Dometic DTD01A User manual

EN
DE
FR
ES
NL
IT
FI
SV
DA
NO
Tank Discharge Control
with Seacock Monitor
Instruction manual
Tankentsorgungssteuerung
with Seacock Relay
Einbauanleitung.................... 13
Commande d'évacuation du réservoir
with Seacock Relay
Mode d'emploi .....................19
Control de descarga del depósito
with Seacock Relay
Manual de instrucciones..............26
Tank-afvoerregeling
with Seacock Relay
Gebruiksaanwijzing..................33
Comando di scarico del serbatoio
with Seacock Relay
Manuale di istruzioni .................39
Säiliön tyhjennysohjaus
with Seacock Relay
Ohjekirja...........................45
Styrning för tanktömning
with Seacock Relay
Bruksanvisning .....................51
Tankudledningsstyring
with Seacock Relay
Instruktionsvejledning ................57
Styreanordning for tømming av tank
with Seacock Relay
Brukerhåndbok .....................63
DTD02A
DTD01A/02A
Tank Discharge
Control
with Seacock Monitor

2
Dometic Tank Discharge Control
1
2
4
5
3
1
3
2
A
B
CD
1
2
3
4
5
6

3
A
A
B
B
C
C
4
5
Dometic Tank Discharge Control
DTD02A
DTD01A
1
1

4
Dometic Tank Discharge Control
6

5
7A
C
H
G
F
B D E
Dometic Tank Discharge Control Installation template

6
Dometic Tank Discharge ControlInstallation template

7
EN
Table of contents
1 Notes on using the manual .................................................7
2 General safety instructions .................................................7
3 Intended use .........................................................7 - 8
4 Specications ........................................................8 - 9
5 Components ............................................................9
6 Installation ..........................................................9 - 10
7 Operation..............................................................11
8 Warranty ..........................................................12 - 13
9 Customer service........................................................13
Dometic Tank Discharge Control Notes on using the manual
1 Notes on using the manual
Caution!
Safety Instruction: Failure to observe this instruction can cause material damage and impair
the function of the device.
Note
Supplementary information for operating the device.
g. 12, page 2 : This refers to an element in an illustration. In this example, item 2 in gure
1 on page 2.
2 General safety instructions
The manufacturer will not be held liable for claims for damage resulting from the following:
• Faulty installation or connection
• Damage to the unit from mechanical inuences, misuse or abuse
• Alterations to the unit without express written permission from the manufacturer
• Use for purposes other than those described in this manual
3 Intended use
3.1 Model DTD01A discharge control (g. 4, page 3)
DTD01A Tank Discharge Control panel provides a key-operated switch to activate a discharge pump.
When the key is in the automatic power position and the panel is used with a Dometic DTM04 Tank
Monitor System, the discharge control panel activates the discharge pump automatically. The DTD
control panel can be used with virtually any electric discharge pump that operates on the same rated
voltage (12 V DC or 24 V DC) and a maximum circuit breaker or fuse rating of 20 amps.
3.2 Model DTD02A discharge control with seacock interlock monitor
(g. 5, page 3)
When integrated with the Dometic DTM04 Tank Monitor System, the DTD02A Tank Discharge Control
panel automatically activates and shuts off the discharge pump in the same manner as described for the
DTD01A panel.

