DMP Electronics CellCom-LTE-V SERIES Installation guide

CellCom-LTE-V SERIES
UNIVERSAL ALARM COMMUNICATOR
INSTALLATION AND PROGRAMMING GUIDE

Digital Monitoring Products CellCom- LTE-V Series Installation and Programming Guide
ii
FCC NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
If necessary, the installer should consult the dealer or an experienced radio/television technician for additional
suggestions. The installer may nd the following booklet, prepared by the Federal Communications Commission, helpful:
“How to identify and Resolve Radio-TV Interference Problems.”
This booklet is available from the U.S. Government Printing Oce, Washington D.C. 20402
Stock No. 004-000-00345-4
© 2018 Digital Monitoring Products, Inc.
Information furnished by DMP is believed to be accurate and reliable.
This information is subject to change without notice.
The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all
persons.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1)
THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Industry Canada
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2)
l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
Caution Notes
Throughout this guide, you will see caution notes containing information you need to know when installing the
c ommunicator. These cautions are indicated with a yield sign. Whenever you see a caution note, make sure you
completely read and understand its information. Failing to follow the caution note can cause damage to the
equipment or improper operation of one or more components in the system.

CellCom -LTE-V Installation and Programming Guide Digital Monitoring Products
iii
TABLE OF CONTENTS
Table of Contents
Description ....................................................................................................................... 1
What is Included ............................................................................................................... 1
System Components......................................................................................... 1
1.1 Terminals............................................................................................................... 2
1.2 Programming (PROG) Connection............................................................................ 2
1.3 Tamper.................................................................................................................. 2
1.4 Reset Button.......................................................................................................... 2
1.5 Load Button........................................................................................................... 2
1.6 Backlit Logo........................................................................................................... 3
Mount the CellCom-LTE-V Series Communicator ............................................. 4
2.1 Select a Location.................................................................................................... 4
2.2 Mount the Communicator ....................................................................................... 4
2.3 Connect the Antenna.............................................................................................. 4
Applications...................................................................................................... 5
3.1 CID Dialer Connection ............................................................................................ 5
3.2 Zones 1 - 4 Input Connection.................................................................................. 5
3.3 Zone 4 Bell Connection........................................................................................... 6
3.4 Ademco/Honeywell ECP Connection......................................................................... 8
3.5 Using Outputs for Communication Failure................................................................. 9
Remote Arming and Disarming ...................................................................... 10
4.1 Virtual Keypad App and VirtualKeypad.com .............................................................10
4.2 Using Outputs to Arm and Disarm ..........................................................................10
Programming the CellCom-LTE-V Series Universal Alarm Communicator ..... 11
5.1 Before You Begin ..................................................................................................11
5.2 Getting Started .....................................................................................................11
5.3 Programming Menu ...............................................................................................11
5.4 Reset Timeout ......................................................................................................12
5.5 Special Keys..........................................................................................................12
5.6 Entering Letters and Special Characters ..................................................................13
5.9 Keypad Displays Current Programming....................................................................13
Initialization................................................................................................... 14
6.1 Initialization..........................................................................................................14
6.2 Clear All Codes......................................................................................................14
6.3 Clear All Schedules................................................................................................14
6.4 Clear Events .........................................................................................................14
6.5 Clear Zone Programming .......................................................................................14
6.6 Clear Communication ............................................................................................14
6.7 Set to Factory Defaults ..........................................................................................14
Communication .............................................................................................. 15
7.1 Communication .....................................................................................................15
7.2 Account Number ...................................................................................................15
7.3 Transmission Delay................................................................................................15
7.4 Communication Type .............................................................................................15
7.5 Test Time .............................................................................................................15
7.6 Test Days .............................................................................................................15
7.7 Cell Check-In ........................................................................................................15
7.8 Fail Time ..............................................................................................................15
7.9 Receiver 1 Programming........................................................................................15
7.10 Alarm Reports.......................................................................................................15
7.11 Supervisory/Trouble Reports ..................................................................................15
7.12 Opening/Closing and User Reports .........................................................................15
7.13 Test Report...........................................................................................................16
7.14 First IP Address.....................................................................................................16
7.15 First IP Port ..........................................................................................................16

