DKS 1520 series User manual

DKSModel1520PrinttoPC
TheseinstructionswillallowyoutoconnectaPCtotheDKS1520stand‐aloneaccesscontrollerprinter
terminalssothatreportingfunctionsinthe1520canbeprinteddirectlytothePCscreen.Youwillhaveto
downloadandinstallserialprinteremulationsoftwareonyourPC,whichwillcreateatextfileofthe
informationreceivedfromthe1520.
1.Software
Downloadandinstalloneofthefollowingprograms(theyareallfree).
•Hyper‐Terminal
•TeraTermPro
•SerialReceptor
5 34 12
89 67
9
10
11
1
3
2
4
6
5
7
12
8
16
17
13
14
18
15
Pin 1Pin 5
Pin 9 Pin 6
DB-9 Female
Pin 2
Pin 4
Pin 5
DB 9
Pin 1520 Term
2
4
5
9
11
10
1520 Terminals
2.ConnectaDB‐9RS‐232C(serialcable)to
the1520.
•ThefemaleendconnectstothePC.
Cutoffthemaleendifnecessaryand
wireasshown.
•CannotuseDoorKing1818‐040cable
becausePin4intheDB‐9connector
isnotwired.
3.PlugtheDB‐9cableintoanavailable
serialportonthePC.
•YoucanalsoplugintoaUSBslotby
usingaUSBtoRS‐232adapter
(DoorKingP/N1815‐037).


4.Powerupthe1520andstartthesoftwareprogramonyourPC.Youwillneedtoselectthe
appropriateCOMportinthesoftwareandsetasfollows.
•BaudRate:9600
•Data: 8Bit
•Parity: None
•StopBit: 1
•FlowControl:Hardware
5.Usethe1520PrintFunctionscommandstodisplaytheinformationrequestedonthePCscreen.
1520PrinttoPC Rev6‐11

1520PrintFunctions
•Refertothe1520Owner’sManual(P/N1520‐065)formoreinformation.
1520KeypadEntryPrintFunction
*22+MasterCodePrintsallCARDcodescurrentlystoredinthe1520memory.
*06+MasterCodePrintsallFACILITYcodescurrentlystoredinthe1520memory.
*40+MasterCodePrintsTIMEZONEinformationcurrentlystoredinthe1520memory.
*32+MasterCodePrintsthecurrentDATEandTIME.
*02+MasterCodePrintstheprogrammedRELAYSTRIKETIME.
*27+MasterCodePrintsthestatusofTIMEDANTI‐PASSBACK(OnorOff).
*55+MasterCodePrintsthesizeoftheMEMORYCHIPinstalledinthe1520(125,500or1000).
*37+MasterCodePrintstheTRANSACTIONScurrentlystoredinthe1520memorybuffer.
*31+MasterCodePrintsthestatusofREALTIMEprintmode(OnorOff).

SelectiveTransactionReport
Thefollowingprogrammingsequencewillprinttransactionsforaselectedmonth/day.

1.Press*34andenterthemastercode.[*34____(beep)]
2.Enterthemonth(January=01;December=12)thenpress*.[__*(beep)]
3.Enterthedayofthemonth(01–31)thenpress*.[__*(beep)]
4.Thetransactionfortheselectedmonthanddayshouldappearonyourcomputerscreen.
1520PrinttoPC Rev6‐11