Draytek VigorSwitch G1080 User manual

iii

iv
Intellectual Property Rights (IPR) Information
Copyrights © All rights reserved. This publication contains information that is protected by
copyright. No part may be reproduced, transmitted, transcribed, stored in a
retrieval system, or translated into any language without written permission from
the copyright holders.
Trademarks The following trademarks are used in this document:
Microsoft is a registered trademark of Microsoft Corp.
Windows, Windows 95, 98, Me, NT, 2000, XP, Vista, 7, 8 and Explorer are
trademarks of Microsoft Corp.
Apple and Mac OS are registered trademarks of Apple Inc.
Other products may be trademarks or registered trademarks of their respective
manufacturers.
Safety Instructions and Approval
Safety
Instructions
Read the installation guide thoroughly before you set up the device.
The device is a complicated electronic unit that may be repaired only be
authorized and qualified personnel. Do not try to open or repair the device
yourself.
Do not place the device in a damp or humid place, e.g. a bathroom.
Do not stack the devices.
The device should be used in a sheltered area, within a temperature range of +5
to +40 Celsius.
Do not expose the device to direct sunlight or other heat sources. The housing
and electronic components may be damaged by direct sunlight or heat sources.
Do not deploy the cable for LAN connection outdoor to prevent electronic shock
hazards.
Keep the package out of reach of children.
When you want to dispose of the device, please follow local regulations on
conservation of the environment.
Warranty
We warrant to the original end user (purchaser) that the device will be free from
any defects in workmanship or materials for a period of one (1) year from the date
of purchase from the dealer. Please keep your purchase receipt in a safe place as it
serves as proof of date of purchase. During the warranty period, and upon proof of
purchase, should the product have indications of failure due to faulty workmanship
and/or materials, we will, at our discretion, repair or replace the defective
products or components, without charge for either parts or labor, to whatever
extent we deem necessary tore-store the product to proper operating condition.
Any replacement will consist of a new or re-manufactured functionally equivalent
product of equal value, and will be offered solely at our discretion. This warranty
will not apply if the product is modified, misused, tampered with, damaged by an
act of God, or subjected to abnormal working conditions. The warranty does not
cover the bundled or licensed software of other vendors. Defects which do not
significantly affect the usability of the product will not be covered by the warranty.
We reserve the right to revise the manual and online documentation and to make
changes from time to time in the contents hereof without obligation to notify any
person of such revision or changes.
Be a Registered Owner
Web registration is preferred. You can register your Vigor device via http://www.draytek.com.
Firmware & Tools Updates
Due to the continuous evolution of DrayTek technology, all devices will be regularly upgraded. Please
consult the DrayTek web site for more information on newest firmware, tools and documents.
http://www.draytek.com

iv
EU Declaration of Conformity
We DrayTek Corp. , office at No.26, Fu Shing Road, HuKou County, Hsin-Chu Industry Park,
Hsinchu 300, Taiwan , R.O.C., declare under our sole responsibility that the product
Product name: Smart Lite Giga Switch
Model Number: VigorSwitch G1080
Manufacturer: DrayTek Corp.
Address: No.26, Fu Shing Road, HuKou County, Hsin-Chu Industry Park,
HsinChu 300, Taiwan, R.O.C
is in conformity with the relevant Union harmonisation legislation:
EMC Directive 2014/30/EU, Low Voltage Directive 2014/35/EU and RoHS 2011/65/EU with
reference to the following standards
Standard Version / Issue date
EN 55032 2015 Class B
EN 61000-3-2 2014 Class A
EN 61000-3-3 2013
EN 55024 2010+A1:2015
EN 60950-1 2006 +A11:2009 +A1:2010 +A12:2011+
A2:2013
Hsinchu 22nd June, 2017 Calvin Ma / President .
(Place) (Date) (LegalSignature)

1
Regulatory Information
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device may accept any interference received, including interference that may cause undesired
operation.
Caution: Any changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
More update, please visit www.draytek.com.

2
P
Pa ac ck ka ag ge e C Co on nt te en nt t
The 8 ports, Smart Lite Giga Switch is a standard switch that meets both IEEE
802.3u/ab Fast Ethernet and Gigabit Ethernet specifications.
The network administrator can logon the switch to monitor, configure and control
each port’s activity. In addition, the switch implements the QoS (Quality of Service)
and VLAN. It is suitable for office application.
Vigor Device
Quick Start Guide
The type of the power adapter depends on the country that the device will be
installed.
UK-type Power Adapter
EU-type Power Adapter
USA/Taiwan-type Power Adapter
AU/NZ-type Power Adapter
If any of these items is found missing or damaged, please contact your local supplier
for replacement.

3
P
Pa an ne el l E Ex xp pl la an na at ti io on n
LED Status Explanation
On (Green) The device is powered on and runs normally.
PWR Off The device is not ready or is failed.
On (Green) The device is connected with 1000Mbps.
On (Amber) The device is connected with 10/100Mbps.
Blinking The system is sending or receiving data through
the port.
RJ 45 LNK/ACT
for Ports 1 ~ 8
Off The port is disconnected or the link is failed.
Interface Description
RST Reset to the default settings.
RJ 45 LNK/ACT Port 1 ~ 8 Port 1 to Port will be used for Ethernet
connection.
Interface Description
Security hole.
Connecter for a power adapter.
RJ45LNK/ACTPort1toPort8

4
H
Ha ar rd dw wa ar re e I In ns st ta al ll la at ti io on n
Before starting to configure the device, you have to connect your devices correctly.
A hierarchical network with minimum levels of device may reduce the timing delay
between server and client station. Basically, with this approach, it will minimize the
number of devices in any one path; will lower the possibility of network loop and will
improve network efficiency. If more than two devices are connected in the same
network, select one device as Level 1 device and connect all other devices to it at
Level 2. Server/Host is recommended to connect to the Level 1 device. This is general
if no VLAN or other special requirements are applied.
All device ports are in the same local area network.

5
S
So of ft tw wa ar re e C Co on nf fi ig gu ur ra at ti io on n
Before using the device, perform the following steps:
1. Set up a physical path between the configured the device and a PC by a qualified UTP
Cat. 5e cable with RJ-45 connector.
If a PC directly connects to the device, you have
to setup the same subnet mask for PC and the
device. Default values of the managed device
are listed as follows:
2. After configuring correct IP address on your
PC, open your web browser and access
device's IP address.
3. The home page of VigorSwitch G1080 will be shown as below:
IP Address 192.168.1.224
Subnet Mask
255.255.255.0
DHCP Client Enabled (On)
Password admin