8
Dometic Tank Discharge ControlIntended use
Because attempting to pump-out a holding tank can be harmful if the seacock to the overboard
discharge tting is closed, the DTD02A panel also includes a yellow warning light that indicates
when the seacock is closed. The DTD02A panel connects to two Dometic seacock switches
(available separately):
• 385310675 - seacock interlock switch and relay for Conbraco 7014701
• 385310705 - seacock interlock switch and relay for Groco BV1500
Caution!
Operator must know local regulations for emptying a holding tank.
Note
The US Coast Guard allows a key-operated switch as a means to secure an overboard
discharge pump system. Turn off DTD system and remove key from switch when boating in
“No Discharge” waters.
3.3 Features
Secure discharge pump control. Key-operated switch provides convenient means to secure
discharge pump operation without use of padlocks or other mechanical fasteners.
Helps prevent pump burn-out. Activated panel light indicates when discharge pump is operating.
Reminds operator to shut off pump when tank discharge is complete.
Prevents potential damage (DTD02A system). Activating a discharge pump while seacock is
closed can cause pressure build-up in discharge hose which may damage pump or boat and result
in costly repairs.The seacock interlock switch (available separately) greatly reduces this possibility.
Automatic discharge pump operation with DTM04 tank monitor system. Discharge pump begins
when “mid” level oat is activated, and turns off when tank level drops below “low/empty” level
probe (g. 5, page 3).
Simplifies plumbing system. Eliminates wye valves and vented loops of multi-toilet systems.
4 Specifications
4.1 Materials
Panel frame and mounting frame: ABS Circuit assembly housing: High-density polyethylene
Panel surface: Polycarbonate resin
4.2 Electrical current draw (panel only)
System Voltage Pump Off (amp) Pump On (amp)
12 V DC 0 0.16
24 V DC 0 0.095
Specications subject to change without notice. Maximum relay rating for 12 or 24 V DC discharge pump: 20 amps.
Float Switch Rating: 20 watts with resistive load (when used with DTM04 system).

9
4.3 Dimensions (g. 3, page 2)
Ref. Dimension
A 3.25 in. / 83 mm
B 3.25 in. / 83 mm
Ref. Dimension
C 51 mm / 2 in. clearance behind wall
D 0.38 in. / 10 mm
4.4 Approvals
ISO 8846; EMC Directive 2004/108/EC; CE approved for electromagnetic compatibility
5 Components (g. 1, page 2)
Ref Description Item Number (North America / Europe)
1 Replacement key 385311036 / 860003853110362
2 Switch assembly 385311610 / 860003853116104
3
DTD01A panel cover, black
DTD01A panel cover, white
DTD02A panel cover, black
DTD02A panel cover, white
385311678 / 860003853116781
385311679 / 860003853116799
385311682 / 860003853116823
385311683 / 860003853116831
4 #6 fastener 385311612 / 860003853116120
5 Mounting frame 385311613 / 860003853116138
6
DTD01A circuit ass’y, 12 V DC
DTD01A circuit ass’y, 24 V DC
DTD02A circuit ass’y, 12 V DC
DTD02A circuit ass’y, 24 V DC
(includes item 5)
385311680 / 860003853116807
385311681 / 860003853116815
385311684 / 860003853116849
385311685 / 860003853116856
6 Installation
6.1 Tank discharge control panel (g. 2, page 2)
DTD Panel Template
Dimensions (g. 7, page 5)
Ref. Dimension
A 3.25 in. / 83 mm
B 3.25 in. / 83 mm
C 2.63 in. / 67 mm
D 2.63 in. / 67 mm
E 2.16 in. / 55 mm
F 2.69 in. / 68 mm
G 0.10 in. / 2 mm dia.
H Cut-out area.
Allow 2 in. / 51 mm
clearance behind wall.
Caution!
Do not install DTD panel in an area with potentially
ammable or explosive vapors.
1. Select panel location away from direct contact with water
and oil.
2. Conrm clearance for wire connections behind wall, hull
liner or bulkhead.
3. Using control panel template (g. 7, page 5), cut out
panel access hole (E, F) and drill fastener holes (G).
4. With electrical power off, route wire from power source,
through circuit breaker or fuse (not provided), to panel
location. Route additional wires from discharge pump,
seacock relay and tank probes according to diagram (g.
6, page 4), depending on your application, to panel loca-
tion (see Section 6.2, wiring diagram key). Make sure wires
extend through panel access hole.
Dometic Tank Discharge Control Specifications

