Dover Anthony Infinity 60 Series User manual





CompleteInfinity60Series
InstallationManual
99‐25726‐I001February2023Rev.B





Copyright©2022Anthony,Inc.AnAnthonyCompanyAllrightsreserved.Informationinthisdocumentissubjecttochangewithoutnotice.Nopartofthisdocumentmaybe
reproducedortransmittedinanyformorbyanymeans,electronicormechanical,foranypurpose,withoutpermissionofAnthony,Inc.Allproductandcompanynamesare
trademarks
TM
orregistered®trademarksoftheirrespectiveholders.Useofthemdoesnotimplyanyaffiliationwithorendorsementbythemunlessotherwisespecified .

CompleteInfinity60SeriesInstallationManual
99‐25726‐I001September2023Rev.
C



1|Pagewww.anthonyintl.com

AnthonyLocations
Anthonyisamanufacturerandsolutionsproviderofglassdoors,lightingsystems,anddisplayequipmentforuseincommercial
refrigerationsystems.FormoreinformationonAnthony,pleasevisitwww.anthonyintl.com.
NorthAmericaLocations
Sylmar,CA
CorporateOffices
12391MonteroAvenue
Sylmar,CA91342
Phone:818.365.9451
Toll‐FreeUS:800.772.0900
Canada:800.336.8825
Fax:818.365.2441



Madison,GA
1101SovisRd
Madison,GA30650
Phone:706.342.9300
Fax:706.342.9303







ForReplacementpartsgoto www.anthonystore.com 

Forourlatestinstructionalandinformativevideosvisitourchannel

Forthelatestnewsandupcomingproductreleasesfollowusonthesesocialmediaplatforms:

   
TWITTERYOUTUBELINKEDIN




CompleteInfinity60SeriesInstallationManual
99‐25726‐I001September2023Rev.
C



2|Pagewww.anthonyintl.com


ApplicableWalk‐InModels
Infinity60Series
I60N 

Copyright©2022Anthony,Inc.AnthonyCompanyAllrightsreserved.Informationinthisdocumentissubjecttochangewithoutnotice.Nopartofthisdocumentmaybe
reproducedortransmittedinanyformorbyanymeans,electronicormechanical,foranypurpose,withoutpermissionofAnthony,Inc.Allproductandcompanynamesare
trademarksTMorregistered®trademarksoftheirrespectiveholders.Useofthemdoesnotimplyanyaffiliationwithorendorsementbythemunlessotherwisespecified.
Anthonyproductsidentifiedinthismanualaredesignedandcertifiedtomeetorforsafety,andforsanitationstandards.
Europeanproductsmeetrequirements.

Eachcustomerisresponsibleforfinalsiteapproval.

CompleteInfinity60SeriesInstallationManual
99‐25726‐I001September2023Rev.
C



3|Pagewww.anthonyintl.com

TableofContents
A PPLICABLE W ALK ‐I N M ODELS .................................................................................................................................................................2
INTRODUCTION............................................................................................................................................................................6
P ROPERUSEOF A NTHONY P RODUCTS .........................................................................................................................................................6
Q UALIFIED P ERSONNEL ...........................................................................................................................................................................6
SECTION1‐SAFETY......................................................................................................................................................................7
S AFETY M ESSAGES .................................................................................................................................................................................7
S IGNAL W ORDS .....................................................................................................................................................................................7
S AFETY C OLORS .....................................................................................................................................................................................7
S AFETY A LERTS S YMBOLS .........................................................................................................................................................................8
U SER S AFETY ........................................................................................................................................................................................9
GeneralSafetyRules.............................................................................................................................................................9
Safetyequipment–PersonalProtectiveEquipment............................................................................................................9
ElectricalConnections...........................................................................................................................................................9
Precautionsbeforework.......................................................................................................................................................9
E QUIPMENT L IST &  T OOLS .....................................................................................................................................................................10
I NSTALLATION T IPS ...............................................................................................................................................................................10
SECTION2–STANDARDWALK‐INLINE‐UPFRAMEINSTALLATION.............................................................................................11
T OOLS R EQUIRED .................................................................................................................................................................................11
F RAME U NPACKING ..............................................................................................................................................................................11
Figure2.1:FrameCrate.......................................................................................................................................................11
F RAME H ANDLINGDURING I NSTALLATION .................................................................................................................................................12
Figure2.2:ClampstoinsertFrameintoNetOpening.........................................................................................................12
Figure2.3:MullionsAttentionLabel...................................................................................................................................12
OtherFrameInstallationRecommendations&Suggestions..............................................................................................13
N ET O PENING &  F RAMEINSTALLATION .....................................................................................................................................................14
Figure2.4:FrameAlignment,Squareness,andPlumb.......................................................................................................15
S HIMMINGTHE F RAME .........................................................................................................................................................................16
Figure2.5:FrameShimmingandSealingDetails................................................................................................................17
P ROPERLY S EALINGTHE F RAME ...............................................................................................................................................................18
C ONTINUOUS L INEUP F RAME I NSTALLATION ...............................................................................................................................................19
Two(2)FrameSectionLine‐up...........................................................................................................................................19
Figure2.6:T‐Triminstallation.............................................................................................................................................20
Three(3)ormoreFrameSectionsLine‐up..........................................................................................................................20
Figure2.7:Continuousframesectionslayout.....................................................................................................................21
Figure2.8:T‐Triminstallation.............................................................................................................................................21
Figure2.9:LastFrameinstallation......................................................................................................................................22
Figure2.10:SecondtoLastFrameinstallation...................................................................................................................22
FrameElectricalWiringConnections..................................................................................................................................23
ConduitExitLocation..........................................................................................................................................................23
Figure2.11:ConduitExitlocation......................................................................................................................................23
Figure2.12:WiringLabels..................................................................................................................................................23
Figure2.13:WiringDiagrams.............................................................................................................................................24
SECTION3–DOORUNPACKINGINSTRUCTIONS.........................................................................................................................25
Figure3.1.ShippingCratecontainingAnthonyDoors........................................................................................................26
O PENING S HIPPING C RATE .....................................................................................................................................................................26
Figure3.2.UnscrewingthetopportionoftheShippingCrate............................................................................................27
Figure3.3.RemovingthetopportionoftheShippingCrate..............................................................................................28
Figure3.4.Offsettingcrateweightforremovingdoorsfromthecrate..............................................................................28
Figure3.5.RemovingFrontsideofShippingCrate.............................................................................................................29
R EMOVING D OORSFROM S HIPPING C RATE ................................................................................................................................................30
Figure3.6.RemovingDoorfromShippingCrateCorrectly.................................................................................................30




