Draytek VigorSwitch P2100 User manual

iii

iii
VigorSwitch P2100/G2100
L2+ Managed Switch
Quick Start Guide
Version: 1.0
Firmware Version: V2.6.5
(For future update, please visit DrayTek web site)
Date: January 27, 2021
Copyrights © All rights reserved. This publication contains information that is protected by copyright. No part
may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any
language without written permission from the copyright holders.
Trademarks The following trademarks are used in this document:
Microsoft is a registered trademark of Microsoft Corp.
Windows, Windows 8, 10 and Explorer are trademarks of Microsoft Corp.
Apple and Mac OS are registered trademarks of Apple Inc.
Other products may be trademarks or registered trademarks of their respective
manufacturers.
Safety Instructions
Read the installation guide thoroughly before you set up the switch.
The switch is a complicated electronic unit that may be repaired only be authorized and
qualified personnel. Do not try to open or repair the switch yourself.
Do not place the switch in a damp or humid place, e.g. a bathroom.
Do not stack the switches.
The switch should be used in a sheltered area, within a temperature range of 0 to +45
Celsius.
Do not expose the switch to direct sunlight or other heat sources. The housing and
electronic components may be damaged by direct sunlight or heat sources.
Do not deploy the cable for LAN connection outdoor to prevent electronic shock hazards.
Keep the package out of reach of children.
When you want to dispose of the switch, please follow local regulations on conservation of
the environment.
Warranty
We warrant to the original end user (purchaser) that the switch will be free from any defects in
workmanship or materials for a period of two (2) years from the date of purchase from the dealer.
Please keep your purchase receipt in a safe place as it serves as proof of date of purchase. During
the warranty period, and upon proof of purchase, should the product have indications of failure
due to faulty workmanship and/or materials, we will, at our discretion, repair or replace the
defective products or components, without charge for either parts or labor, to whatever extent
we deem necessary tore-store the product to proper operating condition. Any replacement will
consist of a new or re-manufactured functionally equivalent product of equal value, and will be
offered solely at our discretion. This warranty will not apply if the product is modified, misused,
tampered with, damaged by an act of God, or subjected to abnormal working conditions. The
warranty does not cover the bundled or licensed software of other vendors. Defects which do not
significantly affect the usability of the product will not be covered by the warranty. We reserve
the right to revise the manual and online documentation and to make changes from time to time
in the contents hereof without obligation to notify any person of such revision or changes.

v
EU Declaration of Conformity
We DrayTek Corp. , office at No.26, FuShing Road, HuKou, HsinChu Industrial Park, Hsinchu 303,
Taiwan , R.O.C., declare under our sole responsibility that the product
Product name: PoE 8+2 Gigabit Switch
Model number: VigorSwitch P2100
Manufacturer: DrayTek Corp.
Address: No.26, Fushing Rd., Hukou, Hsinchu Industrial Park, Hsinchu 303,
Taiwan
is in conformity with the relevant Union harmonisation legislation:
EMC Directive 2014/30/EU, Low Voltage Directive 2014/35/EU and RoHS 2011/65/EU with reference
to the following standards
Standard Version / Issue date
EN 55032 2012+AC:2013 class A
EN 61000-3-2 2014 Class A
EN 61000-3-3 2013
EN 55035 2017
EN 62368-1 2014 +A11:2017 (Second Edition)
Hsinchu October 3, 2019 Calvin Ma / President
(place) (date) (Legal Signature)

vi
EU Declaration of Conformity
We DrayTek Corp., office at No.26, Fu Shing Road, HuKou County, Hsin-Chu Industry Park, Hsinchu
300, Taiwan , R.O.C., declare under our sole responsibility that the product
Product name: 8+2 Gigabit Switch
Model number: VigorSwitch G2100
Manufacturer: DrayTek Corp.
Address: No.26, Fu Shing Road, HuKou County, Hsin-Chu Industry Park,
Hsinchu 300, Taiwan , R.O.C.
is in conformity with the relevant Union harmonisation legislation:
EMC Directive 2014/30/EU, Low Voltage Directive 2014/35/EU and RoHS 2011/65/EU with reference
to the following standards
Standard Version / Issue date
EN 55032 2012+AC:2013 class A
EN 61000-3-2 2014 Class A
EN 61000-3-3 2013
EN 55035 2017
EN 62368-1 2014 +A11:2017 (Second Edition)
Hsinchu October 3, 2019 Calvin Ma / President
(place) (date) (Legal Signature)
Regulatory Information
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device may accept any interference received, including interference that may cause undesired operation.
Company name ABP International Inc.
Address 13988 Diplomat Drive Suite 180 Dallas TX 75234
ZIP Code 75234 E-mail [e-mail]
USA Local Representative Contact Person Mr. Robert Messer Tel. [phone]
Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

1
1
1. . P Pa ac ck ka ag ge e C Co on nt te en nt t
VigorSwitch Quick Start Guide
Rack Mount Kit (brackets) Console Cable
The type of the power cord depends on the country that the switch will be installed.
UK-type Power Cord EU-type Power Cord
USA/Taiwan-type Power Cord AU/NZ-type Power Cord
If any of these items is found missing or damaged, please contact your local supplier
for replacement.
Note The following limitation is suitable for VigorSwitch P2100
Power Output --
IEEE 802.3af Max. 15.4W Output Supported
IEEE 802.3at Max. 30W Output Supported
PoE Power Budget –-
140 Watts (Max)

