Dream On Me 626 User manual

1
WARNING:
READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF
PRODUCT.KEEP INSTRUCTIONS FOR FUTURE USE.
THIS PRODUCT MEETS OR EXCEEDS SPECIFICATIONS AS ISSUED
BY THE CONSUMER PRODUCT SAFETY FOR NON-FULLSIZE BABY
CRIBS.
CAUTION:BEFORE USING THIS UNIT RECHECK ALL SCREWS TO
BE SURE THEY ARE TIGHTENED SECURELY. A PERIODIC CHECK
SHOULD BE MADE OF ALL SCREWS&NUTS TO BE SURE THEY
REMAIN TIGHT.
INFANTS CAN SUFFOCATE.
* IN GAPS BETWEEN A MATTRESS TOO SMALL OR TOO THICK AND
PRODUCT SIDES.
* ON SOFT BEDDING NEVER ADD A MATTRESS. PILLOW
COMFORTER, OR PADDING.
CAUTION:ANY MATTRESS USED IN THIS CRIB MUST BE AT LEAST
23 3/4 INCHES BY 37-3/4 INCHES WITH A THICKNESS NOT
EXCEEDING 2 INCHES.
PLEASE NOTE THAT THE WARNING STICKER IS PLACED ON THE
CRIBS TO KEEP PARENTS AND CAREGIVERS INFORMED IT IS A
REQUIREMENT BY LAW UNDER CPSC AND ASTM. WE DO
APOLOGIZE FOR ANY INCONVENIENCE THIS MAY CAUSE YOU.
ASSEMBLY INSTRUCTIONS
ITEM NO: 626
Dream On Me Inc.
1532 S WASHINGTON AVE
PISCATAWAY TWP NJ 08854
OFFICE: 732-752-7220
CUSTOMER SERVICE: 732-366-1788
626

2

3
FAILURE TO FOLLOW THESE WARNINGS AND THE INSTRUCTIONS
COULD RESULT IN SERIOUS INJURY OR DEATH.SUFFOCATION
HAZARD-TO HELP PREVENT SUFFOCATION FROM ENTRAPMENT.
WE RECOMMEND A DREAM ON ME MATTRESS/PAD.
DO NOT USE PLASTIC SHIPPING BAG OR OTHER PLASTIC FILM AS
MATTRESS COVERS NOT SOLD AND INTENDED FOR THAT
PURPOSE. THEY CAN CAUSE SUFFOCATION.
DO NOT PLACE PRODUCT NEAR WINDOW WHERE CORDS FROM
BLINDS OR DRAPES CAN STRANGLE A CHILD. STRINGS CAN
CAUSE STRANGULATION!
DO NOT PLACE ITEMS WITH A STRING AROUND A CHILD'S NECK.
SUCH AS HOOD STRINGS OR PACIFIER CORDS.
DO NOT SUSPEND STRINGS OVER A PRODUCT OR ATTACH
SPRINGS TOTOYS.
DO NOT TIE PACIFIERS, NECKLACES ORANY OTHER ITEMS
AROUND A CHILD'S NECK OR ON THE PRODUCT PARTS.
BEFORE EACH USAGE OR ASSEMBLY, INSPECT PRODUCT FOR
DAMAGED HARDWARE, LOOSE JOINTS, MISSING PARTS OR
SHARP EDGES. DO NOT USE PRODUCT IF ANY PARTS ARE
MISSING OR BROKEN. ASK YOUR DEALER OR WRITE TO DREAM
ON ME. FOR REPLACEMENT PARTS AND INSTRUCTIONAL
LITERATURE IF NEEDED. DO NOT SUBSTITUTE PARTS. THE
PRODUCT, INCLUDING SIDE RAILS,MUST BE FULLY ERECTED
PRIOR TO USE.
DISCONTINUE USE OF THE PRODUCT WHEN CHILD IS ABLE TO
CLIMB OUT REACHES THE HEIGHT OF 35 IN.(890MM).
WHEN CHILD IS ABLE TOPULL TO STANDING POSITION, REMOVE
BUMPER PADS. LARGE TOYS. AND OTHER OBJECTS THAT COULD
SERVE AS STEPS FOR CLIMBING OUT. WHEN CHILD IS ABLE TO
PULL TO STANDING POSITION, SET MATTRESS/BASE TO LOWEST
ADJUSTMENT POSITION AND REMOVE BUMPER PADS. LARGE
TOYS AND OTHER OBJECTS THAT COULD SERVE AS STEPS FOR
CLIMBING OUT.
DO NOT USE A WATER MATTRESS WITH THIS PRODUCT.
IF REFINISHING,USE ANONTOXIC FINISH SPECIFIED FOR
CHILDREN'S PRODUCTS.
ALWAYS PROVIDE THE SUPERVISION NECESSARY FOR THE
CONTINUED SAFETY OF YOUR CHILD.WHEN USED FOR PLAYING,
NEVER LEAVE CHILD UNATTENDED.
MADE IN CHINA

