DIY Security Cameras Hikvision User manual

DIY Security Cameras
Hikvision
Intercom Setup Guide
September 2017
Prepared by
DIY Security Cameras
23rd September 2017

Hikvision Intercom Setup Guide (v1.0) September 2017
DIY Security Cameras (www.diysecuritycameras.com.au) Page 2
Contents
2INTRODUCTION .......................................................................................................................................................... 3
3EQUIPMENT .................................................................................................................................................................. 3
4PRE-REQUISITES ......................................................................................................................................................... 3
4.1NETWORK WORKSHEET ............................................................................................................................................ 3
4.2FIRMWARE ................................................................................................................................................................ 3
4.3IVMS4200 SOFTWARE ............................................................................................................................................. 3
4.4PC/LAPTOP ............................................................................................................................................................ 3
5CONFIGURE IVMS4200 SOFTWARE ....................................................................................................................... 4
6ACTIVATE INTERCOM DEVICES ........................................................................................................................... 6
6.1DOOR STATION ......................................................................................................................................................... 7
6.2INDOOR STATION ...................................................................................................................................................... 9
7ASSIGN IP ADDRESS TO INTERCOM DEVICES ................................................................................................ 12
7.1DOOR STATION ....................................................................................................................................................... 12
7.2INDOOR STATION .................................................................................................................................................... 14
7CONFIGURATION AND SETUP OF INTERCOM DEVICES .............................................................................. 17
7.1DOOR STATION ....................................................................................................................................................... 17
7.2MASTER INDOOR STATION ...................................................................................................................................... 20
7.3EXTENSION INDOOR STATION ................................................................................................................................. 23
8VALIDATION .............................................................................................................................................................. 25

Hikvision Intercom Setup Guide (v1.0) September 2017
DIY Security Cameras (www.diysecuritycameras.com.au) Page 3
2 Introduction
This guide will take you through the steps to setup a Hikvision Video Intercom system for a single dwelling with 2 x Indoor
Room Stations and 1 x Villa Door Station. This assumes that the Intercom devices are at factory default settings and need to
be activated.
3 Equipment
1 x KAD606 – Video/Audio Distributor
2 x DS-KH8301-WT – Indoor WiFi station
1 x DS-KV8102-IM – Villa Door Station
1 x PC/Laptop running iVMS4200 2.4.5.X
4 Pre-Requisites
4.1 Network Worksheet
Before we begin we need to plan out our network IP addresses to be assigned to each of the intercom components to provide
connectivity. Any IP subnet can be used, however note that there can only be a maximum of 9 villa door stations in one
system, so leave enough address space to cater for this if required.
In our example we are going to use 192.168.20.0/24 subnet as per the table below.
Device
Type
Local IP Subnet Mask Gateway Door Station
IP
SIP Server Main Door
Type
Main Door V Series 192.168.20.100 255.255.255.0 192.168.20.254 N/A N/A V Series
Master Indoor
Station
Indoor
Station 192.168.20.110 255.255.255.0 192.168.20.254 192.168.20.100 192.168.20.100 N/A
Extension
Indoor Station
Extension
Station 192.168.20.111 255.255.255.0 192.168.20.254 N/A N/A 192.168.20.110
4.2 Firmware
The minimum firmware release for the intercom system is v1.4.0 Build 170302. Please ensure this version of firmware is
installed before proceeding with the remaining setup. To obtain the firmware please email us at
[e-mail]. Note we can only supply firmware to our customers.
4.3 iVMS4200 Software
You will need to install the iVMS4200 software version 2.4.2.55 build161209 onto your laptop. This is required for this
version of the firmware.
4.4 PC/LAPTOP
A Windows PC/Laptop is required to run the iVMS4200 software to programme and setup the Intercom system. The PC in
our example should be connected directly to the KAD LAN2 port. Initially the default factory IP address for the Intercom
devices are: 192.0.0.64/24 (255.255.255.0) and 192.0.0.65/24 (255.255.255.0)
To allow the PC to communicate with the Intercom devices, configured the PC with a primary IP address of 192.168.20.150
(in our example) and a secondary IP address of 192.0.0.250. If you are not sure how to setup a secondary IP address, Google
is your friend.

Hikvision Intercom Setup Guide (v1.0) September 2017
DIY Security Cameras (www.diysecuritycameras.com.au) Page
4
5 Configure iVMS4200 Software
The iVMS4200 (version 2.4) software by default only shows Intercom door stations. To setup and configure Indoor stations
the device type needs to be added to iVMS4200.
1. Click on Device Management.
2. Click on “Add New Device Type”
3. Select “Indoor Station/Master Station” and click OK
4. You should now see “Indoor Station/Master Station” in the left hand menu.

Hikvision Intercom Setup Guide (v1.0) September 2017
DIY Security Cameras (www.diysecuritycameras.com.au) Page
5

Hikvision Intercom Setup Guide (v1.0) September 2017
DIY Security Cameras (www.diysecuritycameras.com.au) Page
6
6 Activate Intercom Devices
All Intercom devices need to be activated (ie with a strong password) before being configured for use. Activation can be
done via the iVMS4200 software tool.
Notes around the activation password
a. Please make this a strong password.
b. The activation password is the main admin configuration/setup password.
c. This password is need to do any configuration on the Intercom devices via the iVMS4200 software.
d. This password is different to the indoor station “admin” password, which can be set separately.
Plug in all the Intercom devices as per above diagram and they will booted up and power on. When powered on they will
appear at the bottom in “Online Devices” section of the iVMS4200 software.

