DMP Electronics 9800 Series User manual

INSTALLATION GUIDE
TODAY
WEDNESDAY
82
98 77
HI LO
CURRENT
98 77
HI LO
9800 Series Wireless
Graphic Touchscreen Keypad

b 9800 Series Keypad Installation Guide
© 2016 Digital Monitoring Products, Inc.
Information furnished by DMP is believed to be accurate and reliable.
This information is subject to change without notice.

9800 Series Keypad Installation Guide 1
DMP Keypad Features
DMP 9800 Series Wireless Graphic Touchscreen Keypads offer exible features and
functionality in a stylish design.
Each keypad provides:
• AC Power/Armed LED
• Full color touchscreen display
• Built-in proximity card reader
• Internal speaker
• Wireless communication
• 12VDC plug-in power supply (9862)
• 5VDC plug-in power supply (9862USB)
• Internal rechargeable 3.7 V lithium battery
• Micro SD for customized logo
• Icon-driven operation
• Wall tamper protection (9862)
• Snap-in deskstand legs (9862USB)
• Optional backboxes for conduit or wall-mount applications
Touchscreen Display
9800 Series Wireless Graphic Touchscreen Keypads have an integrated LCD
touchscreen user interface. The display can be set up to display a custom logo image
on the main screen. See the Custom Dealer Logo section. The display can also be
programmed to turn off (blank screen) during periods when the keypad is not in use.
See Backlighting Brightness under End-User Options.
Warning: DO NOT use any sharp objects to operate the touchscreen such as a pen
or pencil.
Figure 1: Keypad Main Screen
ARMED
TO DAY
WEDNESDAY
Panic
Chime
Check-in
Reset
MON 5:35 AM
82
CURRENT
HI LO
98 77
HI LO
98 77

2 9800 Series Keypad Installation Guide
Select Areas
There are four Select Areas in the display as
seen in Figure 2. These Select Areas are one of
the features that make the system so easy to
operate. They allow you to make selections by
pressing the area over each key, icon, or other
selection to operate the keypad.
Warning: DO NOT use any sharp objects to
operate the touchscreen such as a pen or
pencil.
Panic Icons
Optional Panic functions allow users to send
Police, Emergency, or Fire reports to the central station as seen in Figure 3. You must
enable the Panic function in Installer Options in order to use the Panic Icons. See
Programming Keypad Options later in this document.
Press the panic icon in the carousel menu to bring up the Panic Options menu. This
icon can be seen in Figure 4. Press the panic menu icon for 2 seconds until a beep
is heard. At the beep, the panel sends the following zone alarm reports to the
central station:
Panic - Zone 19 + Device Address
Emergency - non-medical - Zone 29 + Device Address
Fire - Zone 39 + Device Address
Keypad Backlighting
The touchscreen illuminates at the maximum brightness any time the display is
pressed. During an alarm condition, the touchscreen turns Red. When all alarm
conditions are cleared, the user-selected brightness is restored.
Cleaning the Touchscreen Display
To minimize unintended key presses, select the keypad option from the main carousel
menu and clean the touchscreen using a water dampened soft, lint-free cloth. Apply
the water onto the cloth, do NOT apply directly onto the touchscreen. After cleaning,
wipe the touchscreen dry with a soft, lint-free cloth. Touch the blue mini shield that
displays in the upper left corner to return to the Main Screen.
Figure 2: Touchscreen Select Areas
1ABC
5MNO
9YZ
2DEF
6PQR
0
3GHI
7STU
4JKL
8VWX
CMD
Select Area 1 Select Area 2 Select Area 3 Select Area 4
Figure 3 and Figure 4: Graphic Keypad Panic Icons
DISARMED
NOW
TUE
Panic
Chime
Check-in
Reset
MONITOR ON
PANIC OPTIONS
PRESS AND HOLD BUTTON TO SEND
FIRE
POLICE EMERGENCY

