232/RS485 Free, can be controlled through library
-DIO Free, can be controlled through library
-USB1+2 For the connection of USB devices (like USB storages, USB mice etc.)
-Line Out Can be used to forward the audio signal to a HiFi system (internal audio
signal is disabled)
Note: USB support
Generally all USB devices compatible with Linux operating systems that are using the default
drivers (HID devices, mass storages) can be used in combination with DIVUS TZ.

TZ07-B, TZ07-W
E-14
C2 Google Play Store:
At delivery, DIVUS TZ already contains the Play Store of Google, which can be used to obtain numerous apps
of different manufacturers. This „door“ to the Android world gives you the possibility to customize DIVUS TZ
exactly according to your wishes and to download different kinds of applications to your device. Details on
the first steps with the Google Play Store can be found on the following web page:
http://support.google.com/googleplay/?hl=en
Notes regarding the use of the Play Store on DIVUS TZ:
1. The Play Store requires an active internet connection. If DIVUS TZ is used without internet access, The
Play Store is either automatically hidden or shows a corresponding warning message.
2. In order to be able to use the Play Store, you have to check that your DIVUS TZ shows the correct
date and time settings. If these settings are not correct, the Play Store can not connect to its servers
and will show no contents. The time/date settings can be configured through the settings page of
the DIVUS LAUNCHER.
3. In case no app download should be possible, please empty the cache of the Play Store through the
settings of the DIVUS LAUNCHER (Manage Applications – All – Google Play Store).
4. Please take care that you will not be able to install all apps on the Play Store on DIVUS TZ. The Play
Store is filtering apps according to certain criteria (for example display size, permissions, additional
functions like gravity sensor, GPS, phone etc.). If a device doesn’t support a required criterion, the
app will not be shown on Play Store. So if you shouldn’t be able to see an app on DIVUS TZ that on
your smartphone is visualised normally, it could be that DIVUS TZ doesn’t fulfill one of the criteria
required by the app to be launched correctly. In this case you can try to get in contact with the
manufacturer of the app in order to understand the missing criteria and eventually find a solution for
being able to run the app on DIVUS TZ.
Caution!
The Play Store can only be used with a valid Google-Account. If needed, this account can be created
directly on DIVUS TZ using the wizard within the Play Store. Please note that in Android the first
account created on a device is used as default account and can only be deleted by executing a
FACTORY RESET of Android itself (please check out chapter C6). Further accounts can be created
and deleted without any problems; only the default account requires a factory reset of the device
and therefore is connected to the loss of all previously configured data!
C3 DIVUS LAUNCHER:
The DIVUS LAUNCHER app is the main app of DIVUS TZ. Launcher apps in the Android world generally
determine start screens or graphical interfaces that hide the original menu of Android. In this way the user
should not be overwhelmed by the open architecture of Android, but should be able to focus on the most
important functionalities.
Exactly this concept is followed also by the DIVUS LAUNCHER app, which shows a simple grid of 6 fields that
permit a quick access to the most important functions / apps. Naturally it is possible to create more than one
launcher page, with the possibility to change between them using a swipe gesture. Furthermore the DIVUS
LAUNCHER offers also a series of settings which should make easier the configuration of DIVUS TZ.

