DMC HI-CAP 40 User manual

OWNER’S MANUAL
HI-CAP 40
GRAIN
CLEANER
PNEG-1146
Date: 9-21-06
PNEG-1146

i
Safety and DecalsHi-Cap 40 Grain Cleaner
SAFETY INFORMATION PLEASE READ
WATCH FOR THIS SYMBOL!
IT POINTS OUT IMPORTANT SAFETY PRECAUTIONS.
IT MEANS ATTENTION -- “BECOME ALERT! YOUR SAFETY IS INVOLVED!”
It is recommended that you review the entire contents of this manual, paying
particular attention to items preceded by this symbol.
FAILURE TO HEED THESE INSTRUCTIONS
CAN RESULT IN PERSONAL INJURY!
Operator Qualifications
Operationofthisfarmsteadequipmentshallbelimitedtocompetentandexperienced
persons. In addition, anyone who will operate or work around power equipment must
use good common sense. In order to be qualified, he must also know and meet all
other requirements, such as:
1. Some regulations specify that no one under the age of 16 may operate power
machinery. This includes farmstead equipment. It is your responsibility to know
what these regulations are in your own area or situation.
2. Current OSHA regulations state in part: “At the time of initial assignment and at
least annually thereafter, the employer shall instruct every employee in the safe
operation and servicing of all equipment with which the employee is, or will be
involved.”*
3. Unqualified persons are to stay out of the work area. The “WorkArea” is defined
as any area within the grain drying and storage complex where this equipment
is installed.
4. A person who has not read and understood all operating and safety instructions
is not qualified to operate the machine.
*Federal Occupational Safety & Health Standards for Agriculture Subpart D,
Section 1928.57 (a) (6).

ii
Safety and Decals Hi-Cap 40 Grain Cleaner
BE A SAFE OPERATOR
1. Read and understand the Owner’s Manual.
2. Disconnect all electrical power before servicing or opening control box,
adjusting or lubricating the equipment.
3. All electrical hook-ups should be in accordance to the National Electrical
Code.
4. Ground all electrical equipment as well as bin itself.
5. Only knowledgeable and trained personnel should operate this equipment.
6. NEVER WORK WITH BELTS OR AUGERS WITH POWER “ON”...
automatic controls may start without warning! Stay clear of motors, belts and
augers.
FAILURE TO FOLLOW THESE INSTRUCTIONS MAY
RESULT IN PERSONAL INJURY OR PROPERTY DAMAGE.

iii
Safety and DecalsHi-Cap 40 Grain Cleaner
The Decals Show on This Page
MUST Be Displayed As Shown
Replacements are available upon request.
Write to: DMC
1004 E. Illinois St.
Assumption, IL 62510
Phone: [phone]
NOTE
The decals on this page are NOT actual size.
Keep all decals wiped clean at all times.
All decals must be replaced if they are destroyed, missing, painted
over, or can no longer be read.

iv
Hi-Cap 40 Grain Cleaner
INTRODUCTION
Your Hi-Cap Grain Cleaner is a high quality machine built to give years of reliable service.
With the wide range of screen sizes available, it will take care of all your screening needs.
With its dual screening action it not only removes the “fines”, chaff, etc., but also large trash
such as cob particles, stalks and straw. Power requirements are low, and the motors can be
connected to operate on either 115 or 230 Volts. The feed-in auger will operate in full half-
circle for easy unloading of grain.
SERVICE
Lubricateallgreasefittingsevery5,000bushels, or at least once everyyear. At the same time,
check belt tensions and clean any accumulated trash out of the pulley grooves.
OPERATION
CAUTION
For Your Protection
KEEP ALL SAFETY SHIELDS IN PLACE
As with all moving machinery, DO NOT stand close to the Hi-Cap Grain Cleaner while it is
operating, and always stop it to make adjustments.
The cleaning drum should turn 27 revolutions per minute, and rotate clockwise when viewed
fromthefeed-inend. Thecleaner should be rununtilemptybeforestopping. Itisnot advisable
to leave grain in the cleaner or start the cleaner with a load of grain in it.
The ADJUSTABLE BAFFLE in the internal screen serves two purposes: first, to force the
grain through the coarse screen close to the feed-in end to insure as much fine screening as
possible, and secondly, to prevent grain from working to the far end and out through the large
particle chute. It will be found that the baffle can be closer to the feed-in auger for dry grain
thanforwet. Observationofoperationwillrevealthe need for adjustment to give mostefficient
cleaning. If the grain tends to build up in the internal screen, set the baffle plate farther toward
the large particle chute end. Otherwise, keep it as close to the feed-in end as possible.
OPTIONAL EQUIPMENT
8” x 8’ Auger
4” x 15’TrashAuger
Steel Hopper for 4” TrashAuger
TrashPan
230 Volt, single-phase electrical power
All units shipped into Canada are wired 230 Volts only.

