Dometic Saneo B User manual

MBA 03/2015
N 1
Installation Instructions
Cassette toilet for recreational vehicles
10 R - 047317
Saneo B
®
Dometic
Saneo C
®
Dometic
Saneo BS
®
Dometic
Saneo CS
®
Dometic
Saneo BW
®
Dometic
Saneo CW
®
Dometic
Saneo BLP
®
Dometic
Saneo CLP
®
Dometic
EN
English
More information https://www.caravansplus.com.au

2
For your safety
Saneo B
Saneo C
Saneo BS
Saneo CS
Saneo BW
Saneo CW
Saneo BLP
Saneo CLP
©Dometic GmbH - 2015 - Subject to change without prior notice
Dometic GmbH
In der Steinwiese 16
D-57074 Siegen
www.dometic.com
CAUTION!
The toilet must be installed by trained
staff only.
Cleaning agents for the toilet must not
contain chlorine or alcohol!
Do not shake the cassette tank violently.
All components of the system must be
installed in frost-protected areas. In minus
temperatures there is a risk of damage
due to frost.
Do not use anti-freeze agents. Such
agents can damage the sanitation system.
The operating pressure range (waterpres-
sure) of the magnet valve must not exceed
6 bar. The magnet valve will be damaged
by excessive pressure.
CAUTION!
More information https://www.caravansplus.com.au

1.0 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.1 Guide to these operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
1.2 Copyright protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.3 Explanation of symbols used in this manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.4 Limitation of liability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.5 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.6 Environmental notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.7 Declaration of conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.0 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.1 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.2 Installation notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.3 Standards and regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.0 Description of model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.1 Model identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.2 Toilet identification label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.3 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.4 Explanation of components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4.0 Installation of toilet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.1 Installing the service door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.2 Create wall apertures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.2.1 Wall aperture service door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.2.2 Wall aperture flap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.3 Installing the toilet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.3.1 Placing the Saneo B, Saneo C toilet models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.3.1.1 Fitting the Saneo B, Saneo C toilet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.3.1.2 Installing the control and operator panel of the Saneo B, Saneo C toilet . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.3.2 Placing the Saneo BW, Saneo CW, Saneo BS, Saneo CS, Saneo BLP, Saneo CLP toilet models . . . . . 10
4.3.2.1 Fitting the wall holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.3.2.2 Fitting the Saneo BW, Saneo CW, Saneo BS, Saneo CS, Saneo BLP, Saneo CLP toilet . . . . . . . . . . . . . 11
4.4 Water connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.5 Flap installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.6 Electric connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.6.1 System diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.6.1.1 General system diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.6.1.2 System diagram (Saneo xW model with integrated water pump) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.6.1.3 System diagram (Saneo B, C/ Saneo xS/ Saneo xLP models with external water pump) . . . . . . . . . . . . 14
5.0 Annex . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
5.1 Circuit diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
5.1.1 Circuit diagram (models with external water tank) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
5.1.2 Circuit diagram (models with internal water tank) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-4
5.1.3 Circuit diagram (models with internal water tank, GB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-6
5.1.4 Circuit diagram (models with external water tank) AUSTRALIA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-7
5.1.5 Legend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-8
5.2 Dimensioned sketches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-13
5.3 Attaching the toilet housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-18
5.4 Templates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-24
3
Table of contents
More information https://www.caravansplus.com.au

4
1.0 General
The information, texts and illustrations in these
instructions are copyright protected and are
subject to industrial property rights. No part of
these instructions may be reproduced, copied
or utilised in any other way without written aut-
horisation by Dometic GmbH, Siegen.
1.2 Copyright protection
Before installing the toilet read and under-
stand the contents of this manual.
These instructions provide you with the neces-
sary guidance for the proper installation of the
toilet. Observe the safety instructions in
particular. Observing the instructions and
handling recommendations is important for
dealing with the toilet safely and for protecting
you from injury and the toilet from damage.
You must understand what you have read
before you carry out a task.
1.1 Guide to these installation
instructions
General
CAUTION!
CAUTION!
Information
i
1.3 Explanation of symbols
used in this manual
Warning notices are identified by symbols. A
supplementary text gives you an explanation
of the degree of danger.
Observe these warning notices rigorously.
You will thus protect yourself and other
people from injury, and the sanitation
system from damage.
Warning notices
CAUTION indicates a potentially hazardous
situation which may result in minor or modera-
te injury if the given instructions are not adher-
ed to.
Environmental tip
Environmental tip gives you useful guidance
for saving energy and disposal of the appliance.
CAUTION (used without the safety alert sym-
bol) indicates a potentially hazardous situation
which may result in damage to the appliance if
the given instructions are not adhered to.
INFORMATION gives you supplementary and
useful guidance.
More information https://www.caravansplus.com.au