CompleteInfinity60SeriesInstallationManual
99‐25726‐I001September2023Rev.
C



4|Pagewww.anthonyintl.com

SECTION4–DOORINSTALLATION.............................................................................................................................................31
D OOR H ANDLING .................................................................................................................................................................................31
D OOR I NSTALLATION ............................................................................................................................................................................31
Figure4.1:SeatingDoorontoTorqueMaster....................................................................................................................32
Figure4.2:DielectricGreaseinSOCKET(hingepinplug)receptacle..................................................................................33
Figure4.3:EngageHingePintoFrame...............................................................................................................................34
Figure4.4:Securehold‐openmountingscrew...................................................................................................................35
T ORQUE M ASTER ™ AND S AG A DJUSTMENT ...............................................................................................................................................36
Figure4.5:TorqueMaster™..............................................................................................................................................36
SagAdjustment...................................................................................................................................................................36
TorqueAdjustment:............................................................................................................................................................37
CleanupWorkArea............................................................................................................................................................38
CheckdoorforFunctionality...............................................................................................................................................38
SECTION5‐REQUIREDFUNCTIONALITYFORCOMPLETEINSTALL...............................................................................................39
DoorFrameAssembly.........................................................................................................................................................39
Gasket.................................................................................................................................................................................39
HingePin.............................................................................................................................................................................39
HoldOpenAssembly...........................................................................................................................................................39
TorqueMasterAssembly....................................................................................................................................................39
SECTION6‐COOLER*STORECONDITIONREQUIREMENTS.........................................................................................................40
Table6.1:Operatingconditions..........................................................................................................................................40
O PERATING R EQUIREMENTSAND R ECOMMENDATIONSFOR O PTIMAL P ERFORMANCE .........................................................................................40
Figure6.1ProductStocking–Shelvesrequiredtobefullystocked...................................................................................41
Figure6.2EvaporatorAirDeflector‐Contactevaporatormanufacturerforrecommendedairdeflector.........................41
SECTION7‐ROUTINEPREVENTATIVEMAINTENANCE................................................................................................................42
R ECOMMENDED M AINTENANCE I NSPECTIONAND C LEANING I NTERVALS ...........................................................................................................43
M AINTENANCE R ECOMMENDATIONS ........................................................................................................................................................43
CoolerTemp&DefrostSettings.................................................................................................................................43
Frame&Door.............................................................................................................................................................43
Door/FrameHingingPin&ReceptacleArea...............................................................................................................43
TorqueMaster™..........................................................................................................................................................44
Gaskets.......................................................................................................................................................................44
C LEANING R OUTINE ..............................................................................................................................................................................44
SECTION8‐TROUBLESHOOTING................................................................................................................................................45
Table8.1:InstallationTroubleshooting..............................................................................................................................45
Table8.2:GeneralTroubleshooting....................................................................................................................................46
SECTION9–FRAMEREPLACEMENTPARTS.................................................................................................................................47
Figure9.1FrameAssemblyforInfinity60SeriesNormalTemperatureforReplacementParts.........................................47
Table9.1FrameAssemblyforInfinity60SeriesNormalTemperatureforReplacementPartsList...................................48
SECTION10–DOORREPLACEMENTPARTS................................................................................................................................49
Figure10.1DoorAssemblyforInfinity60SeriesDoor,forReplacementParts..................................................................49
Table10.1DoorAssemblyforInfinity60SeriesReplacementPartsList............................................................................50
SECTION11–OPTIMAX7LEDLIGHTINGFIXTUREREPLACEMENT...............................................................................................51
ReplacementPartNumbers................................................................................................................................................51
R EPLACEMENT I NSTRUCTIONS .................................................................................................................................................................52
EndJambs...........................................................................................................................................................................54
SECTION12–REMOVING&REPLACINGTHETORQUEROD........................................................................................................55
Figure12.1TorqueRodlocation.........................................................................................................................................55
Figure12.2Removingtorquerodfromthedoor................................................................................................................56
Figure12.3Removingtorquerodfromthedoor................................................................................................................56
SECTION13–REMOVING&REPLACINGTHEHOLD‐OPENASSEMBLY.........................................................................................57
R EMOVINGTHE H OLD ‐O PEN A SSEMBLY ....................................................................................................................................................57
Figure13.1Removinghold‐openassemblyfromdoor.......................................................................................................57
R EPLACINGTHE H OLD ‐O PEN A SSEMBLY ....................................................................................................................................................58
Figure13.2Hold‐openAssembly........................................................................................................................................58
SECTION14–REMOVING&REPLACINGTHEHINGEPIN.............................................................................................................59
SECTION15‐TORQUEMASTERREPLACEMENT..........................................................................................................................61
Figure15.1:TorqueMasterReplacement..........................................................................................................................61