1
AssemblyHi-Cap 40 Grain Cleaner
Assembly Instructions
Step1 The component parts necessary for the make-up of the completed scanner are
shown in Photo 1.
Step 2 Use eight 3/8” x 1” hex head bolts, bolt the side rails to the front and rear frame
ends. Secure with 3/8” lock washers and nuts, as shown in Photos 2, 3 and 4.
Before tightening bolts, square the side rails with front frame end.
NOTE If trash pan is to be installed, attach the two side panel frame brackets when
attaching side rails. See Photo 5 and 6.
Step 3 Put wheels to the axles as shown in Photo 7. Secure with ¾” SAE washers and 3/
16” x 1” cotter keys. Place wheel on axle with the grease zerk on the outer side.
Step 4 Mount switch box to front frame end. To attach, open switch box cover and bolt to
switch mounting plate, using three ¼” x ¾” pan head bolts, lock washers and nuts.
See Photo 8.
Step 5 Using two 3/8” x 1-1/2” bolts; bolt dual bearing on the front frame-bearing mount.
See Photos 9 and 10. Fasten each bolt with 5/16” flat washer, 3/8” lock washer
and nut. BE SURE the dual bearing is positioned as shown in Photo 10 with
indentation up.
Step 6 Put the 3/8” pivot bolts into the drum belt tightener as shown in Photo 11. Next, put
the pivot bolts through the lower half of the double bearing and the bearing plate;
fasten with 5/16” flat washer, 3/8” lock washer and nut. Slide dual bearing to the
top of the slotted holes and TIGHTEN TEMPORARILY. See Photos 11, 12 and 13.
Step 7 Put the tension spring bracket on the 3/8” x 5-1/2” bolt, with the 3/8” nut, and turn
into bearing plate as shown in Photo 14.
Step 8 Place the 7/8” x 7-3/8” shaft, (keyway both ends) into double bearing with an equal
amount of shaft protruding from each end of dual bearing. See Photo 15. Next,
put a locking collar on each end of shaft and lock. Tighten setscrews. Last, place
½” moon keys into shaft. See Photos 16 and 17. Lock locking collar in direction of
rotation.
Step 9 Place the 7/8” x 2-1/2” two-groove “A” section pulley on the 7/8” shaft as shown in
Photo 18. Position pulley so that it is flush with the outside end of the shaft.
Tighten setscrews firmly.
Step 10 Slide the 14” pulley onto the 7/8” shaft, hub first. Position it tightly against bearing
locking collar. Tighten setscrews firmly. See Photo 19.

