Dogtra Edge RT User manual

1
EDGE RT
EXPANDABLE TO 3-DOG SYSTEM
Owner's Manual
Please read this manual thoroughly
before operating the EDGE RT training e-collar.

2
IMPORTANT SAFETY AND PRODUCT
INFORMATION
WARNING
Please read all safety and product information below
before using your Dogtra product. Failure to follow
these safety instructions could result in injury to you,
your dog and others, or it could result in damage to your
Dogtra product or other property.
PRODUCT SAFETY
Training Methods
Dogtra products may be used with a variety of training
methods. However, each dog may have a different reaction
to training methods and to Dogtra products. Closely
observe your dog when determining the right training
method to use with your Dogtra product.
Aggressive Dogs
Do not use Dogtra products with aggressive dogs as such
dogs may react adversely and cause injury to people or
other dogs. Seek the assistance of a dog-training specialist
or veterinarian when dealing with aggressive dogs.
Children
Dogtra products are not toys. Adult supervision and close
attention are necessary when Dogtra products are used by
or near children.
PRODUCT DAMAGE
Electrical Product
Your Dogtra product contains electrical components and
batteries. Do not use or keep your product near heat or
flammable sources. Such use or storage may damage your

3
product and/or cause fire, explosion, injury, or property
damage.
Medical Device Interference
Dogtra products contain electrical and magnetic
components that emit low level electromagnetic waves and
radio frequencies. These electromagnetic waves or radio
frequencies may interfere with pacemakers, defibrillators,
or other medical devices. Consult your physician or
medical device maker before using your medical device
with a Dogtra product. If you think that your Dogtra
product is interfering with your pacemaker, defibrillator,
or other medical device, stop using the Dogtra product.
Inadvertent Activation
The digital microprocessor offers thousands of unique
codes to eliminate frequency match-up with other Dogtra
e-collars. The Constant button will automatically shut
down after being held down for 12 seconds or more as a
safety feature.
UNAUTHORIZED USE
Your Dogtra product should be used only in a humane
manner to train and educate your dog. Dogtra products
are not intended for use in any other manner nor are they
intended for use with other animals or with humans.
BATTERY
Your Dogtra product contains batteries. Take care when
removing and installing batteries as your fingers may get
caught. Dispose of batteries as provided by your local
regulations. Do not disassemble, crush, heat, or otherwise
alter the battery as it may cause fire, injury or property
damage.

4
CONTENTS
AT A GLANCE ..................................................................
MAIN FEATURES ............................................................
OVERVIEW ......................................................................
UNDERSTANDING YOUR TRAINING SYSTEM
TURNING THE EDGE RT ON/OFF .......................
TRANSMITTER BUTTON FUNCTION ..................
USING THE DOG SELECTOR DIAL .....................
RECEIVER FITTING .................................................
FINDING THE RIGHT STIMULATION ..................
MAXIMIZING THE DISTANCE ................................
LED INDICATOR .......................................................
CHARGING THE BATTERY ....................................
CHANGING THE CONTACT POINT LENGTH ....
CODE SETTING ........................................................
ATTACHING THE BELT CLIP .................................
USING THE TEST LIGHT .........................................
GENERAL TRAINING TIPS ...........................................
MAINTENANCE ...............................................................
TROUBLESHOOTING GUIDE .......................................
WARRANTY AND REPAIR INFORMATION ..............
5
6
7
9
10
12
12
13
14
15
16
17
19
20
21
22
24
25
27
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.

5
Optional Accessories
Auto Charger
Dogtra’s auto chargers are designed for use with a 10-volt
car outlet.
European Charger
Dogtra’s European chargers are designed for use with a
230V AC electrical outlet.
To purchase accessories, please visit www.dogtra.com or
call customer service at [phone].
Owner's
Manual
Belt Clip Test Light
ReceiverTransmitter Battery
Charger
Splitter Cable
Contact Point
Extension Washer
& Adjustment Tool
AT A GLANCE

6
• Selector Dial for stimulation levels 1-8
• 1-mile range
• 2 different stimulation types - Nick & Constant
• Pager vibration feature
• Stimulation/Combination buttons
• Expandable to a 3-dog system
• Fully waterproof
• Enhanced contact points
• Belt clip
• 2-hour rapid charge batteries
• High stimulation output
• For dogs as small as 35 lbs.
MAIN FEATURES

