DMX4ALL PixxRangeExtender 12V User manual

PixxRangeExtender 12V
Art.-Nr.: 90-0892 3420

PixxRangeExtender 12V 2
For your own safety, please read this user manual and warnings carefully
before installation.
Soldering work may only be carried out by a certified specialist in order to
prevent damage to the product and injury to people.
If acidic or leaded solder, soldering grease or acidic flux etc. has been
used for soldering and/or if the board has been improperly soldered, all
warranty claims will be voided and no repair will be carried out.
Description
The PixxRangeExtender 12V is an optimal tool to bridge longer distances by using
digital LED-Stripes.
Therefore, the PixxRangeExtender 12V is to connect in front to the signal input of the
digital LED-Stripe.
Digital LED-Stripes with separated DATA- and CLOCK-Signal as well as digital LED-
Stripes with only one DATA-Signal can be combined with the PixxRangeExtender
12V.
Data Sheet
Power supply: 12V from digital LED-Stripe
Connection: 3 pin soldering surface (Signal-Site)
4 pin soldering surface (Digital LED-Site)
Dimensions: 29mm x 12mm
Contents
1x PixxRangeExtender 12V
1x User manual (german and english)

PixxRangeExtender 12V 3
Connection
Connection between Controller and digital LED-Stripe
For other LED stripe types, the connection is made according to the manufacturer's
instructions.
Connection between two digital LED-Stripes
Only digital LED strips with 12V operation voltage of the same type may be
used. Mixing different types is not allowed.
PixxRangeExtender 12V
Digital LED-Stripe
Controller
PixxRangeExtender 12V
Digital LED-Stripe
Controller
Using the LED-Stripe LC8808:
D1 must be connected to GND
Using the LED-Stripe GS8208:
D1 must be open !
PixxRangeExtender 12V
Digital LED-Stripe
Digital LED-Stripe

PixxRangeExtender 12V 4
Compatible digital LED-Stripes
The PixxRangeExtender 12V is compatible with digital LED strips with only one
signal line or separate signal and data line.
These are for example:
- GS8208
- LC8808

PixxRangeExtender 12V 5

PixxRangeExtender 12V 6
CE-Conformity
This assembly (board) is controlled by a microprocessor and
uses high frequency. In order to maintain the properties of the
module with regard to CE conformity, installation into a closed
metal housing in accordance with the EMC directive
2014/30/EU is necessary.
Disposal
Electronical and electronic products must not be disposed in
domestic waste. Dispose the product at the end of its service
life in accordance with applicable legal regulations.
Information on this can be obtained from your local waste
disposal company.
Warning
This device is no toy. Keep out of the reach of children.
Parents are liable for consequential damages caused by
nonobservance for their children.

PixxRangeExtender 12V 7
Risk-Notes
You purchased a technical product. Conformable to the best
available technology the following risks should not excluded:
Failure risk:
The device can drop out partially or completely at any time without warning. To
reduce the probability of a failure a redundant system structure is necessary.
Initiation risk:
For the installation of the board, the board must be connected and adjusted to
foreign components according to the device paperwork. This work can only be
done by qualified personnel, which read the full device paperwork and understand
it.
Operating risk:
The Change or the operation under special conditions of the installed
systems/components could as well as hidden defects cause to breakdown within
the running time.
Misusage risk:
Any nonstandard use could cause incalculable risks and is not allowed.
Warning: It is not allowed to use the device in an operation, where the safety of
persons depend on this device.

DMX4ALL GmbH
Reiterweg 2A
D-44869 Bochum
Germany
Last changes: 08.06.2022
© Copyright DMX4ALL GmbH
All rights reserve. No part of this manual may be reproduced in any form (photocopy, pressure,
microfilm or in another procedure) without written permission or processed, multiplied or spread using
electronic systems.
All information contained in this manual was arranged with largest care and after best knowledge.
Nevertheless errors are to be excluded not completely. It is pointed out that neither a guarantee nor the
legal responsibility or any liability for consequences which are due to incorrect information is assumed. This
document does not contain assured characteristics. The guidance and the features may be changed at any
time and without previous announcement.