2
Assembly Hi-Cap 40 Grain Cleaner
Step 11 Bolt the electric motor on motor mount on front frame, using four 5/16” x 1” bolts,
eight ¼” flat washers and four 5/16” lock washers and nuts. Slide motor to upper-
most position in the slotted holes. See Photos 20 and 21.
Step 12 Place straight key into motor shaft slot. Next, place 5/8” x 2-1/4” pulley on the motor
shaft. Align with 14” pulley and tighten setscrews. See Photo 22. At this time, put
a 3/8” Romex connector into the motor junction box. Take loose wire from outlet
box and wire motor as described on wiring diagram on inside cover plate of elec-
tric motor. For 115 Volts, follow low voltage diagram; for 230 Volt, follow high
voltage diagram. Put motor belt (A-55) on the motor pulley and 14” pulley. Adjust
belt tension.
Step 13 Bolt drum bearing mount extension bracket and discharge shield bracket onto the
rear frame end, using two 3/8” x 1-1/4” bolts, lock washers and nuts. BE SURE
frame end is bolted between bearing mount and shield bracket.
FOR OLD STYLE THREE-PIECE TRASH PAN, SEE SUPPLEMENT PAGE.
FOR CLEANERS WITHOUT TRASH PAN,
ELIMINATE STEPS 14-19, GO DIRECTLY TO STEP 20.
Step 14 Bolt one-half of the collector pan to the rear end panel, using three ¼” x ½” pan
head machine screws, and hex flange lock nuts. See Photo 25. Continue by
bolting the other half of the collector pan to the rear end panel, finish by bolting the
two collector pan halves together at the bottom, using twelve ¼” x ½” pan head
screws, and hex flange lock nuts. See Photo 26.
Step 15 Position four-inch collector pan discharge auger in collector pan with flighting void
directly over the collector pan hole. Bolt front collector pan panel into place with
six ¼” x ½” pan head screws and hex flange lock nuts. See Photo 27.
Step 16 Install front end rear collector pan wooden bearings with six 5/16” x ¾” carriage
bolts, lock washers and hex nuts. See Photo 28.
Step 17 Pull key-wayed end of collector pan auger forward. Place 1” machine bushing to
the auger shaft and hold in position by driving a 3/16” x 1-1/2” spring pin through the
shaft. Install the 3/16” x 1” woodruff key onto the auger shaft and then position the
8” V-pulley with the hub out approximately 3/16” from the end of the shaft. See
Photos 29 and 30.
Step 18 Bolt the flanged idler pulley to the outside of the front panel using ½” x 3” hex bolt,
½” x ¾” spacer bushing, ½” flat washers. See Photo 31.
Assembly Instructions (continued)

3
AssemblyHi-Cap 40 Grain Cleaner
Assembly Instructions (continued)
Step 19 Place the pan on the cleaner frame and attach to the side rails, using eight ¼” x ¾”
hex bolts, flat washers and hex flange lock nuts. See Photos 32 and 33.
Step 20 Bolt the front bearing mount extension bracket and wood bearing together using
two 3/8” x 1” hex bolts, 5/16” flat washers, lock washers and nuts. Next slide the
wood bearing and bracket onto the drum shaft then place a 7/8” x 14 gauge ma-
chinery bushing to he shaft and secure with 3/16” x 1-1/4” steel pin. Continue by
lacing the wood bearing to the rear drum shaft, secure with a 7/8” shaft collar.
Step 21 Place drum drive belts over the drum shaft inside cone screen as shown in Photo
34.
Step 22 Lay assembled cleaner frame on side, with motor up. Roll drum into the as-
sembled frame with belt drive ring on the same end as the electric motor. Using
two 3/8” x 1-1/4” bolts, lock washers and nuts, bolt the front bearing extension
bracket to the cleaner main frame as shown in Photos 35 and 36.
Step 23 Using two 3/8” x 1” hex bolts, 5/16” flat washers, lock washers and nuts, bolt the
rear wood drum bearing to the bearing extension plate. Finish by pulling the
screener drum toward the rear until the front bearing spring pin (feed in end) is
against front bearing. Complete by locking shaft collar against rear wood bearing.
See Photo 37, or wood bearing revisions on Page ????.
BE SURE DRUM DRIVE BELTS ARE POSITIONED AS OUTLINED IN STEP 20.
SET GRAIN CLEANER UP ON ITS WHEELS. BE SURE ALL BOLTS ARE TIGHT.
Step 24 InstallA-90 belts over wooden idler, around 2-1/2” double groove pulley and onto
belt drive ring of drum. Finish by hooking belt tightener spring in position. See
Photo 38.
NOTE If trash pan equipped, install theA-112 belt to the 8” trash pan pulley, then to the
outer edge of drum drive ring. Adjust belt tension with flanged idler pulley. Attach
trash pan belt shield bracket using two ¼” x ¾” hex head bolts, lock washers and
nuts. Finish by bolting belt shield to bracket, using two ¼” x ¾” carriage bolts, flat
washers, lock washers and nuts. See Photos 39, 40 and 41.
Step 25 Bolt the discharge shield to the discharge shield bracket, using four ¼” x ¾” round
head machine screws, lock washers and nuts. See Photo 42.
Step 26 Bolt intake pan between small brackets on top of front frame, using two 3/8” x 1”
bolts, lock washers and nuts. See Photos 43 and 44.