7
Antenna
Dog Selector
Dial
Selector
Dial
Belt
Clip
Battery Cover
Medium
Nick Stimulation
(Black)
Low Nick
Stimulation
(Black)
Low Constant
Stimulation
(Orange) Battery
Charging
Receptacle
& Rubber
Plug
Medium
Constant
Stimulation
(Orange)
High
Constant
Stimulation
(Orange)
High Nick
Stimulation
(Black)
Pager
Button
(Gray)
On/Off
Magnetic Red
Dot
OVERVIEW
EDGE RT
Transmitter

8
Contact
Points
Collar
Strap
LED
Indicator
Light
On/Off
Magnetic
Red Dot
Battery
Charging
Receptacle &
Rubber Plug
EDGE RT
Receiver

9
1. Turning the EDGE RT On/Off
To turn the receiver on, place the red dot on the back of
the handheld transmitter to the red dot on the receiver.
Hold the two red dots together for a moment until the
LED light on the receiver comes on.
To turn the receiver off, repeat the same procedure
holding the two red dots together momentarily. The LED
light will turn red for a brief moment indicating that the
receiver is now off.
The transmitter does not have an on/off button and it will
only activate when the buttons are pressed.
UNDERSTANDING YOUR SYSTEM

10
2. Transmitter Button Function
The handheld transmitter uses 4 buttons to send
stimulation. The LED indicator will blink on both
the handheld transmitter and the receiver when the
stimulation buttons are pressed.
1) Constant Stimulation
The two orange buttons on the front of the transmitter
control 3 levels of Constant stimulation. Pressing the
Constant button gives continuous stimulation as long as
the button is pressed, for up to 12 seconds. If the button
is not released after 12 seconds, the stimulation will
automatically turn off as a safety feature. The receiver
will be ready to be reactivated once the button has been
released.
- Low Constant Stimulation: Press the lower orange
button for a low power Constant stimulation.
- Medium Constant Stimulation: Press the top orange
button for a medium power Constant stimulation.
- High Constant Stimulation: Press both orange buttons
together for a high power Constant stimulation.
Low Constant
Stimulation
Low Nick Stimulation
High Constant Stimulation
High Nick Stimulation
Medium Constant
Stimulation
Medium Nick
Stimulation

11
2) Nick Stimulation
The two black buttons on the front of the transmitter
control 3 levels of Nick stimulation. When the Nick button
is pressed, the receiver emits a single rapid pulse of
electrical stimulation.
- Low Nick Stimulation: Press the lower black button for
Low a low power Nick stimulation.
- Medium Nick Stimulation: Press the top black button for
a medium power Nick stimulation.
- High Nick Stimulation: Press both black buttons
together for a high power Nick stimulation.
3) Pager Button
The Pager button is located on the back of the transmitter.
Pressing it will give a vibration for as long as the button is
pressed, for up to 12 seconds.

12
4. Receiver Fitting
Proper Fit
The receiver should be fitted so that the surgical stainless
steel contact points press firmly against the dog’s skin.
You should be able to fit two fingers underneath the
collar strap. The best location is on either side of the dog’s
windpipe.
Improper Fit
A loose fit can allow the receiver to move around on the
dog’s neck. When this happens, the contact points may
rub against the skin and cause irritation. If the receiver
is too loose, the contact will not be consistent and cause
the corrections to be inconsistent. Dogtra uses surgical
stainless steel contact points and anti-microbial plastic to
protect the dog’s skin.
Change the dial to select the number of the receiver that
you would like to control from the transmitter.
3. Using the Dog Selector Dial
The EDGE RT is expandable to a 3-dog system.

13
5. Finding the Right Stimulation
The EDGE RT has a Selector Dial on the top of the
transmitter (1 is the lowest and 8 is the highest).
Remember that you will need to adjust the setting (upward
or downward) depending on your dog's temperament and
threshold for stimulation. Always start at the lowest level
and work your way up. The appropriate level can be found
when the dog responds to the stimulation with a mild
reaction. Also, as the dog's attitude changes, especially
during times of increased excitement or distraction, you
may need to adjust the intensity level.
NOTE: The stimulation intensity can be adjusted even
while the stimulation is in use.
Attention!
Leaving the receiver in the same location on the dog’s
neck for an extended period of time can cause skin
irritation. If the dog is to wear the receiver for long
periods, occasionally reposition the receiver so that the
contact points are moved to a different location on the
dog’s neck. Make sure you check for skin irritation each
time you use the unit.