CompleteInfinity60SeriesInstallationManual
99‐25726‐I001September2023Rev.
C



5|Pagewww.anthonyintl.com

APPENDIXA‐GASKETREPLACEMENTGUIDELINES.....................................................................................................................63
P RELIMINARY C ONSIDERATIONSFOR S ERVICING G ASKETS ..............................................................................................................................66
ToolsRequired....................................................................................................................................................................66
RecommendationsandSuggestions...................................................................................................................................66
O RDERING R EPLACEMENT G ASKETS .........................................................................................................................................................66
G ASKET R EMOVAL ...............................................................................................................................................................................67
G ASKET I NSTALLATION ..........................................................................................................................................................................67
APPENDIXB–ANTI‐FOGMAINTENANCE....................................................................................................................................69
CareandCleaning...............................................................................................................................................................69
APPENDIXC–POMLOCKINSTALLATION....................................................................................................................................70
FigureC.1:PomLockSpecifications....................................................................................................................................70
S TANDARD POM  L OCK .........................................................................................................................................................................71
FigureC.2:PlugRemoval.....................................................................................................................................................71
FigureC.3:HingePinAccessPlate(lockretainer)...............................................................................................................71
FigureC.4:FrontViewPOMLock........................................................................................................................................72
APPENDIXD–POMLOCKRETROFITTING...................................................................................................................................73
FigureD.1:POMLockRetrofitKit.......................................................................................................................................73
FigureD.2:TemplateOffsetlocation..................................................................................................................................74
FigureD.3:TemplatePlacementonFrameSideview.........................................................................................................74
FigureD.4:AccessPlateAssembly......................................................................................................................................75
FigureD.5:FrontViewPOMLock.......................................................................................................................................75
APPENDIXE–ANTHONYENERGYCONTROLLER.........................................................................................................................76
Features..............................................................................................................................................................................76
Location..............................................................................................................................................................................76
FigureE.1:4‐DoorFrameLayoutExampleforEnergyControllerandSensorLocations.....................................................76
P ROGRAMMING ,  S ETTINGS , AND P ARAMETERS ...........................................................................................................................................77
SensorButton.....................................................................................................................................................................77
FigureE.2:EnergyController(DewPointSensor)...............................................................................................................77
S ETTINGS .........................................................................................................................................................................................77
OffsetStatusIndicatorMode..............................................................................................................................................77
24‐HourHeatMode............................................................................................................................................................78
OffsetSettingOptions.........................................................................................................................................................78
T ROUBLESHOOTING ..............................................................................................................................................................................79
R EPLACEMENT P ART N UMBERS ...............................................................................................................................................................79
R EPLACEMENT I NSTRUCTIONS .................................................................................................................................................................79
APPENDIXF–REPLACINGFRAMEMOUNTEDCYLINDERLOCKS..................................................................................................80
APPENDIXG–RETROFITTINGFORFRAMEMOUNTEDCYLINDERLOCKS.....................................................................................81
T OOLS R EQUIRED .................................................................................................................................................................................81
REVISIONHISTORY.....................................................................................................................................................................84

 

CompleteInfinity60SeriesInstallationManual
99‐25726‐I001September2023Rev.
C



6|Pagewww.anthonyintl.com

Introduction
Thismanualprovidesinformationrequiredtoperforminstallation,repairs,andrequiredmaintenancetotheAnthonyFrames
andDoors.Thismanualisintendedasawrittenguideforpersonnelwhoareproperlytrainedandqualifiedtosafelyusea
varietyofdifferentequipmentandtoolsrequiredduringtheinstallation,repairs,andperformingmaintenanceoftheAnthony
FramesandDoors.
Allpersonnel/contractorsassignedtoinstallAnthonyFrameand/orDoorsmustreadthismanualinitsentiretyasoneofthe
stepsinbeingcertifiedtoinstallandworkonAnthonydoors.Failuretoreadandthoroughlyunderstandthematerialcontained
inthismanualmayultimatelyresultindamagetotheequipment,andinjurytopersonnel,andcouldvoidthewarranty.
Thecomponentsandsystemsdescribedinthismanualmaybeoperatedonlybypersonnelqualifiedforthespecifictaskbythe
relevantdocumentation,warningnotices,andsafetyinstructions.Qualifiedpersonnelarethosewho,basedontheirtraining
andexperiencecanidentifyrisksandavoidpotentialhazardswhenworkingwiththesetypesofcomponentsandsystems.