4
Assembly Hi-Cap 40 Grain Cleaner
Step 27 Install the belt shield by putting a ½” nut on each shield mounting bolt, then place
a ½” flat washer to each bolt and continue by putting the shield into position. Se-
cure with another ½” flat washer, followed by a ½” nut. Adjust the shield so that it
will properly protect both pulleys. See Photo 43.
Step 28 The cone screens are usually installed at the factory. Should replacement or
change be necessary, remove the straps and self-tapping screws. Avariety of
cone screens are available for the individual needs. See Page ???.
Outside screens are installed by wrapping the screen around the outside of the
drum. BE SURE outside screen is lapped as shown in Photo 46. If incorrectly
installed, grain will get behind the screens, causing them to work their way off the
drum. Place head of machine screws in direction of drum rotation.
For easy placement of outside drum screens, two door springs can be attached to
either a small piece of steel or wood with hooks to hook into the screen. Then, by
using a stick or broom handle, tap the screen lightly. The door springs will take all
the excess slack out of the outside screen so the drum straps can be easily put on
and secured. Straps should be secured with ¼” and 2-1/2” machine screws and
nuts. See Photos 47 and 48.
NOTE Screen lap and outside drum straps should NOT be spliced on the same tumbling
bar.
Outside drum straps that are placed directly over drum rings should be tightened
securely. Common sense should be used when tightening straps that only come
in contact with the outside drum tumbling bars. Deforming of the bars could result
if these straps are over-tightened. BE SURE straps are positioned as shown in
Photos 47 and 48. REMEMBER, screen lap and outside drum straps should NOT
be on the same tumbling bar.
Step 29 By loosening the setscrews and turning the turnbuckle, you can adjust the slant of
your drum for proper operation. See Photo 49. The grain will pass through the
screener faster with a steep slant. The cleaning action will be more thorough with
less slant. IF TRASH PAN EQUIPPED:
Step 30 The drum side panel will mount with the channel edge on the top and to the out-
side. Bolt the end shield to the front end of the side panel using two ¼” x ½” pan
head machine screws, hex flange lock nuts.
Step 31 Bolt the two posts to the drum side panel using ¼” x ¾” hex bolts, lock washers
and hex nuts.
Assembly Instructions (continued)

5
AssemblyHi-Cap 40 Grain Cleaner
NOTE Before the bolts are tightened, the posts must be inserted into the slots of the
brackets on the frame for proper alignment. After the posts are aligned, tighten the
bolts. To secure side panel, push down and insert hairpin through hole in the post.
See Photos 50, 51 and 52.
Photo 52 shows a Model 40 Hi-Cap Grain Cleaner with optional trash pan attach-
ment, less auger.
Photo 53 shows a Model 40 Hi-Cap Grain Cleaner with optional trash pan, and 4’
x 15’TrashAuger.
MODEL 40 8” x 8’ FEED-IN AUGER
Assembly Instructions
Component Parts for 8’Feed-InAuger
Step 1 Place sealed bearing between bearing flanges, and bolt to auger head. BE
SURE eccentric lock is on the outside. Use two 5/16” x ¾” carriage bolts, lock
washers and nuts. See Photos 1 and 2.
Step 2 Slide stub shaft into upper end of auger flighting. BE SURE keyway is left ex-
posed. Fasten with two 3/8” x 1-3/4” Grade 5 bolts, and 3/8” lock nuts. See Photos
3 and 4.
Step 3 Place auger head over auger tube, sliding stub shaft through bearing. See Photo
5.
Step 4 Install 1” locking collar onto bearing. BE SRUE to lock the collar with the rotation
of the shaft. Auger shaft should stick through the locking collar 1-5/8”. Securely
tighten locking collar set screw. See Photos 6,7 and 8.
Step 5 Using one 2” strap bracket, four 3/8” x 1-1/4” bolts and nuts, fasten auger head
securely to auger tube. See Photos 9 and 10.
Step 6 Place a ½” nut on the threaded stub bolt on the auger head. Slide motor mount
angle over stub bolt and thread another ½” nut over the angle. Install motor mount
base plate to the auger head, using two 3/8” x ¾” carriage bolts, lock washers and
nuts. Do NOT tighten at this time. See Photos 11 and 12.
Step 7 Put two 5/16” x ¾” carriage bolts, lock washes and nuts through motor mount
angel, and motor mount base plate.
Assembly Instructions (continued)