2
2
2. . P Pa an ne el l E Ex xp pl la an na at ti io on n
LED Status Explanation
On (Green) Devices connected over the PoE maximum power budget.
Blinking (Green) More than 80% of maximum power budget is supplied for PoE device(s).
PoE (for
P2100)
Off Devices connected within the PoE maximum power budget.
On (Green) The device is connected with 1000Mbps.
On (Amber) The device is connected with 10/100Mbps.
Blinking The system is sending or receiving data through the port.
RJ 45
LNK/ACT Port
1 ~ 8
Off The port is disconnected or the link is failed.
On (Green) The device is connected with 1000Mbps.
On (Amber) The device is connected with 10/100Mbps.
Blinking The system is sending or receiving data through the port.
Port 9 ~ 10
SFP LNK/ACT
Off The port is disconnected or the link is failed.
On (Green) The switch finishes system booting and the system is ready.
Blinking (Green) The switch is powered on and starts system booting.
SYS
Off The power is off or the system is not ready / malfunctioning.
On The device is powered on.
PWR Off The device is powered off.
Interface Description
RJ 45 LNK/ACT Port 1 ~ 8
PoE for Port 1 ~ 8
Port 1 to Port 8 can be used for Ethernet connection and PoE connection,
depending on the device connected.
Console Used to perform telnet command control.
SFP LNK/ACT Port 9 ~ 10 Port 9 to Port 10 are used for fiber connection.
RST Factory reset button.
Press it to reboot the system. (<5 seconds) The PoE/Alert and SYS LEDs will
blink too.
Press it to reset the system with factory default settings. (5~20 seconds)
The PoE/Alert and SYS LEDs will be off if RST button is pressed between 5
seconds and 10 seconds.
Power inlet for AC input (100~240V/AC, 50/60Hz).
SFP
LNK/ACT
CONSOLE
RJ45 LNK/ACT
Port 1 to Port 8
PoE for Port 1 to Port 8

3
3
3. . H Ha ar rd dw wa ar re e I In ns st ta al ll la at ti io on n
3
3. .1 1 N Ne et tw wo or rk k C Co on nn ne ec ct ti io on n
Use a Cat. 5e twisted-pair cable to connect a PoE device to the port (1~8) of
this switch.
The switch will supply power to PoE Device over the twisted-pair cable.
Please note that Power Device must comply with IEEE 802.3af/at.
Other PCs, servers and network devices can be connected to the switch using
a standard ‘straight through’ twisted pair cable.
(Take VigorSwitch P2100 as an example.)
3
3. .2 2 R Ra ac ck k- -M Mo ou un nt te ed d I In ns st ta al ll la at ti io on n
The switch can be installed easily by using rack mount kit.
1. Attach the brackets to the chassis of a 19- or a
23-inch rack. The second bracket attaches the
other side of the chassis as above procedure.
2. After the bracket installation, the
VigorSwitch’s chassis can be installed in a rack
by using four screws for each side of the rack.
(Take VigorSwitch P2100 as an example.)

4
4
4. . S So of ft tw wa ar re e C Co on nf fi ig gu ur ra at ti io on n
In this section, we take VigorSwitch P2100 as an example:
Before using the switch, perform the following steps:
1. Set up a physical path between the configured the switch and a PC by a
qualified UTP Cat. 5e cable with RJ-45 connector.
If a PC directly connects to the switch, you have to setup the same subnet mask for
PC and the switch. Default values of the managed switch are listed as follows:
IP Address 192.168.1.224
Subnet Mask 255.255.255.0
DHCP Client Enabled (On)
Username admin
Password admin
2. After configuring correct IP address on your PC, open your web browser and
access switch's IP address.
The home page of VigorSwitch will be shown as below:

5
C
Cu us st to om me er r S Se er rv vi ic ce e
If the switch cannot work correctly after trying many efforts, please contact your
dealer for further help right away. For any questions, please feel free to send
e-mail to [email protected].
GPL Notice This DrayTek product uses software partially or completely licensed under
the terms of the GNU GENERAL PUBLIC LICENSE. The author of the software
does not provide any warranty. A Limited Warranty is offered on DrayTek
products. This Limited Warranty does not cover any software applications or
programs.
To download source codes please visit:
http://gplsource.draytek.com
GNU GENERAL PUBLIC LICENSE:
https://gnu.org/licenses/gpl-2.0
Version 2, June 1991
For any question, please feel free to contact DrayTek technical support at
[email protected] for further information.
B
Be e a a R Re eg gi is st te er re ed d O Ow wn ne er r
Web registration is preferred. You can register your Vigor router via
https://myvigor.draytek.com.
F
Fi ir rm mw wa ar re e & & T To oo ol ls s U Up pd da at te es s
Due to the continuous evolution of DrayTek technology, all switches will be regularly upgraded.
Please consult the DrayTek web site for more information on newest firmware, tools and
documents. https://www.draytek.com