ProperuseofAnthonyProducts 
Anthony’sproductsmayonlybeusedfortheapplicationsdescribedinthecatalogandtherelevanttechnicaldocumentation.If
productsandcomponentsfromothermanufacturersareused,thesemustberecommendedorapprovedbyAnthony.Proper
transport,storage,installation,assembly,commissioning,operation,andmaintenancearerequiredtoensurethatthe
productsoperatesafelyandwithoutanyproblems.Thepermissibleambientconditionsmustbecompliedwith.
Anthonyhasreviewedthecontentsofthispublicationtoensureconsistencywiththehardwareand/orsoftwaredescribed.
Sincevariancecannotbeprecludedentirely,wecannotguaranteefullconsistency.However,theinformationinthis
publicationisreviewedregularlyandanynecessarycorrectionswillbeincludedinsubsequenteditions.Specificationsand
informationaresubjecttochangewithoutnotice.

QualifiedPersonnel
TheAnthonyproduct/systemsdescribedinthisinstallationmanualshouldonlybeoperatedonlybypersonnelqualifiedforthe
specifictaskfollowingtherelevantdocumentationwarningnoticesandsafetyinstructions.Qualifiedpersonnelwho,basedon
theirtrainingandexperience,canidentifyrisks,andavoidpotentialhazardswhenworkingwiththeseAnthony
products/systems.




CompleteInfinity60SeriesInstallationManual
99‐25726‐I001September2023Rev.
C



7|Pagewww.anthonyintl.com

Section1‐Safety
SafetyMessages
Thismanualincludesgeneral,task‐specific,andimportantSafetyMessages.EachSafetyMessageincludesseveralelements,
SignalWords,SafetyAlertSymbols,SafetyColors,andSafetyMessage.Thefollowingisanexampleofasafetymessagewith
allelementsincluded.

TheseSafetyMessagesaredefinedbythelevelofseverityandarefoundthroughoutthemanualindicatingmeasuresthat
mustbetakenwhileperformingthespecifictaskathand.

SignalWords
DANGER:Indicatesahazardthat,ifnotavoided,WILLresultindeathorseriousinjury.
WARNING:Indicatesahazardwhich,ifnotavoided,COULDresultindeathorseriousinjury.
CAUTION:Indicatesahazardthat,ifnotavoided,WILLresultinminorormoderateinjury.
NOTICE:Indicatesahazardorpracticethat,ifnotavoided,CANresultinequipmentorpropertydamage.
SAFETYINSTRUCTIONS:Indicatessafety‐relatedinstructions,procedures,orthelocationsofsafetyequipment.
SafetyColors
COLOR SAMPLESIGNALWORD
RED DANGER
ORANGE WARNING
YELLOW CAUTION
BLUE NOTICE
GREEN SAFETY INSTRUCTIONS
GREY ASSEMBLY, MAINTENANCE OR SERVICE ALERT



CompleteInfinity60SeriesInstallationManual
99‐25726‐I001September2023Rev.
C



8|Pagewww.anthonyintl.com

SafetyAlertsSymbols
Yoursafetyandthesafetyofothersareveryimportant.ThefollowingSafetyAlertSymbolswillbeusedinconjunctionwiththe
SafetyMessagestowarnofpotentialriskswheninstallingormaintainingyourAnthonyDoor.TheseSafetyAlertSymbols
communicatehazardousinformationquicklyandreinforcetheSafetyMessagewithouttheuseofwordsandacrosslanguage
barriers.ThesesafetymessagesalertyoutopotentialhazardsthatcouldhurtyouorothersorrenderdamagetoAnthony's
products.Eachsafetymessageisassociatedwithasafetyalertsymbol.Thesesymbolsarefoundthroughoutthemanual.The
definitionofthesesymbolsisdescribedbelow:


ProtectiveEyewear–Potentialriskofeyeinjuries,
protectiveeyewearrequiredwhenperforming
this,andanyotherassociatedtasks.
Stop–Beforeyoubegin:Installationofthisassembly
requiresapersonfamiliarwiththeconstructionand
operationofelectricalsystemsandtheHazardsinvolved.
Readinstructionscompletelyandcarefully.

ProtectiveFootwear–Potentialriskofinjuryto
yourfeet,protectivefootwearisrequiredwhen
performingthisandanyotherassociatedtasks.

RiskofElectricalShock–PotentialriskofElectricalShock;pay
closeattentiontoinstructionswhenperformingthisandany
otherassociatedtasks.

ProtectiveGloves–Potentialriskofinjurytoyour
hands,protectiveglovesrequiredwhen
performingthis,andanyotherassociatedtasks.

CommercialRefrigeration–Thissymbolindicatesforuse
insideacommercialrefrigerationcasewithpackagedfoods
only.

HearingProtection–Potentialriskofinjuryto
yourears,protectiveearcoveringsrequiredwhen
performingthis,andanyotherassociatedtasks.
Warning–Toreducetheriskoffire,electricalshockorinjury
observethefollowing:

Usethisunitinthemannerintendedbythemanufacturer.
 Turnthepoweroffbeforeremovingtheexistinglighting
systemandfollowappropriatelockout/tag‐outsafety
procedures


SafetyVest–Wearingahighvisibilityvestis
requiredwhenperformingthisandanyother
associatedtasks.
Heavyobjectsymbol–Singlepersonliftcouldcausemuscle
strainorbackinjury.Gethelpwhenmovingorlifting.Useother
properliftingaids,seekassistance,andalwaysuseproperlifting
techniqueswhenmoving.

LongPants–Wearinglongpantsisrequiredwhen
performingthisandanyotherassociatedtasks.

Note–Thiswillcontaininformationthatishelpfulfora
procedure,condition,oroperation.Readinstructionscompletely
andcarefully.

