DMP Electronics CellComRT User manual

InstallatIon GuIde
CellComRT Digital Cellular Communicator
Description
The CellComRT Digital Cellular Communicator provides a fully supervised alarm communication path over the GSM/
GPRS network. The CellComRT is installed remote from the panel enclosure in a supplied plastic housing and can be
powered directly from the XR100 or XR500 Series panel LX header or can be powered from an optional power supply.
What is Included
The CellComRT includes the following:
• One Remote Cellular Communicator
• One380-400SecureComWirelessSIMCard
• PlasticHousing
• One383RubberDuckAntenna
• OneCELLCOMBATLithiumPolymerRechargeableBattery
Compatibility
The CellComRT is compatible with the XR100, XR100N, XR500,
XR500NandXR500ECommandProcessorsusingsoftwareVersion
203orhigher.TheCellComRToperatesonthepanelLXheader
andcanbeusedwithan1100SeriesWirelessReceiver.
Installation Safety
Ground Yourself Before Handling the Panel! To discharge
static, touch any grounded metal, such as the enclosure,
before touching the panel.
Remove All Power From the Panel! RemoveallACandBatterypowerfromthepanelbeforeinstallingorconnecting
any modules, cards, or wires to the panel.
Bus Connection
TheCellComRTinterfaceswiththeXR100/XR500Seriesusingthepanel’son-boardLX-Busheader(J22). The
CellComRTcanbemountedupto100feetfromthepanelenclosureusing22AWGwireor250feetusing18AWG
wire.
Harness Connection
Use the following steps to connect the CellComRT to the panel:
1.Installajumperacrosstheheaderpinsnexttotheletter“X”ontheXR100/XR500panel’sJ23header.
2. Connectthe4-wireharnessfromtheJ22headerontheCellComRTtotheXR100/XR500panel’sLX-Busheader(J22).
3.Afterpower-upoftheCellComRT,brieyresettheXR100/XR500panelusingtheJ16jumpertoactivate
operation.
Installing the CellComRT
Connecting Backup Rechargeable Battery
Observepolarityandconnecttherechargeablebatteryleadconnectortothe2-pinCellComJ4
battery header.
Tamper Switches
The CellComRT is equipped with two tamper switches. One is located inside the housing. The
second tamper is a wall tamper switch. BeforemountingtheCellComRTunit,followthesesteps
to install the tamper springs:
1. Place the included tamper springs on the tamper switches. The long tamper spring installs
inside the housing and the short tamper spring installs in the opening in the back of the
CellComRT housing.
2.Withspringinplace,mounttheCellComRTonaatsurfacethatengagesthetamper
spring and closes the tamper. See Figure 1 for mounting hole locations.
Connecting the Antenna to the CellComRT
AttachtheRubberDuckAntennatotheAntennaSMAConnector(J19)locatedonthetopright
side of the CellComRT. See Figure 2.
CellComRT
Mounting Holes
Antenna
Tamper
Switch
S2
J19
Battery
Transmit LED
J4
SIM Card
Holder
J22
Mounting Screw
Shoulder Washer
Figure 1: CellComRT PCB
Antenna
Ta mper
Switch
S2
J19
Battery
Charge LED
Transmit LED
J16 Reset
J22
CellCom
J4 J25
SIM Card
Holder
J5
Rubber Duck
Antenna
Figure 2: CellComRT
Antenna Installation