5
General
In order to ensure that the recyclable packa-
ging materials are re-used, they should be
sent to the customary local collection system
Disposal
Dometic products meet the specified features
in accordance with the relevant European
standards.
The current Declaration of Conformity can be
requested directly from Dometic GmbH,
Siegen.
Warranty arrangements are in accordance
with EC Directive 44/1999/CE and the normal
conditions applicable for the country concer-
ned. For warranty or other maintenance, plea-
se contact our customer services department.
Any malfunction due to improper use is not
covered by the warranty. The warranty does
not cover any modifications to the appliance
or the use of non-original Dometic parts.
The warranty does not apply if the installation
and operating instructions are not adhered to
and no liability shall be entertained.
1.5 Warranty
All information and guidance in these opera-
ting instructions were prepared after taking
into consideration the applicable standards
and regulations as well as the current state of
the art. Dometic reserves the right to make
changes at any time which are deemed to be
in the interest of improving the product and
safety.
Dometic will assume no liability for damage in
the case of :
!non-observation of the installation instructi-
ons
!non-observation of the operating instructi-
ons
!application not in accordance with the
regulations or provisions
!use of non-original spare parts
!modifications and interferences to the
appliance
1.4 Limitation of liability 1.6 Environmental notices
1.7 Declaration of conformity
More information https://www.caravansplus.com.au

6
2.0 Safety instructions
This toilet is designed for installation in recrea-
tion vehicles such as caravans or motorho-
mes.
2.1 Intended use
Safety instructions / Description of model
The toilet must be in principle installed so that
it is accessible for maintenance work, can be
easily installed and dismantled and removed
from the vehicle without great effort.
2.2 Installation notes
Installation and connection of the sanitation
system must comply with the latest technical
regulations, as follows:
!The electrical installation must comply
with national and local regulations.
!European standards
EN 1645-1, EN 1646-1,EN 1648-1 ,
EN 1648-2
2.3 Standards and regulations
The toilet must be installed by trained staff
only.
CAUTION!
3.0 Description of model
3.1 Model identification
The Saneo cassette toilet consists of a toilet
which is installed fixed in the vehicle and a
removable, mobile cassette as a faeces tank.
The cassette can be accessed from the outsi-
de through a door. Depending on the model,
the toilet receives the flush water from a tank
integrated in the model or from a fresh water
tank installed in the vehicle.
The following models are available:
!Saneo B, Saneo C : free-standing, without
water tank, without console
!Saneo BS, Saneo CS : free-standing,
without water tank, with console
!Saneo BW, Saneo CW : free-standing, with
water tank in console
!Saneo BLP, Saneo CLP : free-standing,
without water tank, with low profile console
S = free-standing without
flush water tank,with
console
W = free-standing with
integrated flush
water tank
LP = Low Profile, low con-
sole
Model range
Model version
B = Basic with plastic bowl
C = Comfort with ceramic bowl
Example:
Saneo B L P
More information https://www.caravansplus.com.au

7
Description of model
1 = Removable cover and seat
2 = Toilet bowl made of plastic or ceramic
3 = Emptying blade for the toilet bowl
4 = Console for water tank
5 = Level indicator / control panel (flush)
6 = Flap / fresh water filler plug
7 = Service door
2
4
3
1
3.4 Explanation of components
Fig. 2
08 = Cassette tank
09 = Pour out spout
10 = Vent button for emptying
Fig. 3
5
3
10
9
8
6
7
The identification label contains all important
details. You can read off from this the model
identification, the product number and the
serial number. You will need these details whe-
never you contact the customer services cen-
tre or when ordering spare parts. You will find
the identification label within the cassette hou-
sing after removing the cassette.
3.2 Toilet identification label
Supply voltage : 12 V DC
Current consumption : max. 2 A with internal
water pump, max. 10 A with external pump.
Dimensions : s. details in appendix
Operating temperature : 0°C up to + 50°C
Capacity: :
Cassette tank ..........................16l
Fresh water tank (optional) ....... 7l
3.3 Technical data
Required pump output at the inlet of the toi-
let: min. 5.5 l/min, max. 12 l/min (recom-
mended 7-8 l/min).
i
Fig.1
Example
1
2
3
Model number
Product number
Serial number
2
1
3
More information https://www.caravansplus.com.au