ReadInstructionssymbol–Readandunderstand
themanualandallothersafetyinstructions
beforeproceeding.

Handlewithcaresymbol–Indicatesthatspecificitemsrequire
carewhenhandling.



PinchHandssymbol–Potentialriskofhandssustaininganinjury
inpinchingpoints.





CompleteInfinity60SeriesInstallationManual
99‐25726‐I001September2023Rev.
C



9|Pagewww.anthonyintl.com

UserSafety
GeneralSafetyRules
Thesesafetyrulesapply:
Alwayskeeptheworkareaclean.
Payattentiontotheriskspresentedbyobstaclesorotherpeopleintheworkarea.
Avoidallelectricaldangers.
Payattentiontotherisksofelectricshockorarcflashhazards.
Alwaysbearinmindtheriskofpinching,electricalaccidents,andbrokenglass.
Alwaysseekassistancefromanotherpersonwhenhandlingframesanddoors

Safetyequipment–PersonalProtectiveEquipment
Usesafetyequipmentaccordingtothecompany,local,andstateregulations.Usethissafetyequipmentwithintheworkarea
whenperforminganytypeofworkonAnthonyDoors:
Safetygoggles
Protectiveshoes
Protectivegloves
LongPants
Hearingprotection
First‐aidkit
OtherSafetydevices

ElectricalConnections
Electricalconnectionsmustbemadeincompliancewithallinternational,national,state,andlocalregulations.Formore
informationaboutrequirements,see“Section2‐FrameElectricalWiringConnections–”ofthismanualdetailingrequirements.

Precautionsbeforework
ObservethesesafetyprecautionsbeforeyouworkontheinstallationorserviceofanyAnthonyproduct:
Provideasuitablebarrieraroundtheworkarea;Forexample,acautionsign/tape,asallowedbythesitemanager.
Ensureallsafetyguardsareinplaceandsecure.
Recognizethesiteemergencyexits,eyewashstations,emergencyshowers,andtoilets.
Ensureaclearpathofretreat.
Ensurethedoorwillnotfalloverand/orinjurepeopleand/ordamageproperty.
Ensureliftingequipmentisingoodcondition.
Whenusingaliftingdevice,safetydevice,orotherequipmentseekassistancewhenneeded.
Ensurethedooristhoroughlyclean.
Ensurequickaccesstoafirst‐aidkit.
Disconnectandlockoutpowerbeforeservicing.



CompleteInfinity60SeriesInstallationManual
99‐25726‐I001September2023Rev.
C



10|Pagewww.anthonyintl.com

EquipmentList&Tools
Thefollowingisalistofallthedifferentequipment,tools,materials,andotherthingsyouwillneedwheninstallingthe
Anthony101NFrameanddoors.
Equipment:  Frame/DoorInstallation:Tools:Materials:
Safemovers
Dollies
Ratchetstraps
Clamps
PalletJack
J‐bar
Broom
2”x4”Studs

Shims
Silicone/Butyl
Caulkgun
4'‐6'level
Rubber/plasticmallet
Wirestripper/cutter
Wirenuts
Tapemeasure
Towels/rags

Voltagetester
SolderingIron
#2Philipsscrewdriver
Flat‐headscrewdriver
Needle‐nosepliers
RazorKnife
Utilityknife
5/32”HexKey
7/16&1/2"wrenches
WirelessDrill/Driver
HighViscosityDielectricgrease
HighViscosityDielectricgrease
ForHarshConditions

(AnthonyP/N:98‐25497‐0001) 
NSFApprovedFoodGrade
SiliconeSealant
PlywoodShims
Foamglasscleaner
(AmmoniaFree)
BlackPaintmarker

InstallationTips
• Completereplacementofwireassembliesisrecommendedwheneverrequired.Splicewiresonlyifnecessary,
usingpropermaterials:suchaselectricaltape,wirenuts,fluxcoresolder,andheatshrink.

• Applyliquidsoaptorailplasticcoversandgasketsuponinstallationtofacilitateinsertionintomountinggrooves.

• Keepdoorsandframescleanforproductefficiency.Thiscanalsohelpreduceenergyconsumptionandpotential
healthhazards.

• Wheneverbindinggasketorplasticpartsusefood‐gradesilicone.

• Alwaysusethecorrecttoolforthejobtobeperformed.Thisensuresproperinstallationandminimizessafety
risks.

• Ifthereisanydoubtabouttheworktobeperformed,consultwithacertifiedtechnicianorAnthony’s
representative.

• Preventativemaintenanceisrecommendedtoensureproductlongevity. 

PROTECTIVEGEARNOTICE

ProtectiveGloves–Potentialriskofinjurytoyourhands,protectivegloves
requiredwhenperformingthis,andanyotherassociatedtasks.
FootwearProtective–Potentialriskofinjurytoyourfeet,wearingprotective
footwearisrequiredwhenperformingthisandanyotherassociatedtasks.