Digital Monitoring Products CellCom- LTE-V Installation and Programming Guide
iv
TABLE OF CONTENTS
7.16 Second IP Address ................................................................................................16
7.17 Second IP Port......................................................................................................16
7.18 Receiver 2 Programming........................................................................................16
7.19 Alarm Reports.......................................................................................................16
7.20 Supervisory/Trouble Reports ..................................................................................16
7.21 Opening/Closing and User Reports .........................................................................16
7.22 Test Report...........................................................................................................16
7.23 First IP Address.....................................................................................................16
7.24 First IP Port ..........................................................................................................17
7.25 Second IP Address ................................................................................................17
7.26 Second IP Port......................................................................................................17
Remote Options.............................................................................................. 18
8.1 Remote Options ....................................................................................................18
8.2 Remote Key ..........................................................................................................18
8.3 Remote Disarm .....................................................................................................18
8.4 App Key................................................................................................................18
System Reports .............................................................................................. 19
9.1 System Reports.....................................................................................................19
9.2 Opening/Closing Reports .......................................................................................19
9.3 Zone Restoral Reports ...........................................................................................19
System Options .............................................................................................. 20
10.1 System Options.....................................................................................................20
10.2 Entry Delay 1........................................................................................................20
10.3 Exit Delay .............................................................................................................20
10.4 Cross Zone Time ...................................................................................................20
10.5 Power Fail Delay....................................................................................................20
10.6 Swinger Bypass Trips.............................................................................................20
10.7 Reset Swinger Bypass............................................................................................20
10.8 Time Changes.......................................................................................................21
10.9 Keypad Input ........................................................................................................21
Output Options............................................................................................... 22
11.1 Output Options .....................................................................................................22
11.2 CutoOutputs ......................................................................................................22
11.2.1 OutputCutoTime ...............................................................................................22
11.3 Communication Failure Output ...............................................................................22
11.4 Armed Output.......................................................................................................22
11.5 Remote Arming Output..........................................................................................22
11.6 Heat Saver Temperature ( CellCom Z-LTE-V only).......................................................22
11.7 Cool Saver Temperature ( CellCom Z-LTE-V only) .......................................................22
Area Information............................................................................................ 23
12.1 Area Information...................................................................................................23
12.2 Area Number ........................................................................................................23
12.3 Area Name ...........................................................................................................23
12.4 Automatic Arming .................................................................................................23
12.4.1 Bad Zones ............................................................................................................23
12.5 Automatic Disarming .............................................................................................23
Zone Information ........................................................................................... 24
13.1 Zone Information ..................................................................................................24
13.2 Zone Number........................................................................................................24
13.3 Zone Name...........................................................................................................24
13.4 Zone Type ............................................................................................................24
13.5 Area Assignment ...................................................................................................24
13.6 Arming Zone Assignment .......................................................................................24
13.7 Style ....................................................................................................................24
13.8 Next Zone.............................................................................................................25
13.9 Alarm Action .........................................................................................................25
13.10 Disarmed Open .....................................................................................................25

CellCom -LTE-V Installation and Programming Guide Digital Monitoring Products
v
TABLE OF CONTENTS
13.11 Message To Transmit .............................................................................................25
13.12 Output Number.....................................................................................................25
13.13 Output Action .......................................................................................................25
13.14 Swinger Bypass.....................................................................................................26
13.15 Cross Zone ...........................................................................................................26
13.16 Receiver Routing ...................................................................................................26
13.17 Zone Number........................................................................................................26
Stop ................................................................................................................ 27
14.1 Stop.....................................................................................................................27
Set Lockout Code............................................................................................ 28
15.1 Set Lockout Code ..................................................................................................28
Z-Wave Setup (Model CellComZ-LTE-V Only) ................................................ 29
16.1 Add Z-Wave Devices (ADD)....................................................................................29
16.2 List Z-Wave Devices (LIST) ....................................................................................29
16.3 RENAME Z-Wave Devices .......................................................................................30
16.4 STATUS of Z-Wave Devices ....................................................................................30
16.5 Remove Z-Wave Devices (REMOVE)........................................................................30
16.6 Favorites (FAV) .....................................................................................................30
16.7 Adding a FAVORITE...............................................................................................31
16.8 ADD Devices to FAVORITES ...................................................................................31
16.9 Device Settings in FAVORITES................................................................................31
16.10 EDIT Devices in FAVORITES...................................................................................32
16.11 REMOVE Devices from FAVORITES .........................................................................32
16.12 Transfer Controller (XFER) .....................................................................................32
16.13 Optimize (OPT) .....................................................................................................33
Appendix ........................................................................................................ 34
17.1 False Alarm Reduction ...........................................................................................34
17.2 Diagnostics Function .............................................................................................34
17.3 Using the 984 Command Function ..........................................................................35
17.4 Using the Walk Test...............................................................................................35
17.5 Cross Zoning.........................................................................................................36
17.6 Z-Wave Information...............................................................................................36
17.7 Zone 4 Bell Cadence Information............................................................................36
17.8 Remote Arming/Disarming for Ademco Vista Control Panels .....................................37
17.9 Ademco Vista 20P to CellCom-LTE-V for Remote Arming/Disarming...........................38
17.10 DMP XRSuper6 to CellCom-LTE-V for Remote Arming/Disarming...............................38
Specications ................................................................................................. 40
Dimensions and Color..................................................................................... 40
Certications .................................................................................................. 40

Digital Monitoring Products CellCom- LTE-V Installation and Programming Guide
vi
TABLE OF CONTENTS