9800 Series Keypad Installation Guide 3
Internal Speaker Operation
All keypads emit standard tones for screen presses, entry delay, and system alerts.
The speaker also provides distinct burglary, re, zone monitor, and prewarn cadences.
The keypads provide an alternate prewarn with alarm cadence that occurs when the
status list displays a zone alarm.
Micro SD Card
9800 Series Wireless Graphic Touchscreen Keypads provide a spring-loaded Micro SD
card slot on the right edge of the keypad housing. This is used to load a custom logo
onto the main screen. Insert the Micro SD card straight in, with the contacts facing
the wall, pressing in until a click occurs from the spring mechanism. To remove the
Micro SD card, gently press in to allow the spring to eject the card. Grasp the edges
of the card with two ngers and remove. See Figure 5.
Custom Dealer Logo
To display a custom dealer logo on the main screen, contact DMP Marketing at
1-800-641-4282 or [email protected] for information. To add a custom dealer
logo, see the Dealer Logo option under Installer Options menu.
AC Power/Armed LED Operation
The LED at the top-center of the keypad indicates the keypad power status and
armed status of the panel. Depending on the operation, the LED displays in Red or
Blue as listed in the table.
Internal Card Reader
When a proximity credential is presented to the internal reader, a beep tone is
heard and the Power/Armed LED blinks. This provides both an audible and visual
acknowledgement of the credential read. See Figure 6.
Figure 5: Micro SD Card Slot
Micro SD
Card Slot
ARMED
TODAY
WEDNESDAY
Panic
Chime
Check-in
Reset
MON 5:35 AM
82
CURRENT
HI LO
98 77
80
LO
74
HI
Color and Activity Operation
Blue Steady Panel Disarmed, AC Power OK, Battery OK
Blue Blinking Panel Disarmed, AC Power OK, Battery Fault
No Light Panel Disarmed, AC Power Fault, Battery OK
Red Steady Panel Armed, AC Power OK, Battery OK
Red/Blue Alternate Panel Armed, AC Power OK, Battery Fault
Red Blinking Panel Armed, AC Power Fault, Battery OK
Figure 6: Internal Card Reader Area
Internal Card Reader Area
ARMED
TODAY
WEDNESDAY
Panic
Chime
Check-in
Reset
MON 5:35 AM
82
CURRENT
HI LO
98 77
80
LO
74
HI

4 9800 Series Keypad Installation Guide
End-User Options
All keypads provide three keypad adjustments the end-user can make through a User
Options Menu. The user can also view the keypad model number and address.
Scroll through the carousel menu and press the Options icon until it glows. The screen
displays the available options shown below. See Figure 7 for example.
Backlighting Brightness
Set the backlight illumination and AC Power/Armed LED brightness level. In the
touchscreen display below SET BRIGHTNESS, press the left < to lower and the right
> to raise the backlight brightness. If the brightness level is lowered, it reverts to
maximum intensity whenever the screen is pressed during normal operation. If the
screen is not pressed, and the speaker has not sounded for 30 seconds, the user-
selected standby brightness level restores.
When the keypad is operating only on standby battery power, the backlight brightness
is turned off after 30 seconds. When pressed, the touchscreen reverts to maximum
intensity.
Internal Speaker Tone
Set the keypad speaker tone for screen presses. At the SET TONE display, use the left
< to lower the tone and the right > to raise the tone.
Internal Volume Level
Set the keypad speaker volume level for screen presses, entry delay, and zone
monitor conditions. During alarm, entry delay, and trouble tone conditions, the
volume is always at maximum level. Use the left < to decrease the keypad volume
and the right > to increase the volume.
Model Number
The LCD displays the keypad model number and rmware version and date in the top
right corner of the screen. The user cannot change this information.
Figure 7: Options Screen
BRIGHTNESS
TONE
VOLUME
9800 V109 072214 SN 14500000
INSTALLER
OPTIONS