8
Installation of toilet
4.0 Installation of toilet
4.2 Create wall apertures
4.1 Installing the service door
The description for the installation of the ser-
vice door can be found in the document sup-
plied Dometic Seitz SK 5 ) (optional/depen-
ding on model).
4.3 Installing the toilet
When installing the toilet in a wet room, we
recommend connecting the toilet with the
shower tub.
!Install the toilet according to the descripti-
on of the respective model.
!Only install the toilet against an upright
wall.
!Leave at least 60 mm clearance from side
walls so that swivelling of the toilet top part
(with seat) is not restricted.
!Observe the dimension sketches and
templates, section 5.2, 5.3., 5.4 .
4.2.1 Wall aperture service door
The flap is applied when using Saneo BW and
Saneo CW models with an integrated water
tank. Use the template (1) , Item 5.3.1., to
make the aperture for the flap. You can find the
installation instructions for the flap under Item
4.5.
4.2.2 Wall aperture flap
All components of the system must be
installed in frost-protected areas. In
minus temperatures there is a risk of
damage due to frost.
CAUTION!
Fig. 6
Make an aperture in the wall for the cassette
with the following dimensions:
for service door SK5 vertical
ymin = 12.5 mm, ymax = 22 mm;
b = 310 mm +/- 1 mm, h = 360 mm +/- 1 mm.
for service door SK5 horizontal
ymin = 12.5 mm, ymax = 26 mm;
b = 360 mm +/- 1 mm,h = 310 mm +/- 1 mm.
The x value results from the toilet installation.
Observe the position of the service door (tem-
plate (3) and (4) on packaging).
SK 5 vertical
Fig. 4
b
x
h
y
SK 5 horizontal
Abb. 5
b
h
y
x
More information https://www.caravansplus.com.au

9
Installation of toilet
The free-standing models Saneo B, Saneo C
model has no integrated water tank. Install
this model so that the wall behind it can
absorb the control panel of the toilet, the elec-
tric connections and the water tank, if applica-
ble. It is ideal to set a box in front of the room
wall, as illustrated in Fig. 7. Install the control
and operator panel in immediate proximity to
the toilet (see Section 4.3.1.2).
Note that the cassette projects 112 mm (a) out
of the cassette housing (Fig. 8).
Attach the case bottom (1) flush with the
mounting frame of the service door so that a
clean transition without gap is produced.
4.3.1 Installing the Saneo B, Saneo C
toilet
Fig. 7
Fig.9
Fig. 8
a
4.3.1.1 Fitting the Saneo B, Saneo C toilet
Once the toilet is installed in the desired posi-
tion, bolt down the floor plate with the four
screws (enclosed) (Fig. 10) .
Then attach the toilet housing (with no more
than 4 screws, not enclosed) to the wall (Fig.
11).
Fig. 10
4x
1
1
1:1 template can be requested direct-
ly from Dometic.
Fig. 11
i
More information https://www.caravansplus.com.au

10
Installation of toilet
Fig. 13
Fig. 14
Saneo BW, Saneo CW
Saneo BS, Saneo CS
4.3.1.2 Installing the control and operator
panel of the Saneo B, Saneo C toilet
Install the control and operator panel for the
Saneo B, Saneo C toilet in an easily accessi-
ble position on the wall. First cut the aperture
in the wall (Fig.12). Use true-to-scale tem-
plate (4) to make the wall aperture.
Connect the electric cables on the couplers to
install the control and operator panel (are sup-
plied separately) (s. item 4.6
Electric connecti-
on
)
In order to insert the control panel in the wall
aperture, press the holding springs (1) of the
control and operator panel back.
These models have a wall connection bracket.
The control and operating panel is integrated
in the wall connection bracket.
The Saneo BW and Saneo CW models have
an installed water tank while the Saneo BS
and Saneo CS models have no water tank.
Install all models with wall connection bracket
directly on the room wall (see following figure).
A previously installed wall holder (see section
4.3.2.1) is used for fastening of the toilet and
the bracket.).
4.3.2 Installing the Saneo BW,
Saneo CW, Saneo BS, Saneo CS,
Saneo BLP , Saneo CLP toilets
4.3.2.1 Fitting the wall holder
Fit the wall holder (1) in the designated posi-
tion (see table and Fig. 16).
Fig. 15
Saneo BLP, Saneo CLP
Detail screw
1
1
1
There is a risk of injury from springs jum-
ping back!
CAUTION!
Fig. 12
135 mm +/- 0.1mm
R 10
88 mm + 0.2 mm
More information https://www.caravansplus.com.au