CellCom -LTE-V Series Installation and Programming Guide Digital Monitoring Products
1
INTRODUCTION
CellCom-LTE-V™ Series Universal Alarm Communicator
Description
The CellCom-LTE-V Series Universal Alarm Communicator provides a fully supervised alarm communication path for any
burglary, commercial re or residential re control panel. The CellCom-LTE-V Series can be connected to a control panel’s
dialer output and used to capture Contact ID messages based on SIA DC-05-1999.09-DCS. The c ommunicator also provides
four input zones and two open-collector outputs for connection to burglary, commercial re or residential re control
panel outputs, and zones. The CellCom-LTE-V’s Zone 4 allows a connection to the bell output of an existing control panel.
The communicator operates in a variety of applications: CID Dialer Connection, Zones 1-4 Input Connections, or Zone 4 Bell
Connection (See Applications on page 5). The CellComZ-LTE-V includes an onboard Z-Wave controller for home automation
applications. The CellComF-LTE-V Fire Alarm Communicator includes a red enclosure and a Model 685-R (Red) Back Box.
What is Included
The CellCom-LTE-V Series Universal Alarm Communicator includes the following:
• PCB with Enclosure
• Hardware Pack
• External Antenna
System Components
SYSTEM COMPONENTS
+DC-
Figure 1: CellComLTE-V Series
Communicator System Components
Power Connection
Terminals
Zones 1-4
Open-Collector
Outputs
Programming
Connection
Tamper
Reset Button
Load Button
Backlit Logo,
Power/Armed LEDs
4 Mounting
Holes in gray
SMA Connector
Antenna
Cell Modem

Digital Monitoring Products CellCom- LTE-V Series Installation and Programming Guide
2
1.1 Terminals
Power Connection Terminals
Power is provided from the Nominal 12VDC auxiliary output of the control panel for CellCom-LTE-V Series
Universal Alarm Communicators. The CellComF-LTE-V Series may be powered from the 12VDC or 24VDC auxiliary
output of the control panel. Observe Polarity (See Figure 1 and Backlit Logo) and use 18-22 AWG wire to connect
the communicator terminal +12 to the +12 or +24V positive terminal on the control panel auxiliary output . Next,
connect the communicator terminal G (ground) to the negative terminal on the control panel auxiliary output.
Control Panel Standby Power
During a power outage, the CellCom-LTE-V draws power from the control panel’s backup battery. The CellCom-
LTE-V must be included in the standby battery calculations for the control panel.
Zones 1-4
Terminals Z1 to Z3, G (ground), Z4+ and Z4- provide four zones to connect to individual relay outputs on
the control panel. Zone 4 (Z4+ and Z4-) can be connected to the control panel bell output. See Zone 4 Bell
Connection.
Open-Collector Outputs
The two outputs, terminals O1 and O2 (see Figure 1), can be programmed to indicate the activity of the zones
or conditions occurring on the system. Open-Collector outputs do not provide a voltage but instead switch-to-
ground the voltage from another source. Maximum voltage is 30 VDC at 50 mA. The outputs can respond to any of
the conditions listed below:
• Activation by zone condition: Steady, Pulse, Momentary, or Follow
• Communication
• Armed area annunciation
• Remote Arming Output
Dialer Connection
Directly connect the Telco phone line (tip and ring) from the control panel to the terminal R (Ring) and one into
T (Tip) (See CID Dialer Connection).
1.2 Programming (PROG) Connection
A 4-pin PROG header is provided to connect a keypad when using a DMP Model 330 Programming Cable. This
provides a quick and easy connection for programming the c ommunicator. For 24 VDC applications using the
CellComF-LTE-V, connect the keypad using a Model 330-24 4-wire programming harness with an in-line resistor.
After programming is complete, remove the keypad.
Caution: If connecting to a 24VDC control panel, do not connect a keypad using a Model 330 harness.
1.3 Tamper
The TAMPER is pressed when the cover of the communicator is secured onto the enclosure. When the cover is
removed, the communicator sends a Tamper Trouble message to the Central Station.
1.4 Reset Button
The RESET button is located on the right side of the circuit board and is used to reset the communicator
microprocessor. After resetting the communicator, begin programming within 30 minutes. If you wait longer than
30 minutes, reset the communicator again.
1.5 Load Button
The CellCom-LTE-V Series Universal Alarm Communicator rmware can be updated via the PROG header.
Caution: Do not connect a Model 400 to the CellComF-LTE-V if using 24 volt power.

CellCom -LTE-V Series Installation and Programming Guide Digital Monitoring Products
3
To update the communicator with a new rmware version, complete the following steps at the protected
premise:
399 Programming Cable
1. Connect a DMP 399 Cable from the PROG Header to the serial port of your PC operating Remote Link and
containing the communicator RU le.
2. Start Remote Link and create or open the account that matches the communicator to be updated.
3. Set the Connection Information Type to Direct with a baud rate of 38400 and choose the appropriate
COM port.
4. Select Panel>Remote Update, then select the correct RU le for the communicator.
5. Press and hold the LOAD button, then press and release the RESET button.
6. Release the LOAD button and click <Update> in Remote Link.
7. After the rmware update is completed, remove the 399 cable and press the RESET button to resume
normal operation.
Model 400 USB Flash Module
1. Press and hold the LOAD switch. While holding the LOAD switch, press and release the RESET switch
2. Release the LOAD switch.
3. Connect the USB ash drive containing the .RU le to the Model 400 and connect the assembly to the
CellCom-LTE-V PROG header. The LED on the Model 400 will ash then display steady green.
4. Press and release the LOAD button on the Model 400 to initiate the rmware update. The LED on
the Model 400 will ash slowly. If the LED displays fast ashes it means the rmware update was
unsuccessful.
5. The update will take approximately 4.5 minutes and when complete the LED on the Model 400 will
display steady green.
6. Press and release the RESET switch then remove the Model 400 assembly.
1.6 Backlit Logo
The backlit logo indicates the Power and Armed status of the communicator. Depending on the operation, the
LED displays in Red or Green as listed in the Table 1. The LED indicates the armed state and status of the system
primary power.
Color and Activity Operation
Green Steady Communicator Disarmed, Primary Power OK
No Light No Power
Red Steady Communicator Armed, Primary Power OK
Table 1: LED Status