CompleteInfinity60SeriesInstallationManual
99‐25726‐I001September2023Rev.
C



11|Pagewww.anthonyintl.com

Section2–StandardWalk‐InLine‐UpFrameInstallation
ToolsRequired
Referto“EquipmentList&Tools”inSection1foracompletelistofallequipment,tools,materials,andotherthingsneededfor
installation.IftheFramesarenotinstalleduponarrival,theyshouldbeprotectedfromtheenvironmentalconditions,and
ensurestorageoftheproductindoorsatanormalroomtemperatureof75°Forless,donotstoreoutside,weathercan
damagetheframeandcauseissuessuchasplasticdeformation.
PROTECTIVEGEARNOTICE

ProtectiveGloves–Potentialriskofinjurytoyourhands,protectivegloves
requiredwhenperformingthis,andanyotherassociatedtasks.
FootwearProtective–Potentialriskofinjurytoyourfeet,wearingprotective
footwearisrequiredwhenperformingthisandanyotherassociatedtasks.


FrameUnpacking
Beforebeginninginstallationfollowtheinstructionsbelowtounpacktheframesforshippingcratessafelyandeffectively.
1. Locatethefactorypaintedinstructionsonthecratewhichread“OPENONTHISSIDE”(theyarepaintedwithred
ink).
2. Carefully,placethecrateflatonthefloorwiththe“OPENONTHISSIDE”facingup.
3. Removeallscrewsfromthetopandbottomwoodplankstoremove,followedbythecenterplank.
4. Carefully,pulltheframefromthecreateandpreparetoinstallitinthecase.
Figure2.1:FrameCrate

NOTICE
Note–Whenyouhavemultipleframes,pleaserefertothe“ContinuousLineup
FrameInstallation”instructionsinthissection.Dependingonyourconfiguration
youwillhavetwo(2)tothree(3)differentframes(RightFlanged,Continuous,and
LeftFlanged).


CompleteInfinity60SeriesInstallationManual
99‐25726‐I001September2023Rev.
C



12|Pagewww.anthonyintl.com

FrameHandlingduringInstallation
Duringinstallationtakespecialcarenottopushonorusemullionstolifttheframe.Applyingforcetomullionsmaycause
damageandaffecttheframe'soptimalperformance.Ifneeded,werecommendusingeitheraSlidingorSpeedClamptoalign
andsqueezetheFrameintothenetopening(seeFigure2.2).Whenusingclampsensuretograduallysqueezeslowlyto
preventtheframefrombendingorcracking.
PROTECTIVEGEARNOTICE

ProtectiveEyewear–Potentialriskofeyeinjuries,protectiveeyewearrequired
whenperformingthis,andanyotherassociatedtasks.

ProtectiveGloves–Potentialriskofinjurytoyourhands,protectivegloves
requiredwhenperformingthis,andanyotherassociatedtasks.
FootwearProtective–Potentialriskofinjurytoyourfeet,wearingprotective
footwearisrequiredwhenperformingthisandanyotherassociatedtasks.

Figure2.2:ClampstoinsertFrameintoNetOpening
 
*Note:FramepicturedheremaydifferslightlyfromFramefortheInfinity60(yourframewillincludeframemountedgaskets);
Installationisessentaillythesameprocedureandsetrequiredtoinstall.
1. OnceFrame(s)arecompletelyinstalledproceedtoremovetheYellowLabelsfromthemullionsseeFigure2.3
below.
Figure2.3:MullionsAttentionLabel


CompleteInfinity60SeriesInstallationManual
99‐25726‐I001September2023Rev.
C



13|Pagewww.anthonyintl.com


OtherFrameInstallationRecommendations&Suggestions
1. Completereplacementofwireassembliesisrecommendedwheneverrequired.
2. Applyliquidsoaptorailplasticcoversandgasketsuponinstallation,tofacilitateinsertionintomountinggrooves.
3. Keepdoorsandframescleanforproductefficiency.Thiscanalsohelpreduceenergyconsumptionandpotential
healthhazards.
4. Wheneverbindinggasketorplasticpartsonlyusefood‐gradesilicone.
5. Alwaysusethecorrecttoolforthejobtobeperformed.Thisensuresproperinstallationandminimizessafetyrisks.
6. Ifthereisanydoubtabouttheworktobeperformed,consultwithacertifiedtechnicianorAnthony/Anthony
representative.
7. Preventativemaintenanceisrecommendedtoensureproductlongevity.
8. Ensuretohavecorrectreplacementscrewsize,quantity,andtypeifreplacingwithnon‐Anthonyornon‐Anthony
hardware.
9. Donotovertightenscrewswheninstalling.


CompleteInfinity60SeriesInstallationManual
99‐25726‐I001September2023Rev.
C



14|Pagewww.anthonyintl.com

NetOpening&Frameinstallation
ReadtheinstructionsinthisSectioncompletelybeforeinstallingtheframe.Beforeinstallingtheframe,confirmthatthesizeof
thenetopeningaccommodatesthefinishedframe,netopeningshouldbelargerby1/8”thantheframesize,thereshouldbea
gapof1/8"ontop,1/8"ontherightside,and1/8"ontheleftside.Ifthegaptolerancesexceed3/8”,thenetopeningwillhave
tobereducedtoreducethegapwithin1/8”.Also,ensurethatthereisaminimumof3‐1/2”clearancefromfloortotopofthe
bottomsill(opening).

PROTECTIVEGEARNOTICE

ProtectiveEyewear–Potentialriskofeyeinjuries,protectiveeyewearrequired
whenperformingthis,andanyotherassociatedtasks.

ProtectiveGloves–Potentialriskofinjurytoyourhands,protectivegloves
requiredwhenperformingthis,andanyotherassociatedtasks.
FootwearProtective–Potentialriskofinjurytoyourfeet,wearingprotective
footwearisrequiredwhenperformingthisandanyotherassociatedtasks.


