DoubleTake SENTRY User manual

www.DoubleTakeGolfCar.com
CAT-25: Sentry Dash - Yamaha Drive / October 26, 2016 / Manufactured By Custom Golf Car Supply, Inc.
YAMAHA®DRIVE®/
DOUBLETAKE®VORTEX™
IMPORTANT: Read through all instructions before beginning installation.
TABLE OF CONTENTS:
Section 1 - Car Preparation
Section 2 - Sentry Dash Installation
Section 3 - Trim Kit Installation
LOCKING STORAGE DASH
TM
CAR PREPARATION
SECTION 1
Remove the plastic cup holder insert out of the dash, by
unhooking the plastic factory clips under the bottom of the
insert (A flat screw driver may be needed to pry it open).
REMOVE FACTORY CUP HOLDER INSERTS
1:1
Car with factory components removed and ready for
Sentry Dash installation
NOTE: Holes for electronic components should be
cut out prior to mounting the dashboard. These cut
out locations are at user’s discretion.
Reach into dash thru the opening and disconnect all wiring from
electronic components mounted to dash. Make sure to notate
which wires go with which components, if there is more than one
component (Ignition switch, Light switch, etc.).
DISCONNECT COMPONENTS
1:2
Remove the center cap/scorecard holder from center of steering
wheel. Remove lagre nut and pull steering wheel off of steering
column shaft.
REMOVE STEERING WHEEL
1:3
Remove the steering column skirt by unhooking the factory clips
under the skirt. (A flat screw driver may be needed to pry it open.)
REMOVE STEERING COLUMN SKIRT
1:4
Remove the factory dash by removing:
- 4 plastic push-rivets located across the top of the dash
- 2 phillips head screws in the dash face
- 5 plastic push-rivets across the floor board under the dash
REMOVE FACTORY DASH
1:5
Yamaha Drive / DoubleTake Vortex
Remove all electrical components from the factory dash. Set aside
to be installed in Sentry Dash.
REMOVE ELECTRICAL COMPONENTS
1:6

Sentry Dash - Yamaha Drive - Section 2 / pg 2
SENTRY DASH INSTALLATION
SECTION 2
(A) Steering Column
(B) Lower Outer Openings
Slide the Sentry Dash over the steering column (A), while
pulling any wiring for electrical components through the lower
outer openings (B).
NOTE: Wire extensions may need to be added to wiring.
POSITION SENTRY DASH
2:1
Once the dash is fully seated, line up the four upper holes of the
Sentry Dash with the four existing holes in the factory frame (C)
and insert four 1/4” push rivets provided. Next, insert two 3/8”
push rivets provided into the two outside bottom holes that line
up with the existing holes in the floor board (D). (Mounting holes
located at the center bottom of the dashboard are optional.)
ATTACH SENTRY DASH WITH PUSH RIVETS
2:2
(C) Align and install
1/4” push rivets
(C)
(D)
(D) Align and install
3/8” push rivet
(D)

Sentry Dash - Yamaha Drive - Section 3 / pg 3
ATTACH CUP HOLDER INSERTS
3:1
Remove protective film from outer surface of Cup Holder inserts (E). Attach
inserts to Sentry Dash with peel and stick tape provided.
NOTE: Items are left and right handed. Check for correct positioning before
attaching with double-sided tape. The adhesive is automotive quality and
may not be removeable without damage to the insert once applied.
Place and press Cup Holders (F) into insert openings.
(E) Cup Holder Insert
(F) Cup Holders
TRIM KIT INSTALLATION
SECTION 3
(G) Storage Insert
(I) Faceplate Insert
Remove protective film from outer surface of Storage insert (G) and
Nose insert (H). Then attach inserts to Sentry Dash with peel and stick
tape provided.
ATTACH STORAGE AND NOSE INSERTS
3:2
(H) Nose Insert
Cut the necessary holes in the Faceplate insert (I) to install the electrical
components that were taken out in section one. (Placement of these
components varies by user). Install components and reconnect wiring.
PREPARE FACEPLATE
3:3
Snap the Faceplate Tray (J) into the rectangular hole of the
Faceplate insert.
NOTE: This location also accepts a standard radio sleeve.
If a radio is to be installed, do not install the Faceplate Tray.
Install the radio sleeve once the Faceplate insert has been
screwed into place.
INSTALL FACEPLATE TRAY
3:4
Insert the Faceplate Tray and Faceplate insert into the lower dash
opening and attach with the 4 small flat head screws provided.
INSTALL FACEPLATE
3:5
(J) Faceplate Tray
Reattach the steering wheel to the steering column.
Installation is Complete.
REATTACH STEERING WHEEL
3:6