9800 Series Keypad Installation Guide 5
Keypad Serial Number
For your convenience, an additional pre-printed serial number label is included. Prior to
installing the device, record the serial number or place the pre-printed serial number
label on the panel programming sheet. This number is required during programming.
The keypads can be programmed into the control panel by entering the serial number
in Device Setup panel programming, or alternatively using the wireless keypad
association operation. A maximum of 4 keypads may be used with the panel.
Installing the Keypad
The 9862 keypad housing is designed to easily install on any single-gang switch box or
at surface. Figure 9 shows the keypad housing base mounting hole locations.
Selecting the Proper Location
9800 Series Wireless Graphic Touchscreen Keypads provide
a built-in survey capability in the Installer Options menu to
allow one person to conrm keypad communication with
the panel. See Accessing Keypad Wireless Survey later in
this document.
Remove the Cover
The keypad housing is made up of two parts: the cover,
which contains the circuit board and components, and the
base. Use the following steps to separate the keypad cover
and base:
1. Insert a at screwdriver into one of the slots on the
bottom of the keypad and gently lift the screwdriver
handle toward you while pulling the halves apart.
Repeat with the other slot. See Figure 8.
2. Using your hands, gently separate the front from the
base and set the cover and components aside.
9862
Series
Graphic
Keypad
Building Wall
Insert small
screwdriver and
lift to remove
cover.
Do not twist.
Figure 8: Removing
the Keypad Cover

6 9800 Series Keypad Installation Guide
Wall-Mounting the Keypad (9862)
The 9862 is intended for wall mount installation. Feed the power supply wire through
the case. Secure the keypad base to the wall ensuring that the wall tamper switch
makes proper contact with the wall. Use the supplied screws in the mounting hole
locations as shown in Figure 9.
Attaching the Deskstand (9862USB)
The 9862USB Wireless Graphic
Touchscreen Keypad is intended for
tabletop use.
1. Attach the keypad deskstand by
pressing the slide lock on one
of the stand legs into the hole
located on the back of the
keypad case.
2. Slide the leg upwards until the
top ridge seats in the rectangular
opening. See Figure 10.
3. Repeat the process to attach the
second side of the stand.
Deskstand
Leg
9862 USB
Keypad Case
1
2
Slide Lock
Figure 10: Attaching the Deskstand
Figure 9: 12VDC Wiring
Ribbed Black (+)
Black (-)
Surface and Backbox
Mounting Holes
Keypad Back
Tamper
Keypad Back
+
Model 372-500
DC Plug-in
Power
Supply
_
+

9800 Series Keypad Installation Guide 7
Power Supply (9862)
Figure 9 shows the Model 372-500-W plug-in DC power supply. The 9862 ships with
a separate power supply harness to be connected. The harness may be lengthened,
but should be located within 100 feet of the keypad using 22 AWG wire. For ease of
connection, locate the keypad near a wall outlet.
In addition to powering the keypad, the power supply also charges the internal
back-up battery.
OBSERVE POLARITY
Connect the Smooth Black (-) wire to the negative terminal on the power
supply. Connect the Ribbed Black (+) wire to the positive terminal on the
power supply.
Firmly grasp the wires near the base of the connector and
hold the outside edges of the keypad housing. Connect the
power supply harness to the J5 header on the 9862 Wireless
Graphic Touchscreen Keypad.
Note: Do not remove the PCB from the keypad housing to
install the power supply connector.
When the power supply connector is plugged into the
keypad, the internal battery is automatically connected.
The keypad can operate from battery only as long as the
power supply connector is plugged into the keypad.
Plug the power supply into a 120 Volt AC, 60Hz dedicated
outlet not controlled by a switch.
Power Supply (9862USB)
To connect the 9862USB keypad power supply, follow these steps:
1. Remove the center screw from the outlet plate.
2. Feed the micro USB end of the power supply cable through the two slits in the
transformer strap.
3. Fit the adapter plugs through the square opening in the plastic strap and wrap
the strap around the power supply until the two holes line up. See Figure 12.
J5
Ribbed Black (+) Black (-)
Figure 11: Installing the
Power Supply Harness
Figure 12: 9862USB Power
Supply Connection

8 9800 Series Keypad Installation Guide
4. Plug the USB end of the power supply cable into the USB port on the adapter.
5. Plug the power supply into the outlet.
6. Place the outlet screw through the two holes in the plastic strap and tighten it
into the outlet. See Figure 12.
7. Plug the micro USB end of the cable into the back of the 9862USB keypad. See
Figure 13.
USB end Transformer
Strap
Micro USB Port
Micro USB end
Figure 13: 9862USB Power Supply Keypad Connection