6
Assembly Hi-Cap 40 Grain Cleaner
For 2 HP motor, bolt as in Photo 13.
For 1-1/2HP motor, bolt as in Photo 14.
Step 8 Using 5/16” carriage bolt, lock washer and nut, bolt the rear of the motor mount
base plate to the rear support on the auger head. See Photo 15.
Step 9 Bolt the auger pivot pin to under side of the auger head, using ½” x 3-1/2” bolt and
lock nut. Auger pivot must have free movement. See Photo 16.
Step 10 Install ¼” key into auger shaft. Then put 12” pulley onto shaft, hub first. Make shaft
flush with the outer edge of the pulley. Tighten setscrews. See Photos 17, 18 and
19.
Step 11 Bolt the motor to the motor mount base plate, using four 5/16” x 1” bolts, two flat
washers, one look washer per bolt and nuts. See Photo 20.
Step 12 Put key and 3” pulley to the motor shaft; align motor pulley with 12” auger pulley and
install belt. Adjust belt tension by raising the ½” nuts on the threaded stub bolts.
After belt adjustment has been made, tighten all bolts left loose during motor mount
assembly. See Photos 21 and 22.
Auger motor must be wired the same voltage as cleaner and checked for proper
rotation.
Step 13 Using two 5/16” carriage bolts, lock washers and nuts, bolt the belt shield to the
tabs on the auger head. See Photo 23.
Step 14 Put wooden bearing between bearing flanges and bolt to tail cage hopper with
three 3/8” x ¾” carriage bolts, flat washes, lock washers and nuts. See Photos 24
and 25.
Step 15 Install hopper wheel bracket, using two 3/8” x ¾” carriage bolts, flat washers, lock
washers and nuts. Slide two 5/8” SAE washers onto the shaft, then the wheel, and
another 5/8” SAE washer. Finish by installing a 1-1/4” cotter pin. See Photos 26 and
27.
Step 16 Slide flow restrictor tube into intake end of auger tube with nut welded onto
restrictor tube on the outer end. See Photo 28.
Step 17 Put the tail cage hopper assembly onto the auger tube. Insert the end of auger
shaft into the wooden bearing. Secure the tail cage hopper assembly to the auger
tube by using two 2” strap brackets. (Be sure to put the 2” strap bracket with pipe
and threaded nut toward the top of the tail cage assembly as shown in Photo 29
and 30.) Securely fasten with four 3/8” x 1-1/4” hex head bolts as shown in Photo 31.
Assembly Instructions (continued)

7
AssemblyHi-Cap 40 Grain Cleaner
Assembly Instructions (continued)
Step 18 Put the flat end of the guide rods into the bushings provided at the back of the
hopper. Align the holes in the rod with those in the bushing and secure with 1/8” x
1-1/4” cotter pins as shown in Photos 32 and 33.
Step 19 Place the slide flow restrictor adjustment handle through the bushing welded to
the 2” strap brackets and bolt to the flow restrictor tube with one 5/16” x ¾” hex
head bolt and lock washer. Finish by turning the wing bolt into the nut welded on
bushing of the strap bracket. See Photos 34, 35 and 36.
Step 20 Install the hopper latch and upper glide rod support bracket by placing the ends of
the glide rod support bracket through the holes in the hopper and to the pointed
guide rod ends. Fasten the latch to the hopper with the two 3/8” flat washers, and
two cotter pins. See Photos 37 and 38.
Step 21 Assemble the hopper extensions using six ¼” x ½” pan head machine screws and
¼” hex head flanged whiz lock nuts. Once the upper extensions are assembled,
fasten the glide rod guides to the upper extensions using ten ¼” x ½” pan head
machine screws. See Photos 39 and 40. BE SURE to install bolts as shown in
Photo ???.
Step 22 Slide hopper extension assembly onto glide rods. Lift up latch and finish assem-
bly by placing hairpin clips through holes of guide rods. See Photos 41 and 42.
OPERATE Auger and OBSERVE for proper rotation.
Change wires in motor for rotation correction.