Digital Monitoring Products CellCom Installation Guide
2
Connecting the Optional Auxiliary Power Supply
Use the following steps when connecting an optional
auxiliarypowersupplytotheCellComRT:
1.ConnecttheRedwire(auxiliaryPower)to
thetopCellComRTJ22terminalposition‘R’
andtotheDCpositiveterminal(+)ofthe
powersupply.SeeFigure3.
2.ConnecttheBlackwire(ground)tothe
bottomCellComRTJ22terminalpositionand
totheDCnegativeterminal(-)ofthepower
supply andtotheLXheader(J22)onthe
XR100/XR500Seriespanel.SeeFigure3.
Connecting the Optional Plug-in Transformer
WhenusinganoptionalModel376plug-inDCpowersupply,
mount the CellComRT near a wall outlet. Use the following steps
toconnecttheplug-inpowersupplytotheCellComRT:
1.Removethebarrelconnectorfromthe376powersupply.
2.Connecttheplug-inpowersupplyBlackwirewithWhite
stripestothetopCellComRTJ22terminalposition‘R’.
SeeFigure4.
3.Connecttheplug-inpowersupplysolidBlackwireto
thebottomCellComRTJ22terminalpositionand to the
LXheader(J22)ontheXR100/XR500Seriespanel.See
Figure4.
4.Plugthepowersupplyintoa110VoltACoutletnot
controlled by a switch.
Programming/Activation
Cellular Service is required before using the CellComRT for signal transmission. Using Remote Link panel
communicationprogramming,selectCELLasoneoftheCommunicationpaths.TheCellComRTcomeswithaSIM
cardreadyforactivationwithSecureComWireless,LLC.Moreinformationisavailableatwww.securecomwireless.
comorrefertotheRemoteLinkGuide(LT-0565).Or,useaSIMcardprovidedbytheGPRScarrierofyourchoice.
LED Indicator
The CellComGreenTransmitLEDlightasheswhentransmissionisbeingmadebetweentheCellComRTandthe
panel.
Diagnostics
The XR100/XR500 Series panels provide a Diagnostics function to test Communication integrity and the Cellular
SignalstrengthoftheCellComRT.TouseDiagnostics,resetthepanel,entertheDiagnosticscode2313(DIAG),and
pressCOMMAND.
Communication Status
SelectCOMMSTATUSfromtheDiagnosticsmenu.TheXR100/XR500panelstesttheCellComRTforthefollowing
items:
•CellComOperating •CellularTowerDetected •APN(AccessPointName)Correct
•SIMCardInstalled •SIMCardRegistered/Active •CommunicationPathIntegrity
Cellular Signal
SelectCELLSIGNALfromtheDiagnosticsmenu.TheXR100andXR500Seriespanelstestandindicatethestrength
ofthesignalusingabardisplay.Onebarindicatingaweaksignal.Sevenbarsindicatingastrongsignal.Ifthebars
indicatesaweaksignal,optionstocorrectthisproblemincluderelocatingtheCellComRTassemblyorextendingthe
CellComRTantennacoaxusingaModel381CoaxExtension.
Red—Auxiliary Power
Yellow—Data In
Green—Data Out
To LX Header (J22) on
XR100/XR500 panel
Black—Ground
Battery
Transmit LED
J22
J4
CellComRT
376
DC Plug-in
Power
Supply
Black Wire with
White Stripes
Solid
Black
Wire
Figure 4: Optional Plug-in Transformer Installation
502-12 Power Supply
J2 J3 J5
AC + BAT –+ DC –
Green
LED
AC
Red
LED
DC
Red—Auxiliary Power
Yellow—Data In
Green—Data Out
To LX Header (J22) on
XR100/XR500 panel Black—Ground
Battery
Transmit LED
J22
J4
CellComRT
Figure 3: Optional Auxiliary Power Supply Installation

CellCom Installation Guide Digital Monitoring Products
3
Rechargeable Battery
TheCellComRTrechargeablebatteryisusedtoprovide24hoursofbackupbatterypowerwhenDCpowerisnot
available.ThebatteryisintendedforbackuppoweronlyandnottooperatetheCellComRTonadailybasis.Ifthe
batteryislow,ornotpluggedintotheJ4batteryconnector,alowbatteryconditionisindicatedbytheCellComRT
Cellular Communicator.
Note:IfremovingtheCellComRTfromservice,disconnectthebackupbatteryfromtheCellComRTJ4connector.
Installing or Replacing the Battery Assembly
Observepolaritywhenpluggingthebatteryconnectorintotheheader.UseonlyDMPModelCELLCOMBAT.
Removing the Battery Assembly
1.DisconnectthebatteryleadconnectorfromtheCellComRTJ4batteryheader.
2.RemovethebatteryPCBfromthethreestandoffsbyunsnappingthetopoftheplasticclips.
3.Properlydisposeoftheusedbattery.
Caution:Riskofre,explosion,andburns.Donotdisassemble,heatabove212°F(100°C),orincinerate.
Properly dispose of used batteries.
Installing the Battery Assembly
1.AlignthethreebatteryPCBstandoffmountingholeswiththestandoffs.SeeFigure5.
2. Snap the battery assembly in place.
3.ObservepolarityandconnectthebatteryleadconnectortotheCellComJ4batteryheader.
Battery Assembly
Standoff
Antenna
Tamper
Switch
S2
J19
Battery
Transmit LED
J4
SIM Card
Holder
CellComRT
J22
Figure 5: Battery Assembly Standoffs
Antenna
Tamper
Switch
S2
J19
Battery
Transmit LED
J4 J25
SIM Card
Holder
CellComRT
J22
Figure 6: CellComRT Assembly

