Draytek vigorswitch p1090 User manual

V
Vi ig go or rS Sw wi it tc ch h P P1 10 09 90 0
8
8 G Gi ig ga ab bi it t P Po or rt t
P
Po oE E S Sw wi it tc ch h
Quick Start Guide
European Community Declarations
Manufacturer: DrayTek Corp.
Address: No. 26, Fu Shing Road, HuKou Township, HsinChu Industrial Park, Hsin-Chu, Taiwan 303
Product: VigorSwitch P1090
DrayTek Corp. declares that VigorSwitch P1090 is in compliance with the following essential requirements and other relevant
provisions of 2004/108/EC.
The product conforms to the requirements of Electro-Magnetic Compatibility (EMC) Directive 2004/108/EC by complying with
the requirements set forth in EN55022/Class B.
The product conforms to the requirements of Low Voltage (LVD) Directive 2006/95/EC by complying with the requirements
set forth in EN60950-1.
Regulatory Information
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device may accept any interference received, including interference that may cause undesired operation.
We warrant to the original end user (purchaser) that the switch will be free from any defects in workmanship or materials for a
period of two (2) year from the date of purchase from the dealer.
Version: 1.01
Date: December 08, 2014

Package Content
This switch provides 8 10/100/1000M PoE ports. It was designed for easy
installation and high performance in an environment where PoE devices
might need to be connected to the network.
The switch consists of 8 PSE/PoE ports. Providing power to devices via PoE
can offer a solution where power outlet availability is limited and offer the
system designer a flexible solution to locate the network device anywhere.
This is particularly useful for wall-mounted devices such as IP Cameras
where the ideal location to position the device is not nearby a power outlet.
The compact rigid desktop size was specifically designed for small to
medium workgroups. It can be installed where space is limited; moreover, it
provides smooth network migration and an easy way to upgrade to network
capacity.
Quick Start Guide Rack mount kit
(brackets)
USA-type power cord UK-type power cord EU-type power cord
Note: If any of these items is found missing or damaged, please contact
your local supplier for replacement.

Descriptions of Panel
LED Status Explanation
On
(Green) The device is powered on.PWR
Off The device is powered off.
Blinking
(Red) There is a loop existing.Loop
Off There is no loop existing.
On
(Green) A normal connection is through its corresponding
port.
Off LAN is disconnected.
ACT
Blinking
(Green) Data is transmitting (sending/receiving).
On Connect to a Power Device.
Port1~8 Support PoE power feeding (IEEE 802.3af).
Port1~4 Support PoE+ power feeding (IEEE
802.3at).
PoE
Off No Power Device is connected.
Interface Description
Power inlet for AC input (100~240V/AC, 50/60Hz).
1/0 (ON/OFF) - Power switch.
Power Output -- IEEE 802.3af Max. 15.4W Output Supported;
IEEE 802.3at Max. 30W Output Supported
PoE Power Budget -- 130 Watts (Max)


Installing Your Switch
Power Device to This Switch and Getting 48V Power Source through
Cat. 5 Cable
Use a Cat. 5 twisted-pair cable to connect a PoE device to the port (1~8) of this
switch. The switch will supply 48V power to PoE Device over the twisted-pair
cable. Please note that Power Device must comply with IEEE 802.3af/at. Other
PCs, servers and network devices can be connected to the switch using a
standard ‘straight through’ twisted pair cable.
The switch can be installed
easily by using rack mount
kit. However, due to
environmental limitation,
the wall-mount installation
might be required. Simply
follow the steps below:
1. The two slots located on
the switch’s bottom
panel are for device
wall-mount use. The
distance between the two
slots is 7.8 inches
(198.02 mm). Attach two
screws on the wall, so
that the switch’s
wall-mount slots line up
with the two screws.
2. Use drill bit to insert the two
plastic screws into the wall.
3. Insert the two iron screws into the
hole of the two plastic screws
respectively.
4. Place the switch onto the iron
screws through the wall-mount
slots to make the switch hanging
on the wall.