8
Parts List Hi-Cap 40 Grain Cleaner
Bearing Revisions
Reference Part Quantity
Number Number Description Needed
1 103C0025 Extension Spring, Belt Tightener 1
2 202B0046 Belt Tightener, Drum Drive 1
3 202B0050 Bearing Mount Extension Bracket 2
4 202B0051 Pivot Bolt, Belt Tightener Bracket, 3/8" 2
5 202B0052 Spring Tension Bracket 1
6 202B0063 Double Bearing Weldment 1
7 202B0064 Double Bearing Assembly 1
8 204B0018 Flat Idler Pulley 1
9 PT0133 Wood Pillow Block Bearing, 7/8" Complete 2
10 PT0208 Bearing, Eccentric Lock, 7/8" 2
11 PT0228 Wood Bearing, 7/8" Bore 2
12 PT0400 Collar, 7/8" Set Screw Lock 1
13 PT0402 Collar, Eccentric Lock, 7/8" 2
14 PT0414 2 Holed Stamped Pillow Block 2
15 PT0611 Pulley, 2-1/2" x 7/8", Double Groove, A Section 1
16 1FH0765 Hex Nut, 3/8" 9
17 2FH0855 Hex Bolt, 3/8" x 1" 8
18 2FH1041 Hex Bolt, 3/8" x 5-1/2", Full Thread 1
19 3FH0561 Snap Ring, 5/8" 1
20 3FH0791 Lock Washer, 3/8" Medium 8
21 3FH0829 Machinery Bushing, 1-3/8" O.D. x 7/8" I.D. x 14 GA 1
22 3FH0864 Flat Washer, 5/16" 8
23 3FH0930 Spring Pin, 3/16" x 1-1/4" 1
24 3FH0952 Flat Washer, 5/8" SAE 3
Front Drum Bearing Rear Drum Bearing Double Bearing