TZ07-B, TZ07-W
E-15
After the first start of DIVUS TZ, the DIVUS LAUNCHER will present the following start screen:
The welcome message, as displayed also within the message itself, will be shown as long as the default
password that protects the access to the settings page (0000) isn’t changed. By confirming the message you
will see the first page of the launcher, which is already preconfigured:
Building: Launches the app DIVUS OPTIMA
Intercom: Launches the app DIVUS VIDEOPHONE
Multiroom: Only icon, no app connected
Energy: Only icon, no app connected
Security: Only icon, no app connected
Play Store: Launches the Google Play Store
The fields „Multiroom“, „Energy“ and „Security“ at delivery aren’t configured except the icon and therefore
still must be connected to an app using the long-click-function. It’s the same with the other pages of the
launcher; also their fields are empty. A simple click on an empty / not connected field shows an info message
that the field must first be connected to an app via long-click-function before it can be used. If therefore a
long click is executed on one of the fields, a list of the apps present in the device will be shown, which gives
the possibility to select the desired app and connect it to the field. The selected app in the connection will be
shown at the corresponding position in the launcher. Naturally the long click can be executed also on already
connected fields in order to remove the connected app or to connect a different app.
As visible also in the screenshot above, the first 5 fields use customized icons. Other fields will simply show
the icon of the connected app. If also the first 5 fields should show the original icons instead of the
customized ones, this can be simply acquired by changing the corresponding parameters in the settings
page of the launcher.
The settings page is accessed by clicking on the DIVUS – Logo in the upper bar of the launcher. If the
password protection is active, you will have to insert a password before (like 0000 at first access).

TZ07-B, TZ07-W
E-16
The configuration page offers the settings shown in the screenshot below; in this window it is possible to
scroll vertically in order to access all of the settings:
The following pages will explain the different configuration possibilities. The first to entries simply redirect to
standard Android settings and allow to change the language of DIVUS TZ and to set the date and time
correctly:
DIVUS TZ offers all the languages contained in the Android repertoire. Nevertheless, the 3 applications of
DIVUS are limited to the languages German, Italian and English. If another language is selected, those
applications will be shown in English.
The date and time settings can be configured as well manually as also automatically via network and are
necessary if you want to use the Play Store. It is recommended to use the manual configuration, since
Android limits the synchronization on mobile networks not present on DIVUS TZ.

TZ07-B, TZ07-W
E-17
The next entry deals with the network settings of DIVUS TZ:
DIVUS TZ supports as well the use of a static IP address as also the usage of DHCP. Depending on your
network, these parameters must be configured correctly in order to connect DIVUS TZ with your network and
also with the internet (check out the screenshot in the middle, which shows the configuration menu for the
LAN port). If you are unsure about the correct configuration, please refer to your network administrator.
Furthermore this menu in the last version supports also the configuration of the optional Wi-Fi module
offered by DIVUS. If this module is connected to TZ, the menu will automatically show an additional entry
“Wi-Fi” and you will be able to switch between the different connections (Ethernet and Wi-Fi). A parallel
usage of both interfaces is not supported. After enabling the Wi-Fi port, a click on “Network configuration”
will not point to the menu shown above in the middle, but will open the default Android Wi-Fi settings page
(check out screenshot on the upper right).
In the last version of the Launcher-App, this menu will also show the current IP address of DIVUS TZ.
Note: When the connection has been established correctly, in the upper right corner of this
configuration page a green symbol showing 2 PCs will be shown. Only when this symbol is active,
the DIVUS TZ is correctly connected to your network.
The next 2 settings refer to the control of the RGB-LED of DIVUS TZ. The first option permits to use the blue
LED as orientation LED. When the checkbox is enabled, the LED will be continuously on and can be seen as
operating LED or as orientation LED by night.
The second option instead handles the control of the red LED and uses it to signal the current network state.
If DIVUS TZ is not connected to a network and the checkbox of this option is enabled, the red LED will be
turned on. As soon as the device connects to the network, the LED will turn off. Therefore, the option
„Network-Check LED“ acts in the same way as the symbol of the network connection described in the note
above. Naturally, by disabling the corresponding checkbox, also this functionality can be disabled.

TZ07-B, TZ07-W
E-18
The next entry permits to change the design of the DIVUS LAUNCHER. The launcher offers 4 designs /
orientations:
-Black Portrait
-Black Landscape
-White Portrait
-White Landscape
At delivery, the design will already be set according to the order information, through this popup window it
will be possible to change it also in a second moment.
The following screenshot shows an example of the launcher with the design „White Landscape“:
The following to entries of the configuration window allow a further customization of the launcher: