DOT Compact User manual

PLEASE READ THE ENTIRE OWNER’S MANUAL BEFORE USING YOUR DOT BOARD
OWNER’S MANUAL
THE WORLDS MOST ADVANCED
ELECTRIC SKATEBOARD

2
INDEX
SAFETY .........................................4
UNBOXING YOUR dot BOARD...................5-6
ACCESSORIES AND MODIFICATIONS...............7
dot TRANSPORTER ...............................8
dot CRUISER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
dot COMPACT..................................10
dot REMOTE....................................11
dot BATTERY MODULE ..........................12
dot MAIN CONTROLLER.........................13
BATTERY SAFETY ...............................14
BATTERY INFORMATION .....................15-17
BATTERY INSTALLCHARGING THE BATTERIES ......18
CHARGING THE REMOTE .......................19
PAIRING THE REMOTE ...........................20
REMOTE FEATURES .............................21
REMOTE MENU NAVIGATION .................22-25
REMOTE MENU DETAILS .........................26
CHANGING RIDE LEVELS ........................27
REMOTE WARNINGS .........................28-29
GETTING READY TO RIDE........................30
OPERATING YOUR dot BOARD ...................31
MOTOR INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . .32
INSTALLING 120MM WHEELS .....................33
FIRMWARE UPDATES ............................34
STORING YOUR dot BOARD ......................35
AIR TRAVEL ....................................36
LIMITED WARRANTY ............................37
CERTIFICATIONS ............................38-39
REGULATIONS .................................40
DISPOSAL INFORMATION........................41

3
WARNINGS
DO NOT USE THIS PRODUCT UNTIL YOU READ THE ENTIRE MANUAL,WHICH EXPLAINS
HOW TO REDUCE SOME RISKS.
THE USE OF ANY SKATEBOARD PRESENTS RISKS AND DANGERS. THE USE OF THIS PRODUCT
HAS INHERENT RISKS AND DANGERS AND ITS USE CAN RESULT IN SERIOUS INJURY OR
DEATH EVEN WHEN SAFETY EQUIPMENT IS USED AND OTHER PRECAUTIONS ARE TAKEN.
THIS PRODUCT INCLUDES ONE OR MORE RECHARGEABLE BATTERIES WHICH POWERS ONE
OR MORE ELECTRIC MOTORS. MISUSE OF THE BATTERY CAN RESULT IN SERIOUS INJURY,
DEATH, FIRE OR OTHER DAMAGE. READ AND FOLLOW THE SEPARATE WARNINGS AND
INSTRUCTIONS REGARDING THE BATTERY.
USE THIS PRODUCT AT YOUR OWN RISK.
Depending upon the age, skill level and maturity of the
user, the dot board may not be suitable for everyone.
This product is not recommended for riders under
the age of 18. The use of this product by someone
who lacks the necessary physical development, skills
or maturity presents an increased risk of serious
injury or death. This product is NOT a toy. NEVER
leave this product with unattended children.
Under some circumstances, the electric brakes may
not work, especially if the battery is fully charged due
to the regenerative braking feature. It is also possible
to lose power and brakes due to radio interference
or a dead Remote control battery.Therefore,
only ride this product at speeds, on slopes, and in
situations where you would be comfortable riding the
product without power or brakes.
Not wearing a helmet increases the chances of
serious injury or death. Be sure you always wear a
helmet and other protective gear when you ride.
Once the skateboard starts moving, the Remote
control will continue to respond to the skateboard
even if you are not on the skateboard. If you step off,
fall off the skateboard, or are not on the skateboard
while the skateboard is moving, the skateboard will
continue to move even if you are not on it. Therefore,
it is important that you use the Remote only while
you are on the skateboard or while the skateboard
is in the upside down position. In the event of a
runaway skateboard, attempt to use the brakes on the
Remote to stop the skateboard but be aware that it is
possible that the brakes may not always work.

4
WARNINGS
While your dot board is equipped with red rear
lights, they are not brake lights and may not always
be visible. If you ride in low visibility conditions, use
equipment and clothing that makes you visible to
others and that allows you to see where you are
going.
This product is not for riders heavier than 120
kilograms. Do Not Exceed The Weight Limit Of 120
Kilograms – including backpacks and other items that
the rider might be carrying.
This product is intended to be a single rider use only.
DO NOT ride with any additional passengers. Doing
so may exceed the capacity of the product and result
in a loss of control or reduced braking or insufcient
power.
Do not disassemble or tamper with or attempt to
repair the hub motor(s), or the Main Controller
Module or battery, or the Remote Control. They
contain chemicals or components that may cause
injury.
Do not touch the rear truck or motor after extended
use as they may get hot and may cause burns.
YOUR SAFETY IS UP TO YOU.
It is not possible to list all do’s and don’ts. We list
only some ways that may help reduce the risk of
injury or death:
• Wear a helmet – ALWAYS WEAR A HELMET TO REDUCE
THE RISK OF HEAD INJURIES
• Wear other protective gear and clothing
• Ride within your capabilities and use common sense and good
judgment
• Pay attention to your surroundings and watch for cars,
pedestrians, bikes, other vehicles and other hazards
• Ride on at, level ground that is clear of debris
• Never ride in wet conditions
SAFETY LABELS
Safety labels on your skateboard either warn you of
potential hazards that could cause serious injury or
provide important safety information. Read these
labels carefully and don’t remove them.
Note: If a label comes off or becomes hard to read,
contact us at [e-mail]

5
UNBOXING YOUR dot BOARD
UNBOXING YOUR dot BOARD
Your dot skateboard comes in its own specially
designed case. Inside you will nd everything you
need to get you going.
Once you remove the skateboard, you will see inside
the following items:
• Safety warning sheet, Battery Information Sheet and Quick
start Guide.
• dot board – Transport, Cruiser or Compact.
• Battery modules (up to 4, depending on your model and
conguration), which will already come installed on your dot
Board.
• Battery front deector cover and battery screws, which will
come already installed on your dot board.
• Battery terminal cover caps (Red) – these will be in your
spares bag.
• Remote controller and Remote controller charging USB cable.
• AC power adaptor (country specic) and magnetic charging
cable
• Skate tool, Dot Hex-drive tee bar, Spares parts package
Your dot board comes fully assembled in accordance with the
model and conguration that you purchased.
Remove your dot board from the case and inspect the
skateboard for any damage that may have occurred during
shipping or any missing parts. If anything is damaged or missing,
please contact customer service immediately for assistance. You
can reach customer service at [email protected]
Read and fully understand all the information in this manual, the
Safety Warning Sheet, Battery Information Sheet, and Quick Start
Guide supplied with your board and also pay particular attention
to the warning labels applied to the board, power adaptor,
charging cables and Remote.
If you have any further queries with the information provided
in this manual, Safety Warning Sheet, Battery Information Sheet,
Quick Start Guide and on warning labels, please contact
customer service via email at [e-mail]
Your dot skateboard has been transported with lithium ion
battery modules. Please, carefully examine these modules for
any signs of damage – including cracks. Contact your authorised
dealer for further instructions.

6
UNBOXING YOUR dot BOARD

7
ACCESSORIES AND MODIFICATIONS
Modifying your skateboard or using uncertied dot
board accessories can make your skateboard unsafe.
Before you consider making any modication or
adding an accessory, be sure to read the following
information.
IMPROPER ACCESSORIES OR MODIFICATIONS
CAN CAUSE A CRASH IN WHICH YOU CAN BE
SERIOUSLY HURT OR KILLED.
FOLLOW ALL INSTRUCTIONS IN THIS OWNER’S
MANUAL REGARDING ACCESSORIES AND
MODIFICATIONS.
We strongly recommend that you only use dot board
accessories that have been specically designed and
tested for your skateboard. Because dot board can-
not test all other accessories, you must be personally
responsible for the proper selection, installation and
use of uncertied dot board accessories.
Check with your dot board authorized Service Agent
for assistance and always follow these guidelines:
Make sure the accessory does not obscure any
electrical components, reduce ground clearance, limit
braking ability or steering angle, alter your riding posi-
tion or interfere with operating any controls.
Do not add any electrical equipment to the skate-
board’s electrical system. A blown fuse can cause a
loss of lights or motor power.Any interference to
the electrical system can result in erratic behaviour
of the controller. Do not modify the battery module.
Do not modify the cells contained within the battery
module, these have been specically designed, pro-
grammed and tested to ensure the best performance
from your dot board skateboards and for your safety.
We strongly advise you not to remove any original
equipment or modify your skateboard in any way that
would change its design or operation. Such changes
could seriously impair your skateboard’s handling,
stability, and braking, wwmaking it unsafe to ride.
Do not open or tamper with the electrical or
electronic housings, including battery electronics
and cells. This is dangerous and can lead to re or
explosion. Tampering will also void your warranty.
Do not use uncertied dot board batteries, chargers
or other parts with your dot board electric
skateboard. Only use genuine dot board batteries,
chargers, and parts. The use of uncertied dot board
batteries, chargers or parts with your dot board may
pose a re hazard which can result in serious injury
or death.

8
dot TRANSPORTER
Range:
Two Batteries 12 Miles
Three Batteries 18 Miles
Four Batteries 24 Miles
Max Speed:
83mm Wheels: 18 MPH
120mm Wheels: 24 MPH
Hill Climb:
up to 30% grade
Product Weight:
Two Batteries + Two Motors: 16 lbs
Three Batteries + Two Motors: 18 lbs
Four Batteries + Two Motors: 20 lbs
Dimensions:
11 inches (wide), 42 inches (length), 5 1/2 inches (height)
Peak Power:
2,100 watts
Brakes:
Regenerative braking delivered by the dot Hub Motor
Deck:
8-ply teak + hard rock maple, eco-resin construction
Wheels:
83mm 78a or 120mm 78a urethane
Front Truck:
150mm magnesium reverse kingpin
Charging:
3.5A 48V DC power adaptor with magnetic cable (standard)
Charge Time:
Two Batteries with Standard 3.5A 48V Adaptor - 90 Minutes
Three Battery with Standard 3.5A 48V Adaptor - 135 Minutes
Four Battery with Standard 3.5A 48V Adaptor - 180 Minutes
The Transporter offers a long-range, powerful,
comfortable transport solution.With a standard
conguration of two motors and two batteries - you
have the option to upgrade to three or four batteries
and larger 120mm comfort wheels.This is the long
range, go everywhere dot board for you.

9
dot CRUISER
Range:
One Battery 6 Miles
Two Batteries 12 Miles
Three Batteries 18 Miles
Max Speed:
18MPH
Hill Climb:
up to 30% grade
Product Weight:
One Battery + One Motor: 12 lbs
Two Batteries + Two Motors: 14 lbs
Three Batteries + Two Motors: 18 lbs
Dimensions:
10 inches (wide), 37 inches (length), 5 ½ inches (height)
Peak Power:
2,100 watts
Brakes:
Regenerative braking delivered by the dot Hub Motor
Deck:
6mm V-Ply + berglass, eco-resin construction
Wheels:
83mm 78a urethane
Front Truck:
150mm Magnesium reverse kingpin
Charging:
1.5A 48V DC power adaptor with magnetic cable
Upgradable to 3.5A 48V DC power adaptor as an accessory
Charge Time:
One Battery with Standard 1.5A 48V Adaptor - 60 Minutes
Two Battery with Standard 1.5A 48V Adaptor - 120 Minutes
Three Battery with Standard 1.5a 48V Adaptor - 180 Minutes
One Battery with Optional 3.5A 48V Adaptor - 45 Minutes
Two Battery with Optional 3.5A 48V Adaptor - 90 Minutes
Three Battery with Optional 3.5A 48V Adaptor - 135 Minutes
This dot model is the right mix of power, portability
and range. With a standard conguration of one
motor and one battery - you have the option to
upgrade to a two-motor conguration and upgrade to
two or three batteries.This is the best of everything
dot board for you.

10
dot COMPACT
Range:
One Battery 6 Miles
Two Batteries 12 Miles
Max Speed:
18 MPH
Hill Climb:
up to 30% grade
Product Weight:
One Battery + One Motor: 12 lbs
Two Batteries + One Motor: 14 lbs
Two Batteries + Two Motors: 16 lbs
Dimensions:
10 inches (wide), 31 inches (length), 5 ½ inches(height)
Peak Power:
2,100 Watts
Brakes:
regenerative braking delivered by the dot Hub Motor
Deck:
6mm V-Ply + berglass, eco-resin construction
Wheels:
83mm 78a urethane
Front Truck:
150mm magnesium reverse kingpin
Charging:
1.5A 48V DC power adaptor with magnetic cable
Upgradable to 3.5A 48V DC power adaptor as an accessory
Charge Time:
One Battery with Standard 1.5A 48V Adaptor - 60 Minutes
Two Batteries with Standard 1.5A 48V Adaptor - 120 Minutes
One Battery with Optional 3.5A 48V Adaptor - 45 Minutes
Two Battery with Optional 3.5A 48V Adaptor - 90 Minutes
The convenient, affordable, portable transport
solution. With a standard conguration of one motor
and one battery - you have the option to upgrade to
a two-motor conguration and upgrade to two
batteries.This is the lightweight, go anywhere dot
board for you.

11
dot REMOTE
dot REMOTE - RC100
The dot board RC100 Remote Controller
offers three ride levels – Novice, Eco and Expert.
Featuring an adjustable grip, soft silicon trigger and
sensor magnets.
Compatible with all dot board models. Firmware
upgradeable via supplied USB dot Data cable.
NOTE:
The usb cable supplied with your dot Board is a special USB
data cable to transfer data to and from your dotboard and
dot Remote.A regular USB charging cable may not work when
attempting to upgrade rmware.

12
dot BATTERY MODULE
dot BATTERY - BM100
The proprietary cell balancing technology in the
dot battery module delivers reliable and safe lithium
battery power in a convenient stackable format.
Each battery is comprised of 10 individualVTC4 lithium-ion
cells, while the battery module itself has passed the rigorous
IEC 62133 standard, the world’s leading benchmark for lithium
battery safety.This means the product will not be damaged from
a short circuit, is safe for airline travel and provides you with
condence during charging, operation and storage of the lithium
battery.
The batteries modules feature an extremely low self-discharge
design. It works in conjunction with dot’s regenerative braking
system to store recovered power.
NEVER open your BM100 Battery module for inspection. If
you have concerns with your BM100, then contact dot boards
BM100 Units are sealed and warranty will be void if the seal is
broken from unauthorized internal inspection

13
dot MAIN CONTROLLER
dot Main Contoller - MC100
The dot Main Controller is the heart of the dot board
system and contains more than ve-hundred
individual components that act in concert to deliver a
super smooth ride experience.
The housing features LED red rear lights with multiple
brightness levels, a magnetic charge port and easy access USB
port for rmware updates.
NEVER open or tamper with the Main Controller for any
reason. If you have concerns with the Main Controller, please
contact customer service. The warranty will be void if you open
or tamper with the Main Controller.

14
BATTERY SAFETY
The dot board BM100 battery module contains
lithium Ion cells, that could explode or cause a re if
they are used incorrectly
Your BM100 battery module has been designed and built with
user safety as a priority but please be aware of the following
precautions:
Always use extreme caution when working with or around any
battery terminals, mounting screws or motors
Always observe and obey the instructions on labels attached to
components - they are there for your safety.
The BM100 has no user serviceable parts. Do not disassemble,
remove or replace battery components. This will void your
warranty.
Do not short circuit the battery terminals at each end. Always
ret the protective caps your battery was supplied with, when
not in use.
Never throw a battery in to a re or submerse in water.
Dispose of your battery as instructed in this owners manual
Changes or modications to your BM100 battery module, can
present a safety risk and will void your battery warranty
If your battery shows any type of damage or shape change (e.g.
bulging, leaking etc..) then discontinue use and immediately
contact dot boards.
Failure to properly follow the safety instructions and precautions,
can cause you to be seriously injured or killed. Always follow the
procedures and precautions in this owner’s manual.
Battery installation and removal.Your dot board
skateboard is shipped with the batteries already tted.
Batteries will be supplied, depending on the quantity
ordered and the maximum amount that can be tted
to your model .
Your dot board case, will come shipped with specic battery
terminal protection caps. Please retain these caps for future use
with transportation – especially for transportation on aircraft.
When tted and with tape to hold caps in place, these protective
caps will help prevent other objects from damaging the battery
connectors and terminals.

15
BATTERY INFORMATION
Approximate Charge Time:
One Battery with Standard 1.5A 48V Adaptor - 60 Minutes
Two Batteries with Standard 1.5A 48V Adaptor - 120 Minutes
Three Batteries with Standard 1.5A 48V Adaptor - 180 Minutes
One Battery with Standard 3.5A 48V Adaptor - 45 Minutes
Two Batteries with Standard 3.5A 48V Adaptor - 90 Minutes
Three Batteries with Standard 3.5A 48V Adaptor - 135 Minutes
Four Batteries with Standard 3.5A 48V Adaptor – 180 Minutes
The Dot Board has the following approximate
range on a full charge:
One Battery 6 Miles*
Two Batteries 12 Miles*
Three Batteries 18 Miles*
Four Batteries24 Miles*
*There are various factors such as the weight of the rider, wind
resistance, and road surface conditions that can reduce range.
Battery Care:
• Do not store the skateboard or battery or charge the
batteries at temperatures at or below 32°F or temperatures
at or above 104°F
• Keep the skateboard and battery away from high temperature
conditions such as direct sunlight, re, heat, inside hot cars,
etc. Exposing the battery to high temperature conditions may
cause the battery to explode resulting in serious injury or
death.
• Store batteries in a cool dry place
• Keep the skateboard and battery away from water, moisture,
rain and ammable and combustible materials
• Do not shock the battery by excessive impact or force (for
example, dropping it, slamming it, or throwing it)
• Do not disassemble, puncture, crush, open, or otherwise
tamper with the battery pack in any way
• Do not allow the battery to run down completely before
charging.
• Periodically charge the battery even if the skateboard has not
been used.
• Charge the battery before storing your skateboard. Leaving
the battery in a completely discharged state may result in the
battery not accepting a charge or a decrease in the charge-
holding capacity
• Regularly inspect the batteries for any damage. If the
batteries shows any sign of damage, leakage, shape change, or
any other indicators of damage, immediately discontinue use.
Do not handle any damaged batteries
• Never get the battery wet, ride in rain, on wet, or icy surfaces.
This may void your warranty and be a safety hazard.
DO NOT insert anything into the connector terminals on the
battery or allow metal to come in contact with the battery
connectors. Doing so could cause a short-circuit and increase
the risk of risk of combustion, re, personal injury or death.
When any battery is not installed and separated from the dot
Board, always put the red safety cap on both the back and front
connectors of the battery. If you do not have the red safety
cap, you may also use battery connector sticker to cover the
connectors.

16
BATTERY INSTALLATION
Depending on the model and conguration you
purchased, your skateboard will come with one, two,
three or four batteries already installed. Depending
on the model and conguration you purchased, you
may have the option of adding additional batteries.
The maximum conguration per model is as follows:
• Compact – two batteries
• Cruiser – three batteries
• Transporter – four batteries
Batteries are attached to the deck with two countersunk screws.
Different models will have different length screws – due to deck
thickness:
Compact and Cruiser – M5 x 16mm 3mm hex
Transporter – M5 x 20mm 3mm hex
To avoid potential shock or other injuries, always
make sure that the power is turned OFF and the
charger is disconnected before removing or installing
batteries. Failure to follow these steps can result in
electrocution or other serious injury.
Installation of Batteries
1. Ensure that the skateboard and the Remote control are
turned off and the battery charging cable is unplugged
from the electrical outlet and the magnetic connector is
disconnected from the charging port of the Control Module.
2. Using the Dot Hex-drive tee bar provided with your dot
Board, remove the battery pack screws from the topside of
the deck that are holding the existing battery pack that is
closest to the front of the skateboard.
3. Flip the skateboard over to expose the underside and
remove the front deector cover from the existing battery.
4. Remove the deck plug from the deck where the where the
additional battery will be installed.
5. The Front installed Battery Module should be removed and
additional Battery Modules should be added between the
Main Controller and the existing front Battery Module so
that the Debris Cap remains at the front.
6. Apply dielectric grease to the battery connector and then
align and slide the additional battery onto the existing
battery ensuring that the batteries are securely connected.
7. Repeat the above steps for any additional batteries you want
to add.
8. Place the sealing cap sticker to the battery connector on the
end battery, closest to the front of the skateboard.
9. Slightly lift the battery closest to the front of the skateboard
and engage the clip of the front deector cover to the
battery and make sure it is securely in place.
10. While supporting the batteries with your hand, carefully ip
the skateboard over right side up.
11. Re-install the battery case screw that were taken off the
existing battery and install additional battery screws through
the top of the deck to hold any additional batteries securely
in place with the Dot Hex-drive tee bar provided with your
dot Board.
12. Wash your hands after handling batteries

17
BATTERY INSTALLATION
Removing or Replacing Batteries
Depending on the model and conguration you purchased, your
skateboard will come with one, two, three or four batteries
already installed. If you wish to remove any batteries or wish to
change out any dead batteries for new ones, here are the steps
for removing batteries:
1. Ensure that the skateboard and the Remote control are
turned off and the battery charging cable is unplugged
from the electrical outlet and the magnetic connector is
disconnected from the charging port of the Control Module.
2. Using the Dot Hex-drive tee bar provided, remove the
deck screws from the topside of the deck of the battery or
batteries that you would like to remove or replace. Make
sure you support the batteries by hand.
3. Turn the skateboard over.
4. Remove the front deection cover.
5. Remove the battery you want to remove or replace.
6. If you are replacing an old battery with a new one, please
make sure to apply dielectric grease to the battery
connectors prior to connecting the new battery.
7. If the end battery that is closest to the front of the
skateboard does not have a Debris-Resistant Cap on the
front of the battery, then install one prior to reinstalling the
front deector cap.
8. Slightly lift the end battery that is installed closest to the
front of the skateboard and engage the clip of the front
deector cover to the battery and make sure it is securely
in place.
9. While supporting the battery or batteries with your hand,
carefully ip over the skateboard right side up.
10. Re-install battery case screws to secure all batteries back in
place.
11. If you removed any batteries, ll the holes where the screws
were with the deck plugs on the top and bottom of the
deck.
12. Check your status light under the Main Controller charge
port cover – you may need to wake the board up, by
spinning a motor wheel. It’s recommended that you charge
all the batteries together once tted, to ensure all the
batteries are charged to the same level. The status light will
indicate Green when charged, the Remote controller will
conrm the charge level of the batteries once it is turned
on.
Never overtighten the battery mounting screws
or force a deck screw that could result in cross
threading the mounting xture. Always check you
have the right length deck screw for your model.
Always check your battery before installation for any
signs of damage, bulging or leakage.
Improper use, storage, handling, disposal of battery or
charger can result in re, electrocution, serious injury
or death.

18
CHARGING THE BATTERIES
The dot skateboard is supplied with a charging
cable tted with a magnetic connector. This cable is
attached to your power adaptor which is connected
to your mains outlet.
To charge the dot board skateboard, the charging
cable MUST be connected in the following
sequence:
1. Remove the protective cap from the magnetic connector and
inspect to ensure that the surface is clean.
2. Remove the charging port seal on the Main Controller
Module and inspect to ensure that the port is clean.
3. Dock the magnetic connector to the charging port of the
Main Controller Module, conrming the connector is
securely connected.
4. Plug the power adapter plug into an electrical outlet.
5. The status light inside of the charging port will be ashing
green when the batteries are charging and then turn solid
green when fully charged.
The battery charging cable MUST be disconnected
in the following sequence:
1. Disconnect the power adapter plug from the electrical outlet.
2. Remove the magnetic connector from the charging port on
the Main Controller Module.
3. Ret the protective cap to the magnetic battery charging
cable and put the protective seal back onto the charging
port of the Main Controller Module.
4. Always put the protective seal back on to the charging port
to assist keeping water, dirt and other debris out.
• Do not charge the batteries at temperatures at or below 0°C
or at temperatures at or above 40°C
• Disconnect the charger after it has been fully charged.
• Do not charge batteries for more than 8 hours
• Unplug the charger from the electrical outlet when not in use.
• Recharge the battery after every use
• Failure to periodically charge the battery may result in the
battery not accepting a charge or decreased charge-holding
capacity.
• Do not charge the batteries while unattended.
• The charger should be examined regularly for damage to the
cord, plug, casing, and other parts. If the charger is damaged,
or emits unusual odor or sounds immediately stop using
the charger until it has been replaced. Use ONLY with the
recommended charger designed specically for the Dot
Board.
• To reduce the risk of combustion, ignition, or explosion,
always charge batteries in a well ventilated area and in
noncombustible conditions

19
CHARGING THE REMOTE
Your RC100 Remote controller comes with its own
lithium Ion rechargeable battery. This is charged by
a USB cable .We recommend you fully charge your
Remote before rst use.
Approximate Charge Time: 180 minutes
Charging The Remote Control Battery
1. Using the USB charging cable provided, connect the Micro
USB connector to the Remote control.
2. Plug the USB charging cable into any USB outlet.
3. Check the level of charge on the Remote control by looking
at the charge level of the display screen on the Remote

20
PAIRING THE REMOTE
Your dot board comes paired with your Remote
control from the manufacturer. If you lose pairing for
any reason, you can pair the Remote and skateboard
by doing the following:
1. Press the down button on the Remote control to power on
the Remote control.
2. Put the dot board in an upside down position and spin either
the hub motor wheel to turn it on.
3. Remove the charging port cover. There will be a ashing
Cyan light that indicates that the Remote control and the
skateboard are not paired.
4. Select the Remote pair option from the menu on the
Remote control – refer to Remote menu features on page
22.
5. Spin-stop the hub motor wheel three times to initiate the
board pairing process.
6. It will momentarily ash Magenta when the spin-stop is done
correctly.
If successful, pairing will occur almost instantaneously. If pairing is
not successful, the Main Controller will revert to Cyan light and
the Remote will remain in pair mode.
Please visit www.dotboards.com for a video showing how
to pair the skateboard with the Remote control.
While pairing your dot board with your Remote
(while the board is upside down), the wheels will spin
if you press on the accelerator. Keep ngers, hair,
other body parts and your clothing away from the
moving parts.