Thefollowinginstructionswillensureproperframeinstallation:
1. Wheninstallingtheframe,DONOTinstalltheFramedirectlyonSheetrock,theframeisdesignedtobeinstalledon
Cooler/RefrigerationCases/FreezerBoxesonly.
2. EnsurethattheSealingFrameFlapisfullyengagedto,Sill,Header,andJackStudscreatingasealwithoutanygaps
(seeFigure2.4).
3. MakesuretoDONOTforcetheframeifthefitistootight,doingsomaycauseyoutobreaktheSealingFrameFlapor
tweaktheFrame.
4. Insertamountingscrewintoamountingholeineachcorneroftheframeandtighteneachscrewuntilitis
approximatelyaquarterinchfrombeingflush.
5. Checktheframeisalignedproperlyorsquare.
6. Useameasuringtapetomeasurediagonallyfromonecornertotheoppositeandnotethedistance.
7. Measurethedistancebetweentheremainingtwocorners.
8. Bothmeasurementsshouldbethesame,orwithina1/16”difference.
9. Confirmtheframeandframeflangesareverticallyandhorizontallyaligned(plumb)tothewallsurfacearoundthenet
opening.
10. Placealevelonthetopflangeoftheheaderframetocheckifitishorizontallyaligned.
11. Ifthetopoftheheaderframesagsorbows,correctitasnecessary.
12. Whentheframeiscompletelyaligned,tightenallmountingscrewssecurelyuntileachisflushwiththeframesurface.
DONOTover‐tightenthescrews,asthiscancausetheframetobecomeoutofsquare.
13. Checktheentireframetoensureinstallationiscorrect.Ifneededseerefertothe“ShimmingFrame”sectionfor
instructionsonhowtouseshimstoaligntheframeproperly.

WARNING
Warning:DONOTovertightenscrewsontotheframe,asthismaycausebowing,
sagging,ortheframetobecomeoutofsquare.Thiswillcauseinstallationissues
withDoor'sproperfunction.Adjustedtheframeasneededtoensureitissquare
andfreeofbowingandsags.

CompleteInfinity60SeriesInstallationManual
99‐25726‐I001September2023Rev.
C



15|Pagewww.anthonyintl.com

Figure2.4:FrameAlignment,Squareness,andPlumb





WARNING
Warning:Useonlyfood‐gradesiliconesealant(addcaulkingforlargergaps)toseal
thegapbetweentheframeandthesurroundingwall,insidethecase,cooleror
freezer.NotfollowingtheseprocedurescanvoidAnthony’sService&Warrantyon
condensationandicebuild‐upissues.

CompleteInfinity60SeriesInstallationManual
99‐25726‐I001September2023Rev.
C



16|Pagewww.anthonyintl.com

ShimmingtheFrame
Shimmingisonlytobeusedwhennecessaryandwillprimarilybedoneattheheader(top)oftheframeandopening.Ifthegap
betweentheframeandnetopeningisgreaterthan1/8”,proceedtoshimthegapforaproperfit.RefertoFigure2.5,below
foradetailedviewofShimlocation.Ifeverythingisaligned,squared,plumb,andgapsdonotexceed1/16”skiptheshimming
processandproceedtosealtheFramereferto“SealingtheFrame”belowforinstructions.
PROTECTIVEGEARNOTICE

ProtectiveEyewear–Potentialriskofeyeinjuries,protectiveeyewearrequired
whenperformingthis,andanyotherassociatedtasks.

ProtectiveGloves–Potentialriskofinjurytoyourhands,protectivegloves
requiredwhenperformingthis,andanyotherassociatedtasks.
FootwearProtective–Potentialriskofinjurytoyourfeet,wearingprotective
footwearisrequiredwhenperformingthisandanyotherassociatedtasks.

Thefollowinginstructionswillensuretoproperlyshimframewhennecessary:
1. Acquiresturdy,penetrablematerial,suchasplywood.Thethicknessofthematerialshouldbewedge‐shapedandslightly
lessthanthegaptobefilled,rememberifthegapislargerthan1/8”openingmustbereducedproperlytoaccommodate
theframe.
2. Whenusingshims,theymustbeinstalledfromlefttorightortoptobottom,PARALLELtoframewidthorheight.
3. Measurethelengthofthegap(heightorwidthoftheframe)andcuttheshimmaterialto1/16ofaninchlessthanthe
measuredlength.
4. Installtheshimusingthesametypeofmountinghardwarethatwillbeusedtoinstalltheframe.Becertainthatthe
shiminstallationhardwarewillnotinterferewiththeframeinstallationhardware.
5. Ifnecessary,cutasecondshimtothesamelengthandinstallitontheoppositesideofthenetopening.
6. Iftheadjacentsidesofthenetopeningneedtobeshimmed,repeattheprevioussteps,matchingtheshimlengthto
theframesidesofthenetopening(less1/16ofaninch).
7. ShimsmustNOTbeusedperpendicularly.
8. ExcessshimmaterialMUSTberemovedtoensurepropersealingtotheframe.
A. WhentheFrameextendspastSill,Header,orJackStudsensurethatexcessshimmaterialdoesnotextend
(in‐depth,i.e.,fronttoback)pasttheSill,Header,orJackStuds(seeFigure2.5,Example1below)
B. WhenSill,Header,orJackStudsextendpasttheFrameensurethatexcessshimmaterialdoesnotextend
(in‐depth,i.e.,fronttoback)pasttheFrame(seeFigure2.5,Example2below)