Digital Monitoring Products CellCom- LTE-V Installation and Programming Guide
4
INSTALLATION
Mount the CellCom-LTE-V Series Communicator
2.1 Select a Location
Install the communicator away from metal objects. Do not mount the communicator inside or on a control panel
metal enclosure. Mounting the communicator on or near metal surfaces impairs cellular and Z-Wave wireless
performance.
2.2 Mount the Communicator
The communicator should be mounted to a wall using the included #6 screws in the four mounting holes. See
Figure 1. Mount the communicator in a secure, dry place to protect the communicator from damage due to
tampering or the elements. It is not necessary to remove the PCB when installing the communicator.
When connecting component wires, route all wires so they will not interfere with the TAMPER switch. See Figures
2 and 3 for wire routing options.
Replace the housing cover on the mounted base. Be sure to not damage any PCB components when removing or
replacing the housing cover.
2.3 Connect the Antenna
Place the antenna onto the SMA connector. See Figure 1. Twist the antenna until it is securely tightened.
Figure 3: Wire Routing Option Two
+DC-
+DC-
Figure 2: Wire Routing Option One

CellCom -LTE-V Installation and Programming Guide Digital Monitoring Products
5
APPLICATIONS
Applications
The CellCom-LTE-V Series Communicator can be used in a variety of applications.
3.1 CID Dialer Connection
Connect the tip and ring from the control panel directly to the communicator to capture Contact ID messages
that are based on the SIA communication standard DC-05-1999.09-DCS. These messages are then formatted into
a Serial 3 message and sent to a DMP Model SCS-1R or SCS-VR Receiver. CID Dialer Connection cannot be used
when using Zone 4 Bell Connection. Do not connect telephone company wires to the communicator. Remove any
connected telephone company wires from the control panel. See Figure 4.
3.2 Zones 1 - 4 Input Connection
Connect each control panel relay output to a CellCom-LTE-V Series Communicator zone. For programming
purposes, the zone numbers are 1-4. See Figure 5 for Burglary wiring details or Figure 6 for Fire wiring details.
The following are examples of how you might use this application for a burglary or re alarms:
Burglary
Use a normally closed output on a burglary control panel to indicate a burglary alarm. The communicator zone
should be programmed with a Zone Name and Burglary Zone Type. When the output on the control panel turns on
and trips the communicator zone, a message will be sent to an SCS-1R or SCS-VR receiver at the Central Station.
The zone name programming could be used to describe which control panel zone indicated a burglary.
Note: Zone 4 can only be used as a standard input zone when not programmed as zone type Auxiliary 2 (A2). See
Zone 4 Bell Connection.
Use 18-22 AWG for
Power Supply connection
Z3 + Z4 + Z4 - GND
12VDC Aux. Output +
-
Ground
Burglary
Control Panel
The panel or separate power
supply must be 12 Volt Regulated
and Power Limited.
Z1 + Z2 +
RESET
S1
LOAD
S2
PROG
S N
+12 G Z1 Z2 Z4-Z4+GZ3 RTO2O1
RB
Normally Open
Common
Normally Closed
Normally Open
Common
Normally Closed
Normally Open
Common
Normally Closed
Normally Open
Common
Normally Closed
J8
J9
S1
S2
S3
1k ohm
1k ohm
1k ohm
1k ohm
MODEL
CellComSLC
Figure 5: CellCom-LTE-V Series Wiring Diagram for Burglary Zones 1-4
Figure 4: CellCom-LTE-V Series Wiring Diagram for Tip and Ring Connection
Use 18-22 AWG for
Power Supply connection
CONTROL PANEL TIP
CONTROL PANEL RING
12VDC Aux. Output +
-
Ground
Control Panel
The panel or separate power
supply must be 12 Volt Regulated
and Power Limited.
Telephone
Jack
Connector
BELL -
BELL +
RESET
S1
LOAD
S2
BAT
S N
+12 G Z1 Z2 Z4-Z4+GZ3 RTO2O1
RB
J8
J26
J9
S1
S2
S3
MODEL
CellComSLC

