DMP Electronics 7800 Series User manual

7800 Series Graphic Touchscreen Keypad
Quick Start Guide
Step 1: Remove the Cover
Insert a slotted-tip screwdriver into one of the slots on the bottom of the keypad and lift the screwdriver upward. Repeat with the other
slot. Separate the cover from the base and set the cover containing the keypad components aside.
Step 2: Wire the Keypad
1. Connect the harness to the keypad header.
2. Connect the red wire to panel terminal 7.
3. Connect the yellow wire to panel terminal 8.
4. Connect the green wire to panel terminal 9.
5. Connect the black wire to panel terminal 10.
6. For 7873/7873H keypads, use a 5-wire
harness for external card reader connection.
Use 1k Ohm EOL resistors DMP Model 311 on keypad
zones 1-4.
Full Installation and Programming Guide
To view the full 7800 Series Graphic Touchscreen Keypad Installation and Programming Guide, scan this QR code or
visit DMP.com.
This quick start guide walks you through installing the keypad.

 
 












Armed/Power LEDs &
Proximity Reader
Dealer Logo Carousel Menu
Local
Weather
Interactive
Arming/
Disarming
Shield Press the
Navigation
Arrows or touch
and drag the
menu to scroll
microSD
Card Slot
1k Ω
1k Ω
1k Ω
1k Ω
Violet - Door Strike, Normally Closed
Gray - Door Strike, Common
Orange - Door Strike, Normally Open
Black - Ground
Green - Receive Data
To Panel
Keypad Bus
To Door Strike
Keypad
Back
Reader
Yellow - Send Data
Red - Power
Black - Ground
Red - Power
White/Green - Reader Data 0
White/Brown - Zone 1
White/Red - Zone 2
White/Orange - Zone 3
White/Yellow - Zone 4 White - Reader Data 1
Step 3: Wire for Access Control (Optional)
For wiring for access control, see the QR code at the beginning of the document.

18205
LT-2579 22142
INTRUSION • FIRE• ACCESS• NETWORKS
2500 North Partnership Boulevard
Springfield, Missouri 65803-8877
Domestic: 800.641.4282 | International: 417.831.9362
DMP.com
© 2022
Step 6: Mount the Keypad
All DMP keypad housings are designed to install on any 4” square box, 3-gang
switch box, compatible backboxes, or directly on a flat surface.
1. Ensure all cables are routed through the keypad base cut outs before fully
mounting the base to the wall.
2. Use #6 screws to secure the keypad base to the surface.
3. Place the keypad cover back onto the base and snap into place.
Step 7: Program the Panel and Keypad
For all programming instructions, see the QR code at the beginning of the document.
Step 8: Test the Keypad
For all testing instructions, see the QR code at the beginning of the document.
Step 4: Wire the Electronic Lock
The Form C relay on 7873/7873H keypads draws up to 15 mA of current and the contacts are rated for 1 Amp at 30 VDC maximum,
resistive. The wires marked NO C NC allow you to connect the device wiring to the relay for module control. Use an additional power
supply to power magnetic locks and door strikes.
Step 5: Wire the 333 Supressor
Use the included 333 suppressor with the keypad to suppress any surges caused by energizing a magnetic lock or door strike. Install the
333 across the keypad C (common) and NO (normally open) or NC (normally closed) wires.
If the device being controlled by the relay is connected to the NO and C wires, install the suppressor on the NO and C wires. Conversely,
if the device is connected to the NC and C wires, install the 333 Suppressor on NC and C wires.
A
A
A
A
BB
C
C C
C
A
B
Mounting holes
Wiring cutouts
CCover latches
Green/White – D0
White – D1
Orange – N/O
Gray – C
Violet – N/C
NC
C
NO
WHT
GRN
None
To Keypad
Magnetic Door Lock
Normally Closed
Normally Closed Normally Open
Common
Power Supply
Model 333
Supressor
NC
C
NO
WHT
GRN
None
To Keypad
Door Strike Relay
Normally Opem
Common
Power Supply
Model 333
Supressor