CompleteInfinity60SeriesInstallationManual
99‐25726‐I001September2023Rev.
C



17|Pagewww.anthonyintl.com

Figure2.5:FrameShimmingandSealingDetails


CompleteInfinity60SeriesInstallationManual
99‐25726‐I001September2023Rev.
C



18|Pagewww.anthonyintl.com

ProperlySealingtheFrame
TheelectricalconnectionattheJunctionBoxwherethewiresentertheframe,andwherethewiresentertheracewayinthe
framemustbesealedwithNSFApprovedFoodGradeSiliconeSealant(RTV‐108)atthetimeofinstallation.Ensuretosealthe
gapbetweentheframeandthesurroundingwall,insidethecase,coolerorfreezer.Notfollowingtheseprocedurescanvoid
AnthonyandAnthony’sService&Warrantyoncondensationandicebuild‐upissues.RefertoFigure2.5,onthepreviouspage
forclarification.
ThefollowinginstructionswillensureapropersealoftheFrame:
1. AlwaysensurethatyoucanlocatetheFoaminsertwhichlinestheentireflangearoundtheFrame;DONOTremovethis
foam,itiscriticaltoensureproperinsulation.
2. EnsurethattheSealingFrameFlapisfullyengagedto,Sill,Header,andJackStudscreatingasealwithoutanygaps.
3. Ensurethatanyexcessshimmingmaterialisremovedasinstructedabovein“ShimmingFrame”.
4. IfyourinstallationislikeExample1inFigure2.5,proceedtosealwithSiliconeSealant(RTV‐108)asshown.
5. IfyourinstallationislikeExample2inFigure2.5,proceedtosealwithSiliconeSealant(RTV‐108)asshown.
6. Followthemanufacturer’scuringinstructionsfortheSiliconeSealant(RTV‐108)toensureproperuse.
7. OnceSiliconeSealantiscureddouble‐checkforanyremaininggapsthatrequiremoresealant.

WARNING
Warning:Ensuretousesiliconeapprovedforuseincommercialrefrigerationapplicationswhich
meetsallrequirementsandguidelines.Useonlyfood‐gradesiliconesealant(addcaulkingforlarger
gaps)tosealthegapbetweentheframeandthesurroundingwall,insidethecase,coolerorfreezer.
NotfollowingtheseprocedurescanvoidAnthony’sService&Warrantyoncondensationandice
build‐upissues.




CompleteInfinity60SeriesInstallationManual
99‐25726‐I001September2023Rev.
C



19|Pagewww.anthonyintl.com

ContinuousLineupFrameInstallation
Usethefollowinginstructionsforwalk‐inline‐upswhenmorethanoneframesection(s)isrequired(appliesto101N,101B&
101Twalk‐inconfigurationswithmorethanoneframe).Theseinstructionswillguideyouonhowtoinstallmultipleframes
usingtheprovidedT‐Trim(s)whichsealsthegapbetweenanytwo(2)frames.Whetheryouhavetwoormoreframesusethe
instructionsbelowtoensureproperinstallationoftheentireframeline‐up.Whenyourinstallationonlyrequiresoneframe
sectionthereisnoneedforT‐Triminstallation.

NOTICE
Note–Theseinstructionsapplyonlytothe101N,101B,and101TinbothNormal
TemperatureandLow‐Temperaturewalk‐inapplicationsonly.ForPass‐Thru
configurationspleasereferto“Section18–Pass‐ThruDoorInstallation”for
instructionsoninstallation(whicharelimitedto1and2doorconfigurations).


PROTECTIVEGEARNOTICE

ProtectiveEyewear–Potentialriskofeyeinjuries,protectiveeyewearrequired
whenperformingthis,andanyotherassociatedtasks.

ProtectiveGloves–Potentialriskofinjurytoyourhands,protectivegloves
requiredwhenperformingthis,andanyotherassociatedtasks.
FootwearProtective–Potentialriskofinjurytoyourfeet,wearingprotective
footwearisrequiredwhenperformingthisandanyotherassociatedtasks.


Two(2)FrameSectionLine‐up
Thefollowinginstructionsareforinstallationsthatrequiredtwo(2)framesectionsonly:
1. Tobegin,setthefirstframe(ensurethatthefirstframehasafullflangeontherightsideandcontinuousflange
ontheleftside)againstthefar‐rightsideofthenetopening/caseopeningandinstallaccordingtoinstructions
previouslynotedinthissectionensuringtosquare,plumb,secure,andsealthefirstframe(shimifneeded).

2. Ensurethefirstframeisinstalledcorrectly,thensetthesecondframeintothenetopening/caseopening(ensure
thatthesecondframehasafullflangeontheleftsideandacontinuousflangeontherightside).Slidethesecond
frametothefarleftofthenetopening/caseopeningandslideitsnugframeagainsttheopening.Ensureto
square,plumb,secure,andsealtheframe(shimifneeded).Useinstructionsgivenonpreviouspages.

3. AfterinstallingthesecondframeinsertaT‐Trimbetweenthefirstandsecondframes.

4. OnceT‐Trimisinplace,insertbindingbolts(sexbolts)throughtherightsideofthefirstframe,andintotheleft
sideofthesecondframe.Tightenuntilframesarepulledtogether.RefertoFigure2.6.