11
Installation of toilet
Fig. 18
Fig. 16
a
b
Fitting height of the wall holder :
Model a b
Saneo BW / Saneo BS
Saneo CW / Saneo CS 90 mm 644.0 mm
Saneo BLP
Saneo CLP 90 mm 461.0 mm
Fig. 17
Place the entire toilet module in the desired
position in front of the wall holder. Lift the toi-
let. Then place the toilet so that the part on the
side of the wall of the housing hooks into the
the wall holder (Fig. 17).
4.3.2.2 Fitting the Saneo BW,
Saneo CW, Saneo BS, SaneoCS,
Saneo BLP , Saneo CLP toilets
Detail wall holder
Fig. 18
2
1
1 = Wall holder
2 = Wall connection console
1
2
11
If the toilet is installed in the desired position,
bolt down the floor plate with the four screws
enclosed and insert the mobile tank cassette.
Fastening screws (3) and caps (4) are supplied
with the toilet.
Fig. 20
Fig. 19
4x
4
3
More information https://www.caravansplus.com.au

12
Installation of toilet
4.4 Water connection
Then check the leak tightness.
4.5 Flap installation
Apply the flap when using Saneo BW and
Saneo CW models with an integrated water
tank. To install the flap, use the template (1) ,
Item 5.3.1, in order to make the aperture in the
wall.
Fig. 22
position of O-rings with wall
thickness of 30mm -50mm
position of O-rings with wall
thickness of 20,5mm -30mm
Apply sealing compound between the exterior
wall of the vehicle and the flap (butyl rubber).
Then fit the flap on the tank and fasten the flap
with screws. Lubricate the O-ring in order to
prevent stiffness when connecting the filling
nozzle with the top of the tank. The flap is
screwed on with four counter sunk bolts
(C4x25) (not enclosed).
The water is connected for all CT4xxx models
as described above.
Exception : Saneo
x W models with integra-
ted water tank.
The operating pressure range (waterpres-
sure) of the magnet valve must not exceed
6 bar.
The magnet valve will be damaged by
excessive pressure.
CAUTION!
Required pump output at the inlet of the toi-
let: min. 5.5 l/min, max. 12 l/min (recom-
mended 7-8 l/min).
i
The water supply is connected using a smooth
tube connection (1).
The connection sleeve is not included in the
scope of delivery.
Fig. 21
1
More information https://www.caravansplus.com.au

13
Installation of toilet
Fig. 24
Fig. 23
4.6 Electric connection
4.6.1 System diagrams
Electric connection must be carried out
by trained staff.
CAUTION!
Note the following instructions before installa-
tion of the cassette toilet:
!Connect the toilet to a suitable power
supply via the main connection block of
the vehicle (Fig. 23).
!The toilet must not be directly connected
in parallel to other consumers, otherwise
malfunctions or damage to the toilet
controller can occur (Fig. 24).
!A line fuse is not necessary as the toilet
is fused internally.
12 V DC
Battery
Fuse / main connection box
Toilet
Saneo
Water pump
Do NOT connect for use of a
pressurised water pump!
Toilet
Saneo
Water pump
12 V DC
Do not connect toilet to the power supply
directly in parallel with other electrical
consumers.
CAUTION!
+
-
+
-
+
-
+
-
Please find circuit diagrams in Chapt. 5,
annex !
i
4.6.1.1 General system diagram
More information https://www.caravansplus.com.au

14
Installation of toilet
Fig. 25
4.6.1.2 System diagram (Saneo x W model with integrated water pump)
Supply voltage : 12 V DC
12V connection cable profile :
min. 0.75 mm²
Toilet control fuse : 10A
(integrated automobile fuse)
Current consumption of the pump : max. 2A
Control and operator panel
4.6.1.3 System diagram (Saneo B, C/ Saneo xS/ Saneo xLP models with external
water pump)
Supply voltage : 12 V DC
12V connection cable profile :
min. 1.5 mm²
Toilet control fuse : 10 A
(integrated automobile fuse)
Current consumption of the pump :
max. 8 A
The external water pump is not included in the
scope of delivery.
The external water pump must not exceed
a nominal power of 100 W.
CAUTION!
Fig. 26
Control and operator panel
i
Connection 12V- supply
Connection magnetic valve
2
1
2
1
Connection 12V- supply
Connection magnetic valve
Connection external pump
2
1
3
2
1
3
More information https://www.caravansplus.com.au