9
Parts ListHi-Cap 40 Grain Cleaner
MODEL 40 HI-CAP GRAIN CLEANER PARTS

10
Parts List Hi-Cap 40 Grain Cleaner
Reference # Part # Description Qty Needed
1 10C30025 Extension Sprin
g
, Belt Ti
g
htene
r
1
2 202A0028 Inside Cone Screen Strap, 60-1/4" 1
3 202A0029 Inside Cone Screen Strap, 57-1/8" 1
4 202A0030 Inside Cone Screen Strap, 88-1/2" 1
5 202A0031 Outside Drum Screen Strap, 125-7/8" 7
6 202A0038 Screen, Inside Cone
(
Refer To Screen Selection Guide for Wire Size
)
2
7 202A0039 Screen, Trash Spout Section 1
8 202A0040 Screen, Outside Drum, Set of 1-24" Width and 1-36" Width 1
9 202A0042 Drum 1
10 202B0001 Frame End, Rea
r
1
11 202B0022
A
d
j
ustin
g
Le
g
, Front Frame 1
12 202B0025 Intake Pan 1
13 202B0034 Bracket, Dischar
g
e Shield 1
14 202B0035 Side Rail, Main Frame 2
15 202B0038 Belt Shield 1
16 202B0041 Dischar
g
e Shield 1
17 202B0044 Countershaft, 7/8" x 7-3/8" 1
18 202B0046 Belt Ti
g
htener, Drum Drive 1
19 202B0050 Bearin
g
Mount Extension Bracket 2
20 202B0051 Pivot Bolt, Belt Ti
g
htener Bracket, 3/8" 2
21 202B0052 Sprin
g
Tension Bracket 1
22 202B0057 Main Frame, Front 1
23 202E0003 Power Cord, Cleaner Moto
r
1
24 202E0008 Power Cord, To Au
g
er, 115 Volt 1
202E0005 Power Cord, To Au
g
er, 230 Volt 1
25 202E0009 Power Cord, Lead In, 115 Volt 1
205E0004 Power Cord, Lead In, 230 Volt 1
26 204B0018 Flat Idler Pulle
y
1
27 PT0108 Double Bearin
g
, Countershaft, 7/8" 1
28 PT0113 Drum Bearin
g
, Set Screw, 7/8" 2
29 PT0208 Bearin
g
, Eccentric Lock, 7/8" 2
30 PT0209 Bearin
g
, 7/8" 1
31 PT0402 Collar, Eccentric Lock, 7/8" 2
32 PT0417 Bearin
g
Housin
g
, Drum 1
33 PT0418 Bearin
g
Housin
g
, Double 1
34 PT0497 Belt, Motor Drive, A-55 1
35 PT0512 V-Belt, Drum Drive, 1-90
(
Matched Set
)
2
36 PT0605 Pulle
y
, Motor Drive, 5/8" x 2-1/4", A Section 1
37 PT0611 Pulle
y
, 2-1/2" x 7/8", Double Groove, A Section 1
38 PT0690 Pulle
y
, 7/8" x 14", A Section 1
39 MS0010 Wheel, 2-3/4" x 10" x 3/4" 2
40 1EL0401 Connector, 3/8", 115 Volt 3
1EL0401 Connector, 3/8", 230 Volt 4
1EL0403 Connector, 3/4", 115 Volt 1
41 1EL0667 Plu
g
, 125 Volt, 30 Amp 1
1EL0668 Plu
g
, 230 Volt, 20 Amp 1
42 1EL0673 Twist Connector, 125 Volt, 30 Amp 1
1EL0675 Twist Connector, 230 Volt, 20 Amp 1
43 2EL0320 Switch Box, 240 Volt, A.C., 30 Amp 1
44 3EL5064 Motor, 1/2 HP, TEFC, Electri
c
1
45 1FH0763 Hex Nut, 1/4" 17
46 1FH0764 Hex Nut, 5/16" 4
47 1FH0765 Hex Nut, 3/8" 23
48 1FH0767 Hex Nut, 1/2" 4
49 2FH0477 Self Tappin
g
Hex Screw, #10 x 3/4" 12
50 2FH0617 Square Head Set Screw, 3/8" x 3/4" 2
51 2FH0726 Round Head Machine Screw, 1/4" x 3/4" 7
52 2FH0735 Round Head Machine Screw, 1/4" x 2-1/2" 10
53 2FH0830 Hex Bolt, 5/16" x 1" 4
54 2FH0855 Hex Bolt, 3/8" x 1" 10
55 2FH0856 Hex Bolt, 3/8" x 1-1/4" 4
56 2FH0857 Hex Bolt, 3/8" x 1-1/2" 6
57 2FH1041 Hex Bolt, 3/8? X 5-1/2", Full Thread 1
58 3FH0561 Snap Rin
g
, 5/8" 1
59 3FH0730 Cotter Pin, 3/16" x 1-1/4" 2
60 3FH0789 Lock Washer, 1/4" 7
61 3FH0790 Lock Washer, 5/16" Medium 4
62 3FH0791 Lock Washer, 3/8" Medium 22
63 3FH0863 Flat Washer, 1/4" 8
64 3FH0864 Flat Washer, 5/16" 4
65 3FH0867 Flat Washer, 1/2" 4
66 3FH0930 Sprin
g
Pin, 3/16" x 1-1/4" 1
67 3FH0952 Flat Washer, 5/8" SAE 3
68 3FH0954 Flat Washer, 3/4" SAE 2
69 3FH0976 Cupped Washer, 7/8" O.D. x 17/64" 12
70 3FH0992 Woodruff Ke
y
, 3/16" x 1" 2
71 6FH001 Tornbuckle, 5/8" 1
MODEL 40 HI-CAP GRAIN CLEANER PARTS