Hikvision Intercom Setup Guide (v1.0) September 2017
DIY Security Cameras (www.diysecuritycameras.com.au) Page
7
Now we activate the devices individually.
6.1 Door Station
1. Select Encoding Device/Door Station
2. Select Door Station at the bottom of the screen and click “Activate”

Hikvision Intercom Setup Guide (v1.0) September 2017
DIY Security Cameras (www.diysecuritycameras.com.au) Page
8
3. Enter a strong password for the door station and click “OK”
4. Device should now show as active.

Hikvision Intercom Setup Guide (v1.0) September 2017
DIY Security Cameras (www.diysecuritycameras.com.au) Page
9
6.2 Indoor Station
1. Select Indoor Station/Master Station in left Menu
2. Select Indoor Station at the bottom of the screen and click “Activate”

Hikvision Intercom Setup Guide (v1.0) September 2017
DIY Security Cameras (www.diysecuritycameras.com.au) Page
10
3. Enter a strong password for the indoor station and click “OK”.
4. Device should now show as active

Hikvision Intercom Setup Guide (v1.0) September 2017
DIY Security Cameras (www.diysecuritycameras.com.au) Page
11
5. Repeat steps 2 and 3 for the remaining Indoor Stations until all show as active.

Hikvision Intercom Setup Guide (v1.0) September 2017
DIY Security Cameras (www.diysecuritycameras.com.au) Page
12
7 Assign IP Address to Intercom Devices
As per our Network Worksheet in section 4.1 assign the IP address, netmask, gateway IP to each Intercom device.
7.1 Door Station
1. Select Encoding Device/Door Station
2. Select Door Station at the bottom of the screen and click “Modify NetInfo”

Hikvision Intercom Setup Guide (v1.0) September 2017
DIY Security Cameras (www.diysecuritycameras.com.au) Page
13
3. Enter IP address, Netmask, Gateway and activation password. Click “OK”
4. Device should now show with the new assigned IP address.

Hikvision Intercom Setup Guide (v1.0) September 2017
DIY Security Cameras (www.diysecuritycameras.com.au) Page
14
7.2 Indoor Station
Note: All indoor stations will have the same default IP address of 192.0.0.64. If you require a particular Indoor Station to be
the Master, then plug the Indoor Station in one at a time and assign the IP address to it. You could also assign the IP address
based on the serial number in the iVMS4200 device display.
1. Select Indoor Station/Master Station
2. Select one Indoor Station at the bottom of the screen and click “Modify NetInfo”.

Hikvision Intercom Setup Guide (v1.0) September 2017
DIY Security Cameras (www.diysecuritycameras.com.au) Page
15
3. Enter IP address, Netmask, Gateway and activation password.
4. Device should now show with the new assigned IP address
5. Now select the remaining Indoor Station and repeat steps 2 and 3 above. After completing all Indoor stations
should show their new IP addresses as per below.

Hikvision Intercom Setup Guide (v1.0) September 2017
DIY Security Cameras (www.diysecuritycameras.com.au) Page
16

Hikvision Intercom Setup Guide (v1.0) September 2017
DIY Security Cameras (www.diysecuritycameras.com.au) Page
17
7 Configuration and Setup of Intercom Devices
We have successfully activated all our devices and assigned IP addresses. We are now ready to add the devices to the
iVMS4200 software client and configure each individual component. The following section will configure each Intercom
device as per our worksheet details in 4.1. Important things to note in our configuration:
a. The Door Station provides our SIP server.
b. The Door Station provides our time synchronisation.
c. The Door Station is linked to the Master Indoor Station.
d. The Master Indoor Station then links to any Extension Indoor Stations within the system.
e. To use the Hik-Connect app the Master Indoor Station MUST have a WiFi option.
7.1 Door Station
1. Select Encoding Device/Door Station and click “Add to Client”
2. In the popup box enter Nickname, admin as the user id and the admin password, and click add.
3. If successful the door station should now appear in the “Device for Management” section ready for
configuration.

Hikvision Intercom Setup Guide (v1.0) September 2017
DIY Security Cameras (www.diysecuritycameras.com.au) Page
18
4. Highlight the “MainDoor” device just added and click on “Remote Configuration”.
5. Navigate to System->Time. Setup the time using NTP. Note the Door Station is responsible to keep our time
synchronised. In our example we use the gateway address because it is an NTP server, however your setup
may vary. Note the NTP server must be entered as an IP address and not a domain name. If unsure you can
use public NTP servers like Google (time.google.com / 216.239.35.12).
6. Select “Enable DST” and set the appropriate start/end time and DST bias.
7. Click Save and the Synchronization.

Hikvision Intercom Setup Guide (v1.0) September 2017
DIY Security Cameras (www.diysecuritycameras.com.au) Page
19
8. Navigate to Intercom->Id Configuration. Set Device Type to “Door Station (V series)”. All other parameters
can be left at defaults. Note “No:” 0 indicates a Master/Main Door Station. Click save.
9. Navigate to Intercom->Dial. Set “Room No:” to 1 and click Save. This is the room number we use for our
master indoor station.
10. Our Door Station is now configured, Close the configuration window by clicking on the X.

Hikvision Intercom Setup Guide (v1.0) September 2017
DIY Security Cameras (www.diysecuritycameras.com.au) Page
20
7.2 Master Indoor Station
1. Select Indoor Station/Master Station and click “Add to Client”
2. In the popup box enter Nickname, admin as the user id and the admin password, and click Add. Repeat for the
remaining indoor stations.
3. If successful the indoor station should now appear in “Device for Management" section ready for
configuration.
4. Highlight the “Master” device just added and click on “Remote Configuration”.