Digital Monitoring Products CellCom- LTE-V Installation and Programming Guide
6
APPLICATIONS
Fire
Use a normally open output on a re control panel to indicate a re alarm. The CellComF-LTE-V Series zone
should be programmed with a Zone Name and Fire Zone Type. When the output on the control panel turns on and
trips the CellComF-LTE-V Series zone, a message will be sent to an SCS-1R or SCS-VR receiver at Central Station.
The zone name programming could be used to describe which control panel zone indicated a re. See Figure 6.
3.3 Zone 4 Bell Connection
Zone 4 (Z4+ and Z4-) can be connected to the control panel bell output. This zone detects an alarm condition
on the control panel by monitoring the voltage and cadence timing of the bell output. See Zone 4 Bell Cadence
Information in the Appendix for cadence timing. To enable alarm detection operation, Zone 4 Bell Connection
must be programmed as Zone Type (A2) in Zone Information programming. The type of Cadence sent to the
communicator, the Zone Number, and type of message sent to the SCS-1R or SCS-VR receiver are listed in Table 2.
Zones 5 and 6 are automatically generated by the communicator, using Zone 4’s Zone Name to send to the
Central Station. Zones 5 and 6 cannot be preprogrammed in Zone Information. CID Dialer Connection cannot be
used when using Zone 4 Bell Connection. See Figure 7.
Bell Cadence Zone Number Type of Message
Steady Zone 4 Burglary
Pulse or Temporal 3 Zone 5 Fire
Temporal 4 Zone 6 Emergency or Carbon Monoxide
Use 18-22 AWG for
Power Supply connection
Z3 + Z4 + Z4 - GND
12VDC Aux. Output +
-
Ground
Fire
Control Panel
The panel or separate power
supply must be 12 Volt Regulated
and Power Limited.
Z1 + Z2 +
RESET
S1
LOAD
S2
PROG
S N
+12 G Z1 Z2 Z4-Z4+GZ3 RTO2O1
RB
Normally Open
Common
Normally Closed
Normally Open
Common
Normally Closed
Normally Open
Common
Normally Closed
Normally Open
Common
Normally Closed
J8
J9
S1
S2
S3
1k ohm
MODEL
CellComSLC
1k ohm
1k ohm
1k ohm
Figure 6: CellComF-LTE-V Series Wiring Diagram for Fire Zones 1-4
Table 2: Message Breakdown

CellCom -LTE-V Series Installation and Programming Guide Digital Monitoring Products
7
Use 18-22 AWG
for Power Supply
connection
Z4 + Z4 -
DMP Panel
MODEL CellCom-LTE-V
PROG
+12 G Z1 Z2 Z4-Z4+GZ3 RTO2O1
RB
J8
J9
S3
12VDC Aux. Output
+
-
Use 18-22 AWG
for Power Supply
connection
Z4 + Z4 -
ADEMCO Panel
PROG
+12 G Z1 Z2 Z4-Z4+GZ3 RTO2O1
RB
J8
J9
S3
12VDC Aux. Output
+
-
BELL -
12VDC BELL +
Use 18-22 AWG
for Power Supply
connection
Z4 + Z4 -
NAPCO Panel
PROG
+12 G Z1 Z2 Z4-Z4+GZ3 RTO2O1
RB
J8
J9
S3
12VDC Aux. Output
+
-
BELL -
12VDC BELL +
Use 18-22 AWG
for Power Supply
connection
Z4 -
DSC Panel
PROG
+12 G Z1 Z2 Z4-Z4+GZ3 RTO2O1
RB
J8
J9
S3
12/24VDC Aux. Output
+
-
BELL -
12/24VDC BELL +
10k ohm
1k ohm (for Supervision)
1k ohm
1k ohm
1k ohm
1k ohm (for Supervision)
2.2k ohm (for Supervision)
Program Zone 4
DO - Alarm
AO - Alarm
Voltages above 1.4VDC
are considered Alarm
Voltages above 1.4VDC
are considered Alarm
Voltages above 1.4VDC
are considered Alarm
Voltages below 0.7VDC
are considered Alarm
Z4 + Z4 -
24VDC Panel
PROG
+12 G Z1 Z2 Z4-Z4+GZ3 RTO2O1
RB
J8
J9
S3
1k ohm
Voltages above 1.4VDC
are considered Alarm
1k ohm
Use 18-22 AWG
for Power Supply
connection
12/24VDC Aux. Output
+
-
BELL -
24VDC BELL +
4.7k ohm (for Supervision if required)
MODEL CellCom-LTE-V
MODEL CellCom-LTE-V
MODEL CellCom-LTE-V
MODEL CellCom-LTE-V
Figure 7: Zone 4 Bell Connection
APPLICATIONS