11
Parts ListHi-Cap 40 Grain Cleaner
8” x 8’Auger

12
Parts List Hi-Cap 40 Grain Cleaner
Reference Part Quantit
y
Numbe
r
Numbe
r
Description Needed
1 202C0137 Auger Tube, 7" 1
2 202
C
0410 7
O
D Auger, 8' 1
3 202E0006 Power
C
ord
(S
peci
f
y 115 Volt or 230 Volt
)
1
4 204
C
0010
A
uger Pivot 1
5 205
C
0002 2"
S
trap Bracket 1
6 205
C
0003 Motor Mount Angle 1
7 205
C
0005 Motor Mount Base Plate 1
8 205
C
0008
A
uger Head 1
9 205
C
0012 Motor Belt
S
hield 1
10 205
C
0016 Tail
C
age Hopper 2
11 205
C
0022 Latch and
G
lide Rod
S
upport 1
12 205
C
0025
G
lide Rod 2
13 205
C
0027 Hopper Wheel Bracket 1
14 205
C
0030
G
lide Rod
G
uide 1
15 205
C
0031 Right
S
liding Hopper
S
heet 1
16 205
C
0032 Le
f
t
S
liding Hopper
S
heet 1
17 205
C
0038
S
liding Hopper End
S
heet 1
18 205
C
0039
S
tub
S
ha
f
t1
19
205C0040
Fl
ow
R
es
t
r
i
c
t
or
St
rap
B
rac
k
e
t
1
20 205
C
0043 Flow Restirctor Adjustment Handle 1
21
205C0044
Fl
ow
R
es
t
r
i
c
t
or
T
u
b
e
1
22 2FH0428
A
dj.
S
crew, 5
/
16 x 7
/
81
23
205C0056
Ri
g
ht
E
n
d
Glid
e
R
o
d
G
u
id
e
1
24 205
C
0057 Le
f
t End
G
lide Rod
G
uide 1
25
205C0060
Fl
ow
R
es
t
r
i
c
t
or
St
rap
B
rac
k
e
t
,
With
ou
t
N
u
t
1
26 PT0203 Bearing,
S
ealed With Eccentric Lock, 1" 1
27
PT0219
W
oo
d
B
ear
i
ng,
1
-
1/4"
B
ore
0
28 PT0401
C
ollar, Eccentric Lock, 1" 2
29
PT0420
2
H
o
l
e
B
ear
i
ng
M
oun
ti
ng
Fl
ange
1
30 PT0424 3 Hole
C
enter Flange Mount 1
31
PT0490
B
-
48
V
-
B
e
lt
1
32 PT0681 Pulley, 1" x 12", B
S
ection 1
33
PT0706
M
o
t
or
D
r
i
ve
P
u
ll
ey,
5/8"
x
3"
,
B
S
ec
ti
on
1
34 M
S
0021 6" Rubber Wheel 1
35 1EL0401
C
onnector, 3
/
8" 1
36 1EL0667 Plug, 125 Volt, 30 Amp. 1
1EL0668 Plug, 230 Volt, 20 Amp. 1
37 3EL5097 Motor, 1-1
/
2 HP, TEF
C
, Electric 1
38 1FH0736 Lock Nut, 3
/
8" 2
39 1FH0738 Lock Nut, 1
/
2" 1
40 1FH0764 Hex Nut, 5
/
16" 11
41 1FH0765 Hex Nut, 3
/
8" 11
42 1FH0767 Hex Nut, 1
/
2" 2
43 1FH0995 Hex Flange Whiz Lock Nut, 1
/
4" 16
44 2FH0512
S
ocket Head
S
et
S
crew, 5
/
16" x 5
/
16" 3
45 2FH0645
C
arriage Bolt, 5
/
16" x 3
/
4" 7
46 2FH0659
C
arriage Bolt, 3
/
8" x 3
/
4" 7
47 2FH0747 Pan Head Machine
S
crew, 1
/
4" x 1
/
2" 16
48 2FH0828 Hex Bolt, 5
/
16" x 3
/
4" 1
49 2FH0830 Hex Bolt, 5
/
16" x 1" 4
50 2FH0856 Hex Bolt, 3
/
8" x 1-1
/
4" 8
51
2FH0913
H
ex
B
o
lt
,
1/2"
x
3
-
1/2"
1
52 2FH1057 Hex Bolt, 3
/
8" x 1-3
/
4",
G
rade 5 2
53
3FH0712
C
o
tt
er
Pi
n,
1/8"
x
3/4"
2
54 3FH0714
C
otter Pin, 1
/
8" x 1-1
/
4" 3
55
3FH0730
C
o
tt
er
Pi
n,
3/16"
x
1
-
1/4"
1
56 3FH0770
C
otter Hair Pin, 1
/
8" x 2-3
/
8" 2
57
3FH0790
L
oc
k
W
as
h
er,
5/16"
12
58 3FH0791 Lock Washer, 3
/
8" 7
59
3FH0864
Fl
a
t
W
as
h
er,
5/16"
9
60 3FH0865 Flat Washer, 3
/
8" 4
61
3FH0952
Fl
a
t
W
as
h
er,
5/8"
SAE
3
62 3FH1015
S
quare Key, 3
/
16" x 1" 1
63
3FH1026
S
quare
K
ey,
1/4"
x
1"
1
8” x 8’Auger Parts List

13
Parts ListHi-Cap 40 Grain Cleaner
4” x 15’ Fines Auger

14
Parts List Hi-Cap 40 Grain Cleaner