4
&
-

5
e. Wood Dowel 8 pcs
a. 3” Allen head Bolt 20 pcs
A. Top Rail (2PCS) B. Front Rail Bottom (1PC) C. Left Front
Leg (1PC)
G. Back Rail Bottom (1PC)
E. Left Back
Rail Leg (1PC)
J. Wooden mattress base (1PC)
CONNECTION HARDWARE
b. Barrel Nuts 20 pcs
c. 3/4” Allen head Bolt 4 pcs
d. Allen Wrench 1 pc
CRIB COMPONENTS
D. Right Front
Leg (1PC)
F. Right Back Rail Leg (1PC) H. Left Crib End (1PC)
I. Right Crib End (1PC) K. Mattress (1PC)
f. 1” Allen head Bolt 4 pcs
g. Metal connection 4 pcs
h. Nuts 4 pcs
WRENCH AND
PHILLIPS--HEAD SCREWDRIVER
REQUIRED FOR ASSEMBLY
----NOT INCLUDE
CLÉ À MOLETTE ET TOURNEVIS
À TËTE PLATE REQUIS POUR
L'ASSEMBLAGE (NON COMPRIS)

STEP 1
Insert wood dowels (e) into top rails (A).
A
e
e
STEP 2
I
F
D
Attach the right crib end (I) to the
right front leg (D) and the right
back leg (F) by using allen head
bolts (a) and barrel nuts (b) and
wood dowels (e). Then attach
the left crib end (H) to the left front
leg (C) and the left back leg (E) by
using allen head bolts (a) and
barrel nuts (b) and wood dowels(e).
e
e
a
aa
a
d
b
b
b
b
a
a
a
a
a
A
G
E
F
Attach the Top rail (A) and the
back rail bottom (G) to the left
back leg (E) by using allen
head bolts (a) and barrel nuts
(b) and wood dowel (e). Then
attach the Top rail (A) and the
back rail bottom (G) to the right
back leg (F) by using allen
head bolts (a) and barrel nuts
(b) and wood dowel (e)
e
e
b
b
b
4

7
STEP 4
c
c
J
E
C
D
F
STEP 5
a
a
Attach the Top rail (A) and the front
rail bottom (B) to the left front leg (C) by
using allen head bolts (a) and barrel nuts (b) and
wood dowel (e). Then attach the Top rail (A) and
the front rail bottom (B) to the right front leg (D) by
using allen head bolts (a) and barrel nuts (b) and
wood dowel (e).Last,Put the mattress (K) into the bed.
a
a
a
a
C
D
B
Ab
b
K
fg
h
Attach metal connection(g) to
the wooden mattress base(J)
by using bolts(f) and nuts(h) with wrench.
Position the wooden mattress
base(J) to a selected position
on legs.
thread insert on legs,then tighten
Insert the bolts(c) into
securely with Allen wrench(d).
Be sure the flat side of
wooden mattress base(J) is upward.

8
Remove the top rail (A) and the front rail bottom (B) as shown.
CONVERT THE CRIB INTO DAY BED
1.Remove the the Wooden mattress
base (J) .Then remove the right
crib end (I) and the left crib end (H).
2.Use the front panel as foot board
of the single bed.
3.Use the rear panel as head board
of the single bed.
4.connect the front and rear panels
by a standard hollywood frame
provided by others.
Converting crib to a twin bed I
(Hollywood bed frame sold separately)

9
Converting crib to a twin bed II
PA RTS REQUIRED TO COMPL ETE STEP
LEFT FOOT PLATFORM
POST x 1
NOT INCLUDED
POST x 1
NOT INCLUDED
RIGHT FOOT PLATFORM
POST x 1
NOT INCLUDED
RAIL
You have the option to convert crib to a twin bed II.
1:Use the back rail as the headboard of twin bed II.
3:Connect the assembled parts and headboard of twin bed to the kits ( legs, long rails,and
hardware ) which are not included and sold separately.
2:Connect the left foot platform and the right foot platform to the rail which are not included and
sold separately.
Model shown is example only.
Styles may vary .
(Hollywood bed frame sold separately)