Digital Monitoring Products CellCom- LTE-V Series Installation and Programming Guide
8
3.4 Ademco/Honeywell ECP Connection
A CellCom-LTE-V can be connected to the ECP Bus of an Ademco/Honeywell panel. Table 3 and Figure 8 detail the
necessary wiring connections for the CellCom-LTE-V to communicate with the Ademco/Honeywell ECP Bus.
CellCom-LTE-V to ECP Wiring
CellCom-LTE-V Ademco/Honeywell ECP Bus
+12 Keypad Power
G Keypad GND
Z4+ Data Out
Z4- Data In
Table 3: CellCom-LTE-V to Ademco/Honeywell ECP Pinout
APPLICATIONS
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
++-
HI HI HI
LO LO LO LO
HI HI
LO LO
HI HI
LO LO
HI
TIP
(BROWN)
RING
(G R AY )
TIP
(GREEN)
RING
(RED)
+-
BLACK
RED
SYNC
COM
DATA
(USE SA4120XM-1
CABLE)
1 2 3 4 5 6 7 8
OUT 17 +12 AUX GND OUT 18
VISTA 20P ONLY
Ademco Vista 20P
+DC-
Figure 8: Ademco Vista 20P ECP to CellCom-LTE-V
ECP operation must be enabled when programming the CellCom-LTE-V. See Keypad Input in System Options for
additional information. When connected as shown in Figures 8 and 9, the communicator provides the following
operations listed below:
• Arm and disarm the Ademco/Honeywell panel for Stay/Away systems using the Virtual KeypadTM App and
VirtualKeypad.com.
• Receives alarm, trouble, and opening/closing messages from the panel and sends them to the Central
Station.
• Add, delete, and change user codes in the Ademco/Honeywell panel.

CellCom -LTE-V Series Installation and Programming Guide Digital Monitoring Products
9
Accessing Programming on the Ademco/Honeywell Panel
The Installer code may be changed in Ademco/Honeywell panels. A new 4-digit Installer code may be entered.
If the Installer code is not known, use the following steps to access Programming in the Ademco/Honeywell panel
without an Installer code:
1. Power down and then power up the Ademco/Honeywell panel.
2. Within 1 minute of powering up the Ademco/Honeywell panel, simultaneously press and hold the # and *
buttons on the keypad.
3. The keypad displays Programming.
Conguring Communication with the Ademco/Honeywell Panel and the CellCom-LTE-V
The following steps describe how to congure Ademco/Honeywell control panels to communicate with the
communicator.
1. Program Position * 54: Enter 0. (No signaling delay)
2. Program Position * 55: Enter 1 (Enables communication to CellCom-LTE-V).
3. Program Position * 65: Enter 0 (To turn o Opening Reports).
4. Program Position * 66: Enter 0 (To turn o Closing Reports).
5. Program Position * 84: Enter 0 (To disable CP01 and allow remote Arm Away).
6. Program Position * 193: Enter 1 0 (Enables CellCom-LTE-V ECP Bus address).
In the event the Ademco/Honeywell panel fails to communicate with the CellCom-LTE-V, program Position * 29 to
enable the long range radio on the Ademco/Honeywell panel.
User Codes in the Ademco/Honeywell Panel
Because the communicator duplicates the panel’s user codes, existing user codes in the Ademco/Honeywell
panel, including Master, must be added to the communicator. Any new user codes added to the communicator
from the Virtual Keypad App will be automatically entered in the Ademco/Honeywell panel. Master level users
cannot be added to the Ademco/Honeywell panel from the communciator.
User codes from the Ademco/Honeywell panel that are designated as Master or Partition Master should be
congured as Master codes in the communicator.
If the Ademco/Honeywell panel is armed/disarmed from a keypad, the communicator reports an opening/closing
message by user 0 to the Central Station.
When the communicator is armed by the Virtual Keypad App or VirtualKeypad.com, the Ademco/Honeywell panel
is also armed and the communicator reports an opening message. If opening and closing reports are enabled in
the Ademco/Honeywell panel a duplicate message will also be sent to the Central Station.
3.5 Using Outputs for Communication Failure
When a CellCom-LTE-V is connected as shown in Figure 9 and the programmed output turns on and trips the
control panel zone, a communication failure is indicated at the control panel noties the user. Program the
output number (O1 or O2) in Communication Failure Output within the Ouput Options programming menu. See
Communication Failure Output for programming instructions and see Figure 9 for wiring instructions.
APPLICATIONS
Note: Use 18-22 AWG for Power Supply connection
12VDC Aux. Output
+
-
CellCom-LTE-V
PROG
+12 G Z1 Z2 Z4-Z4+GZ3 RTO2O1
NO
RB
GND
Zone 1
Zone 2
Control Panel EOL resistor
NC C NEG-
NO NC C POS+
Control Panel
Relay
Module
Figure 9: Communication Failure Zone Connection