10
Dometic Tank Discharge ControlInstallation
5. Make proper wiring connections to wires extending from bottom of circuit assembly (g. 24,
page 2).
6. Remove panel cover (g. 21, page 2) from mounting frame (2) by carefully pulling them apart.
Make sure wires between key switch (3) and circuit assembly (4) remain attached. (Key pin 1 –
red; pin 2 – brown; pin 7 – blue; pin 8 – red.)
7. Install mounting frame to wall with four fasteners (5).
8. Tuck key switch wires into circuit assembly housing, and push panel cover onto mounting frame
until it locks into place.
9. Turn on electrical power.
6.2 Key to DTD01A/02A and DTM04 system wiring (g. 6, page 4)
Ref. Description
A DTD01A or DTD02A control panel
B Discharge pump
C DTM04 indicator panel
D Wastewater tank
E 12 or 24 V DC
F V DC ground
G Discharge pump circuit breaker or fuse
H 12 V DC
I 24 V DC
J 1-amp circuit breaker or fuse
K Toilet system circuit breaker or fuse
L + V DC to electric toilet system
M Full level probe
Ref. Description
N Mid level probe
O Low/Empty level probe
P Red
Q Black
R Brown
S Green
TBlue
UYellow
VOrange
WWhite
XSeacock interlock switch
Y“Check seacock” indicator light
(DTD02A only)
1. Heavy lines in wiring diagram represent stranded copper wire to be sized according to ABYC recommendations.
2. Other wire can be 18 gauge stranded copper wire or larger.
3. Maximum discharge pump circuit breaker or fuse rating: 20 amps.

11
Dometic Tank Discharge Control Operation
7 Operation
Caution!
Operator must know local regulations for emptying a holding tank.
7.1 DTD01A discharge control with DTM04 tank monitor system (g. 4, page 3)
1. When boat is in unrestricted waters and automatic pump-out is desired, open seacock, insert
key into switch and turn to “automatic power” position (A).
2. As holding tank content level increases and raises the “mid” level oat, the discharge pump
starts (B). A green “tank discharge” light indicates when the discharge pump is operating.
3. When tank content level falls below the “low/empty” probe, the pump automatically stops
operating (C).
4. If pump-out is desired but the “mid” level oat has not activated the discharge pump, turn the
key to the “manual start” position (B 1). Hold the key until tank discharge is complete, then let
key rebound to “off” position.
Caution!
Do not allow discharge pump to operate for an extended period of time when there is no
discharge from holding tank. Damage to pump may result.
7.2 DTD02A discharge control panel with DTM04 tank monitor system
(g. 5, page 3)
1. When boat is in unrestricted waters and automatic pump-out is desired, open seacock, insert
key into switch and turn to “automatic power” position (A).
2. If seacock is closed, the interlock switch sends a signal to the panel, the yellow “caution”
indicator turns on, and the discharge pump will not start. To start discharge pump with key in
“automatic power” position, open the seacock, and pump will start (B). A green “tank discharge”
light indicates when the discharge pump is operating.
3. When tank content level falls below the “low/empty” probe, the pump automatically stops oper-
ating (C).
4. If pump-out is desired but the “mid” level oat has not activated the discharge pump, turn the
key to the “manual start” position (B 1). Hold the key until tank discharge is complete, then let
key rebound to “off” position.

