DPE Medical DST 8000 User manual

DST8000 Triple/Pro -Unpacking and Assembly Instructions
1. Each package has a drawing attached to it. Remove the pat from the package
only when needed for assembly
2. During assembly you will connect two low current electrical sockets/outlets, like this:
B
A
3. Each part has its bolts and nuts for assembly in its package. You will find some extra
nuts and bolts packed with a note: “Spare”.
4. Start by removing the top of the crate. It will be used as a ramp to roll off the main
part from the crate’s floor.
5. Remove this wall first and take out part # 11. Put it aside. This part weight 33 kg.
(70 lbs.)
-1-
Important: a. It is essential to read a few times all instructions before beginning.
b. If something is not clear or if you are uncertain how to proceed,
stop and contact support at: inf[email protected]
C. pictures can vary, depending on your model
(Applicable to computerized model only)
part # 11
Note:
Two people needed to take out this parts

-2-
6. Remove the remaining walls of the crate
7. Take out all wrapped parts. Leave them in their packages for now.
8. Part #12 (main part of the DST Triple, which is now on the crate's floor), has
retractable wheels. Take out the Lifting handle from the front ramp, lift the unit on its
wheels and roll off the main part, using the top of the crate as a ramp. Locate the main
part at its final position in the room. After completing the assembly of the DST Triple it is
impossible to move it. Important: fold the wheels when the main part is its final location.
Use the Lifting handle attached to
the front ramp and lift the unit on
its wheels by turning the front
and rear levers.
Rear Lever
Front Lever
Lifting handle
The top of the crate used as a ramp
to roll off the main part from the
crate to the flor.

-3-
9. Tips for locating the unit in the room:
48 in.
16 in.

-4-
10. After placing the main part (part #12) at its final location and folding the wheels,
connect part #11 as shown. Be carful not to pinch the electric cables shown at step 12.
A
B
C
D
E
Part #11
Part #12
remove the bolts
Tighten the bolts

-5-
11. Connect tied the plug to the socket as shown.
No wires above this bracket
(Applicable to computerized model only)

-6-
Another look on steps 11 and 12
Before
After

-7-
12. Unfold the big ramp and the little ramp as shown. These ramps are connected.
Two people are needed for this step.
A
BD
CBig ramp Little ramp

13. Connect the plug to the socket as shown
Lie down and look this direction.
You will see two connectors marked below
as A and B. Connect them together.
AB
Before
connection
After
connection
-8-
(Applicable to computerized model only)

-9-
14. Unfold the little ramp.
A
B
A

-10-
15. Connect the black press-fasteners of the bellow to part #11 (the frame of the slope).
Insert the bellow’s black press-fasteners
to the appropriate holes in the frame
Remove the
white zip tie

-11-
16. Connecting the bellow track (part #15) to the big ramp (part #13). The track on the
other side is part #14
overview
Bolts needed are attached to each track

-12-
17. Assemble part #1 (Right small slope cover) as shown.
Approach part #1 to the
external post as shown.
Part #1
Turn part #1 clockwise
and lower it as shown.
A
C
B
Repeat the action on the other side with part #2
Insert bolts

-13-
18. Assemble part #5 (Right long slope cover) as shown.
Part #5
Repeat the action on the other side with part #4

-14-
19. Assemble part #3 (Diagonal reinforcement) as shown.
Note:
1. Assemble the next 3 Diagonal reinforcements in the same way.
Adjust the foot

-15-
20. Computer set up.
Cut the Zip-tie
A
E
C
BRemove and
keep this bolt
Turn and lift the computer
T i g h t e n t h e b o l t s
D
(Applicable to computerized model only)

-16-
21. Unfold the front ramp.
A
B

-17-
22. Assembling part #10 (Slope right handrail)
A
Bronze bearing
BC
DE

-18
23. Assemble the rest of the handrails at the same way as described in the previous page
Connect part #9 here
Connect part #7 here
Connect part #8 here
25. Double-check your assembly. Connect the two plugs to the wall outlet and continue
with the User Guide.
A chain is available to prevent
patients from going down the slope

-19-
26. Index of the detachable parts:
Part #1
Part #3
Part #2
Part #5
Part #4
Part #7
Part #9
Part #8
Part #11
Part #10