Digital Monitoring Products CellCom- LTE-V Series Installation and Programming Guide
10
REMOTE ARMING AND DISARMING
Remote Arming and Disarming
4.1 Virtual Keypad App and VirtualKeypad.com
Using a Smartphone with the DMP Virtual Keypad App or using a computer with VirtualKeypad.com, you can
connect to the CellCom-LTE-V Series Communicator to arm Areas, turn Outputs on and o, and add, edit or
remove Users. When using the CellComZ-LTE-V, you can control Z-Wave devices, Favorites and Rooms. See Figure
10.
4.2 Using Outputs to Arm and Disarm
A burglary control panel zone may be programmed as an arming zone and connected to a CellCom-LTE-V output
O1 or O2. See Figure 11. Program the output number in Armed Output or Remote Arming Output in Output
Options when programming the communicator. See Armed Output or Remote Arming Output. The communicator
output connections can be used with any of the applications listed in Applications Section.
Figure 10: Virtual Keypad Application can be used to access the CellCom-LTE-V Communicator.
Use 18-22 AWG for
Power Supply connection
O1 O2
12VDC Aux. Output
+
-
Control Panel
MODEL CellCom-LTE-V
PROG
+12 G Z1 Z2 Z4-Z4+GZ3 RTO2O1
RB
GND
Zone 1
Zone 2 Control Panel EOL resistor
Figure 11: Burglary Control Panel Zones Connected to the CellCom-LTE-V
Outputs to Arm and Disarm the Burglary Control Panel

CellCom -LTE-V Series Installation and Programming Guide Digital Monitoring Products
11
PROGRAMMING INTRODUCTION
Programming the CellCom-LTE-V Series Universal Alarm Communicator
5.1 Before You Begin
Before beginning programming, we recommend you read through the contents of this guide. The information in
this guide allows you to quickly learn the programming options and operational capabilities of the CellCom-LTE-V
Series Universal Alarm Communicator.
After this Introduction, the remaining sections describe the functions of each programming menu items along
with their available options. The communicator contains all of its programming information in an on-board
processor and does not require an external programmer.
In addition to this manual, you should also be familiar with the following documents:
• CellCom-LTE-V Series Universal Alarm Communicator User Sheet (LT-1819)
• CellCom-LTE-V Series Universal Alarm Communicator Programming Sheet (LT-1818)
Programming Sheet
Included with each communicator is the CellCom-LTE-V Series Programming Sheet (LT-1333).The programming
sheet lists the various options available for programming the communicator. Before beginning programming,
completely ll out the programming sheet with the programming options you intend to enter into programming.
Having the completed the programming sheet available to you while entering data helps to prevent errors and
can shorten the length of time you spend programming. Completing the programming sheet also provides you
with an accurate account of the communicator’s program that you can keep on le for future system service or
expansion.
5.2 Getting Started
Initializing the Communicator
When programming a communicator for the rst time or rewriting the entire program of an existing
communicator, use the Initialization programming option described in Section 6. Initializing clears the
communicator’s memory of all data and sets the highest numbered user number to user code 99.
Accessing the Programmer
To access the programmer function of the communicator :
1. Connect the keypad to the PROG header
2. Press and release the RESET button.
3. Enter the code 6653 (PROG) and the keypad displays PROGRAMMER.
5.3 Programming Menu
You are now ready to start programming the CellCom-LTE-V Series Universal Alarm Communicator. Press the CMD
key to advance through the programming menu items listed in Table 4. To select a menu item for programming,
press any select key or area when the desired menu item displays on the keypad. The detailed instructions for
each programming step are found in this guide.
Menu Item Section in This Manual Menu Item Section in This Manual
Initialization 6 Output Options 12
Communication 7 Area Information 13
Messaging Setup 8 Zone Information 14
Remote Options 9 Stop 15
System Reports 10 Set Lockout Code 16
System Options 11 Z-Wave Setup 17
Table 4: Programming Menu Items

Digital Monitoring Products CellCom- LTE-V Series Installation and Programming Guide
12
5.4 Reset Timeout
The CellCom-LTE-V Series Universal Alarm Communicator has a feature that requires you to enter the
Programmer menu within 30 minutes of resetting the communicator. After 30 minutes, if you attempt to program
by entering the 6653 (PROG) code, the keypad displays: RESET PANEL. You must reset the communicator and
enter the program code within the next 30 minutes.
If you are already in the Programmer menu and do not press any keys on the programming keypad for 30 minutes,
the communicator exits programming. All data entered up to that point is saved in the communicator memory.
To exit the communicator’s Programmer menu, you must use the STOP function. The STOP option is the second to
the last option in programming. The STOP function disarms all areas. The programming session is then terminated
and the keypad returns to the Status List or Main Screen.
5.5 Special Keys
The following keys and areas are common to all DMP LCD and graphic touchscreen keypads.
CMD (command)
Pressing CMD allows you to advance through the programming menu and through each step of a programming
sec tion. As you advance through the programming menu, the keypad display any current programming already
stored in the communicator memory. If no change is required for an option, press CMD to advance to the next
step.
CMD is also used to enter information into the communicator’s memory such as an IP address or a Zone Name.
Press CMD after entering information.
<— (back arrow)
Use the back arrow to back up one step while programming. The Back Arrow key is also used when an error is
made while entering in formation. Press the Back Arrow key once to erase the last character entered.
Select Keys and Areas
The top row of keys on LCD Keypads are called the select keys. Graphic touchscreen keypads have select areas.
When you need to press a select key or area, the keypad displays the function or options above one of the keys
or areas. For example, you can enter AM or PM when programming the automatic test time or answer YES or NO
for a system option.
During programming, the select keys and areas also allow you to change infor mation currently in communicator
memory by pressing the appropriate select key or area under or on the display. You then enter the new
information using the keypad data entry digit keys.
When there are more than four re sponse options avail able, press CMD to display the next one to four options.
Pressing the back arrow allows you to review the previous four choices.
Select keys and areas are also used for selecting a section from the pro gramming menu. Press any select key or
area when the programming section name you want select, displays.
LCD Keypads
When instructed to press the rst select key, press the far left select key; the second select key is the second
from the left; third select key is second from the right; and the fourth select key is the far right key. See Figure
12.
Graphic Touchscreen Keypads
When instructed to press the rst select area, touch Select Area 1; the second select area touch Select Area 2;
third select area touch Select Area 3; and the fourth select area touch Select Area 4. See Figure 13.
PROGRAMMING INTRODUCTION
Figure 12: LCE Keypad Select Keys Figure 13: Graphic Touchscreen Keypad Select Areas
First Letter
Second Letter
Third Letter
Special Character
(CBA
32-Character Display
Select Area 1
Select Area 3
Select Area 2
Select Area 4