14
6. Maximizing the Distance
Depending on the way you use your transmitter, the
transmitter range may vary.
To get the greatest range, hold the transmitter away from
your body and avoid touching the antenna. Keep your unit
properly charged for maximum signal strength.
Typical range
Maximum range Minimum range

15
7. LED Indicator
The LED indicator flashes every 4 seconds when the
receiver is on and ready for use. The LED indicator will
blink on both the transmitter and the receiver when the
transmitter buttons are pressed.
The LED indicator color indicates the battery life level.
Green = Full charge
Amber = Medium charge
Red = Needs charge
If the unit is used while the LED indicator is red, it may
shut down automatically.

16
8. Charging the Battery
The Dogtra EDGE RT uses a lithium polymer battery.
Recharge the unit if the indicator light is red or does not
come on, the transmitter LCD shows only 1 bar on the
indicator, or the system will not stay on when any button
is pressed.
NOTE 1: Only use Dogtra-approved batteries, chargers,
and accessories for your Dogtra e-collars. This will prevent
any damage that can be incurred from attempting to use a
different charger.
NOTE 2: The unit has a partial charge when it leaves the
Dogtra facility. Upon receipt of the system, be sure to give
it a full 2-hour initial charge before the first use away from
any flammable substances.
NOTE 3: When a charger is not in use, disconnect it from
the power source. Fully charge the batteries if the unit is
to be stored without use for a period of 3 months or more.

17
Follow the steps below to charge your system:
1. Open the rubber plugs on the battery charging
receptacles and plug in the charging cable.
2. Plug the charger into a 120-volt wall outlet or, if using
the auto charger, plug into a cigarette lighter only for
lithium polymer batteries (use a 220 volt European
charger for Europe). All indicator lights should glow red
when properly plugged in and the unit will automatically
shut off during the charging process. You will need to
turn the unit on again before use once the unit is fully
charged and unplugged from the battery cable.
3. The lithium polymer battery is fully charged within
2 hours. The lights will stay red during the charging
process and turn green once the unit is fully charged.
4. After charging, cover the battery charging receptacles
with the rubber plugs.
9. Changing the Contact Point Length
The Dogtra EDGE RT comes equipped with standard 5/8”
contact points that can be extended to 3/4” contact points
to use on dogs with longer coats.
To increase the contact point length from 5/8” to 3/4”,
follow the steps below.
1. Using the included adjustment tool with the side marked
5/8”, unscrew the contact points counter-clockwise.
2. Place the contact point extension over the exposed
threads, flat side down.
3. Place the contact points over the extensions and tighten
the contact points and extensions clockwise using the
adjustment tool with the side marked 3/4”.

18
* Caution: Tighten until firmly in place. Be careful not to
over tighten.
To shorten the contact points back to the standard 5/8”,
start with the adjustment tool with the side marked 3/4”,
remove the contact point extensions, and tighten the
contact points with the adjustment tool with the side
marked 5/8”.

19
10. Code Setting
Follow the steps below to code an EDGE RT transmitter to
a new or existing receiver.
1. Set the Selector Dial to level 1
and set the Dog Selector Dial
to the number you want to
code the receiver to.
2. With the receiver turned off,
place the red dot on the back
of the transmitter to the red
dot on the receiver. Hold the
two red dots together for
about 5 seconds until the
green LED blinks rapidly on the
receiver.
3. While the green LED is rapidly
blinking on the receiver,
separate the two devices and
press the top orange button
on the front of the transmitter
and the Pager button on
the back of the transmitter
simultaneously. The LED light
on the receiver will blink every
4 seconds when coding is
complete.

20
11. Attaching the Belt Clip
Follow the instructions below to attach the included belt
clip to the transmitter.
1. Align the belt clip to the grooves on the back of the
transmitter.
2. With a firm grip, screw on the belt clip's Phillips head
screws with a screwdriver.
Caution!
Tighten until firmly in place. Be careful not to over
tighten.