12
Dometic Tank Discharge ControlWarranty and Product Liability
8 Warranty and product liability
North America:
Manufacturer’s One-Year Limited Warranty
Dometic Corporation, Sanitation Division (Dometic) warrants to the original purchaser only that this
product, if used for personal, family or household purposes, is free from defects in material and
workmanship for a period of one year from the date of purchase.
If this Dometic product is placed in commercial or business use, it will be warranted to the original
purchaser only to be free of defects in material and workmanship for a period of ninety (90) days
from the date of purchase.
Dometic reserves the right to replace or repair any part of this product that proves, upon inspection
by Dometic, to be defective in material or workmanship. All labor and transportation costs or
charges incidental to warranty service are to be borne by the purchaser-user.
EXCLUSIONS
IN NO EVENT SHALL DOMETIC BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES,
FOR DAMAGES RESULTING FROM IMPROPER INSTALLATION, OR FOR DAMAGES CAUSED
BY NEGLECT, ABUSE, ALTERATION OR USE OF UNAUTHORIZED COMPONENTS. ALL IMPLIED
WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR
ANY PARTICULAR PURPOSE, ARE LIMITED TO A PERIOD OF ONE YEAR FROM DATE OF
PURCHASE.
IMPLIED WARRANTIES
No person is authorized to change, add to, or create any warranty or obligation other than that set
forth herein. Implied warranties, including those of merchantability and tness for a particular
purpose, are limited to one (1) year from the date of purchase for products used for personal, family
or household purposes, and ninety (90) days from the date of purchase for products placed in
commercial or business use.
OTHER RIGHTS
Some states do not allow limitations on the duration of an implied warranty and some states do not
allow exclusions or limitations regarding incidental or consequential damages; so, the above limita-
tions may not apply to you. This warranty gives you specic legal rights, and you may have other
rights which vary from state to state.
To obtain warranty service, rst contact your local dealer from whom you purchased this product or
go to http://www.dometic.com for a dealer near you.

13
Dometic Tank Discharge Control Warranty and Product Liability
Europe:
Warranty and Customer Service
Warranty arrangements are in accordance with EC Directive 44/1999/CE and the normal conditions
applicable for the country concerned. For warranty or other service, please contact our Dometic
Service department listed elsewhere in this manual. Any damage due to improper use is not covered
by the warranty.
The warranty does not cover any modications to the product or the use of non-original Dometic
parts; the warranty does not apply if the installation and operating instructions are not adhered to
and no liability shall be entertained.
Product Liability
Product liability of Dometic Group and its subsidiary companies does not include damages which
may arise from: faulty operation; improper alterations or intervention in the equipment; adverse
effects from the environment which may impact the equipment itself or the direct vicinity of the
equipment or persons in the area.
To obtain warranty service, rst contact your local dealer from whom you purchased this product or
go to http://www.dometic.com for a dealer near you.
9 Customer service
There is a strong, worldwide network to assist in servicing and maintaining your toilet system. For
the Authorized Service Center near you, please call from 8:00 a.m. to 5:00 p.m. (ET)
Monday through Friday.
You may also contact or have your local dealer contact the Parts Distributor nearest you for quick
response to your replacement parts needs. They carry a complete inventory for the Dometic product
line.
Telephone: [phone] U.S.A. and Canada
330-439-5550 International
Fax: [phone] U.S.A. and Canada
330-439-5567 International
Web sites: http://www.Dometic.com
http://www.DometicSanitation.com

14
Dometic Tank Discharge ControlNotes

15
Dometic Tank Discharge Control Notes

Dometic Tank Discharge Control
Dometic is a customer-driven, world-leading provider
of leisure products for the RV, automotive, truck
and marine markets. We supply the industry and
aftermarket with a complete range of air conditioners,
refrigerators, awnings, cookers, sanitation systems,
lighting, mobile power equipment, comfort and safety
solutions, windows, doors and other equipment that
make life more comfortable away from home.
Dometic supplies a wide range of workshop
equipment for service and maintenance of built-in
air conditioners. Dometic also provides specially
designed refrigerators for hotel rooms, ofces,
wine storage and transport and storage of medical
products.
Our products are sold in almost 100 countries and are
produced mainly in wholly-owned production facilities
around the world.
Dometic Corporation, Sanitation Division
13128 State Rt. 226, P.O. Box 38
Big Prairie, OH 44611 USA
1-800-321-9886 • Fax: [phone]
www.Dometic.com
REVISION A
Form No. 600346276 8/17
©2017 Dometic Corporation