CellCom -LTE-V Series Installation and Programming Guide Digital Monitoring Products
13
PROGRAMMING INTRODUCTION
5.6 Entering Letters and Special Characters
Some options during programming require you to enter Letters and Special Characters. Use the Number Pad
directions below to enter letters and special characters on a number pad or use the Standard Keyboard directions
to enter letters and special characters on a standard keyboard.
Number Pad
1. Choose a character from Table 5.
2. Identify the Number the character correlates with and press that number on the number pad.
3. Identify the Select Key or Area for that character and press that select key or area on the keypad. To
access the lowercase letter, press that select key or area again.
4. When the desired character displays on the keypad, return to Step 1 to enter another character or press
CMD if nished.
Number Select Key 1 Select Key 2 Select Key 3 Select Key 4
1 A B C (
2 D E F )
3 G H I !
4 J K L ?
5 M N O /
6 P QR &
7 S T U @
8 V W X ,
9 Y Z space _
0 - . * #
Standard Keyboard
• Press ABC to access uppercase letters.
• Press abc to access lowercase letters.
• Press !@# to access symbols and special characters.
• Press 123 to access the number pad.
5.9 Keypad Displays Current Programming
Each programming option displayed at the keypad shows the currently selected option in the communicator
memory. These options are either shown as a number, a blank, or a NO or YES. To change a number or blank
to a new number, press any top row select key or area. The current option is replaced with a dash. Press the
number(s) on the keypad you want to enter as the new number for that option. It is not necessary to enter
numbers with leading zeros. The communicator automatically right justies the number when you press CMD.
To change a programming option that requires a NO or YES response, press the select key or area for the
response not selected.
For example, if the current option is selected as YES and you want to change it to NO, press the third top row
select key on LCD keypads. On graphic touchscreen keypads, touch select area 3. The display changes to NO.
Press CMD to display the next option.
Table 5: Entering Letters and Special Characters in the Number Pad

Digital Monitoring Products CellCom- LTE-V Series Installation and Programming Guide
14
INITIALIZATION
Initialization
6.1 Initialization
This function allows you to set the communicator’s programmed memory back to the
factory defaults in preparation for system programming.
After selecting YES to clear a section of memory, the communicator asks if you are sure
you want to clear the memory. This is a safeguard against accidently erasing part of your
programming. No memory is cleared from the programming until you answer YES to the
SURE? YES NO option.
6.2 Clear All Codes
NO leaves existing codes intact.
YES clears the user code memory and assigns the user code number 99 to user 20.
6.3 Clear All Schedules
NO - Leaves existing schedules intact.
YES - Clears all schedules from the programming.
6.4 Clear Events
NO leaves existing event memory intact.
YES clears all event memory currently held in the communicator’s Display Events buer.
6.5 Clear Zone Programming
NO leaves existing zone information intact.
YES sets all zones in the system to * UNUSED *
6.6 Clear Communication
NO - Leaves existing communication programming intact.
YES - Clears communication to factory defaults.
6.7 Set to Factory Defaults
NO leaves the remainder of the existing communicator programming intact.
YES sets the communicator programming back to factory default selections and clears
all Z-Wave device programming and Favorites from the communicator. Selecting YES
does not clear the event memory, zone, user code information, or schedules.
INITIALIZATION
CODES? NO YES
SURE? YES NO
SCHEDS? NO YES
SURE? YES NO
EVENTS? NO YES
SURE? YES NO
ZONES? NO YES
SURE? YES NO
COMMS? NO YES
SURE? YES NO
DEFAULTS? NO YES
SURE? YES NO
CODES? NO YES
SCHEDS? NO YES
For each section of the panel program you can
initialize, a NO or YES option is provided.
Selecting YES advances you to
a confirmation prompt.
If you select YES, the panel initializes that section of
the program and advances you to the next prompt.
If you select NO, the panel advances you to the next
section prompt but does not initialize that section of
the program.
SURE? YES NO
Selecting NO
advances you to
the next prompt.
Figure 14: Alternating Yes and No Options