Digital Monitoring Products CellCom Installation Guide
4
CellCom System Messages
ThefollowingmessagesarecommunicatedtotheDMPSCS-1RreceivertoindicateCellComstatus:
130WARNING:CellCommunicatorBusFailed
COMMUNICATIONSECURITYFEATURE
The communication on the bus between the panel and the cellular communicator has failed while no areas of
the system were armed. This message may originate from both the panel and the cellular communicator as both
monitorthebus.TherestoralmessageisS132.
131ALARM:CellCommunicatorBusFailed
SERVICENOTIFICATIONFEATURE
The communication on the bus between the panel and the cellular communicator has failed while any area of the
system was armed. This message may originate from both the panel and the cellular communicator as both monitor
thebus.TherestoralmessageisS132.
132CellCommunicatorBusRestored
SERVICENOTIFICATIONFEATURE
The communication on the bus between the panel and the cellular communicator has restored. Message is sent
fromthepaneltothereceiverandisarestoralforS130andS131.
133WARNING:CellCommunicatorDCFailed
SERVICENOTIFICATIONFEATURE
The panel has received a message from the cellular communicator that its input DC voltage is missing or low. The
cellularcommunicatorisoperatingfromitsinternalbattery.TherestoralmessageisS134.
134CellCommunicatorDCRestored
SERVICENOTIFICATIONFEATURE
The panel has received a message from the cellular communicator that its input DC voltage has restored. This
messageisarestoralforS133.
135WARNING:CellCommunicatorLowBattery
SERVICENOTIFICATIONFEATURE
The panel has received a message from the cellular communicator that the cellular communicator’s standby
batteryislowormissing.TherestoralmessageisS136.
136CellCommunicatorBatteryRestored
SERVICENOTIFICATIONFEATURE
The panel has received a message from the cellular communicator that the cellular communicator’s standby
batteryhasrestored.ThismessagerestoresS135.
137WARNING:CellCommunicatorTamper
SECURITYFEATURE
Thepanelhasreceivedamessagefromthecellularcommunicatorthatthecellularcommunicator’sbuilt-in
tamper circuit was placed in an open condition while no areas of the system were armed. The restoral message is
S139.
138ALARM:CellCommunicatorTamper
SECURITYFEATURE
Thepanelhasreceivedamessagefromthecellularcommunicatorthatthecellularcommunicator’sbuilt-in
tamper circuit was placed in an open condition while one or more areas of the system were armed. The restoral
messageisS139.
139CellCommunicatorTamperRestored
SECURITYFEATURE
Thepanelhasreceivedamessagefromthecellularcommunicatorthatthecellularcommunicator’sbuilt-in
tampercircuitwasrestoredtoanormalcondition.ThismessageisarestoralforS137andS138.
AllthemessagesabovearecommunicatedbytheXR100/XR500controlpanelexceptS130andS131Cell
CommunicatorBusFailwhichissentbyboththepanelandCellCom.Forcompleteinformation,refertotheHost
CommunicationSpecication(LT-0086).

CellCom Installation Guide Digital Monitoring Products
5
FCC Information
ThisdevicecomplieswithPart15oftheFCCRules.Operationissubjecttothefollowingtwoconditions:
(1)Thisdevicemaynotcauseharmfulinterference,and
(2)thisdevicemustacceptanyinterferencereceived,includinginterferencethatmaycauseundesiredoperation.
Changesormodicationsmadebytheuserandnotexpresslyapprovedbythepartyresponsibleforcompliancecouldvoidthe
user’s authority to operate the equipment.
NOTE: ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigitaldevice,pursuanttopart15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordancewiththeinstructions,maycauseharmfulinterferencetoradiocommunications.However,thereisnoguarantee
thatinterferencewillnotoccurinaparticularinstallation.Ifthisequipmentdoescauseharmfulinterferencetoradioor
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
 -Reorientorrelocatethereceivingantenna.
 -Increasetheseparationbetweentheequipmentandreceiver.
 -Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiverisconnected.
 -Consultthedealeroranexperiencedradio/TVtechnicianforhelp.
Listed Compliance Specications
Commercial Burglary
Forlistedinstallations,theCellComRTmaybeinstalledinthefollowingcongurations:
•Installedanddirectlypoweredfromthecontrolpanel.
•InstalledandpoweredfromaUL603listedpowersupply.
TheadditionalonboardstandbyLithium-Ionbattery,CELLCOMBAT,isconsideredauxiliaryoperationandhasnot
been evaluated by UL.
TheoptionalModel376Plug-inDCPowerSupplyisconsideredauxiliaryoperationandhasnotbeenevaluatedbyUL.

800-641-4282
      
www.dmp.com 2500 North Partnership Boulevard

 
LT-0999 © 1.01 2009 Digital Monitoring Products, Inc.
9112
Compatibility
DMP Command Processor panels XR100, XR100N, XR500,
XR500N,XR500EusingSoftwareVersion203orhigher
Listings and Approvals
FCCPart15andCISPR22
FCCID:MIVGSM0308
IndustryCanadaID:4160A-GSM0308
UnderwritersLaboratories(UL)Listed
ANSI/UL365 PoliceStationConnectBurglarAlarmSystems
ANSI/UL985 HouseholdFireWarningSystemUnits
ANSI/UL1023 HouseholdBurglarAlarmSystemUnits
ANSI/UL1076 ProprietaryBurglarAlarmUnits&Systems
ANSI/UL1610 CentralStationBurglarAlarmUnits
Export Control
 TheCellComRTusesAESencryptionandanyexportbeyond
theUnitedStatesmustbeinaccordancewithExport
AdministrationRegulations.
Specications
PrimaryPower 12VDC
Current Draw
 Standby  21mA
 PeakTransmission200mA
Ordering Information
CellComRT Remote Digital Cellular
Communicator
Accessories
376  DCPlug-inPowerSupply
380-400 Level400SIMCard(1supplied)
381-12 12'CoaxExtension
381-25 25'CoaxExtension
383  RubberDuckAntenna
386  WallMountAntennaBracket
CELLCOMBAT ReplacementRechargeable 
  Batteryassembly