Dream On Me 665 User manual

Adult assembly required.
Small parts may present choking hazard prior to assembly.
Enclosed are step by step instructions to help you.
quickly assemble your product.Before you begin we recommend
that you follow the steps below:
1. Please read the instructions thoroughly.
2. Identify all parts and hardware.
3. You will need the following tools:
Philips head screw driver
Flat head screw driver Hammer
Do Not Use Power Drills or Drivers
To protect parts during assembly please place them on a soft
surface.
To clean surface use only water on a damp cloth. Do not use
window cleaners or cleaning abrasives as it will scratch the surface
and could damage the protective coating.
ASSEMBLY INSTRUCTIONS
ITEM NO: 665
1
s
Read all instructions before assembling crib.
Save instructions for future use.
Dream On Me Inc.
1532 S WASHINGTON AVE
PISCATAWAY TWP NJ 08854
OFFICE: 732-752-7220
CUSTOMER SERVICE: 732-366-1788

2

.Read all instructions before assembling crib, keep instructions for future use.
.Upon completion of assembly be sure all screws, bolts and fastening devices have been
securely tightened. A frequent check should be made.
.Infants can suffocate in gaps between a mattress too small or too thick and product sides,
on soft bedding never add a mattress, pillow,comforter or padding.
.CAUTION: Any mattress used in this crib must be at least 27-1/4inches(690mm) by 51-5/8
inches(1310mm),with a thickness not exceeding 6 inches(150mm), the dimensions of the
.Failure to follow these warnings and instruction could result in serious injury or death.
.Never use plastic shipping bag or other plastic film as mattress covers not sold and
intended for that purpose, as they can cause suffocation .
.Strings can cause strangulation! Never place items with a string around a child’s neck,
.Never use this product if there are any loose or missing fasteners, loose joints,broken
parts, or torn mesh/fabric. check before assembly and periodically during use.
Contact DREAM ON ME for replacement parts and instructional literature if needed.
.Never substitute parts, the product including side rails, must be fully erected prior to use.
.Discontinue use of the product when child is able to climb out or reaches the height of
.When child is able to pull to standing position,set mattress/base to lowest adjustment
position and remove bumper pads, large toys,and other objects that could serve as steps
for climbing out. A child can trap parts of the body or clothing on loose fasteners .
.Never use a water mattress with this product.
.If refinishing,use a non-toxic finish specified for children’s products.
.To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their
back to sleep, unless otherwise advised by your physician.
WARNING !
.Never place product near window where cords from blinds or drapes can strangle a child.
MADE IN CHINA
35in (890mm).
mattress shall be taken from seam to seam or edge to edge where appropriate.
such as hood strings or pacifier cords. Never suspend strings over product or attach
strings to toys.
.Infants can suffocate on soft bedding .
.Never add a pillow or comforter .
.Never place additional padding under an infant .
.To help prevent strangulation tighten all fasteners.
.A child can trap parts of the body or clothing on loose fasteners.
.Follow warnings on all products in a crib .
See head panel & mattress support of the product for warnings.
Replace teething rail if damaged,cracked or loose.
3

=
4

5

6
CONNECTION HARDWARE
a : 1/4”x3” Allen head bolt (14 pcs)
e : 1/4”x2” Allen head bolt (16 pcs) f: 1/4”x3/4” Allen head bolt (4 pcs) g:Allen wrench (1pc)
b: Barrel nuts (14 pcs) c: Wood dowels (18 pcs) d: 1/4”x1-3/8” Allen head bolt (3 pcs)
PARTS ENCLOSED IN CARTON
ALeft head board
h:Washer (2pcs)
i:Screw (2pcs) j:Belt (1pc) k:Tip over restraints (1pc)
B
CRight changer side (1pc)
Left changer side (1pc) DChanger top bar (2pcs)
EChanger bottom bar (2pcs)
A
B
C
D
E
PHILLIPS--HEAD SCREWDRIVER
REQUIRED FOR ASSEMBLY
----NOT INCLUDE Do Not Use Power Drills or Drivers
D
E
14 pcs) 14 pcs)
16
2
m: 1/4”x4” Allen head bolt (2 pcs)
2pcs)
m4
EChanger bottom bar (4pcs)
E
E
1
1
2
2
1
2
2
4
2
n: 1/4”x2-3/8” Allen head bolt (2 pcs)
2
2-3/8
n
3/8”
e :

7
Metal spring support platform (1pc) Pad (1pc)
L
KM
FChanger shelf (1pcs)
The bottom bar(1pc)
GBack top rail (1pc) HBack bottom rail (1pc)
F
M
L
K
PBack right leg (1pc) QBack left leg (1pc)
GH
NFront rail (1pc)
N
GBack top rail (1pc) HBack bottom rail (1pc)
KLM
NPBack right leg (1pc) QBack left leg (1pc)
Changer shelf (2pcs)
1
F
1
1
F2
F2
F2
1
2

8
STEP 1
CRIB ASSEMBLY
STEP 2
2
B
D
D
E
e
e
e
e
c
c
c
c
c
c
c
c
P
1
E
1
E2
E2E2
E2
E1
E2
F1
F1
F2
F2
BD
D
E2
E1
E2
E2
E1
F1
D
F1
F2
F2
Use allen wrench(g) to connect bolts.
Connect changer longertop rail (D),
changer longermiddle rail 1(E1),
and changer longerbottom rail (E2)
to changer back leg (B1) and changer
front leg (B2) by using wood dowel (e1),
barrel nut (d) and 3”bolt (b).
e1
D
E1 E2

9
STEP 3
3
F
E
e
e
e
e
e
e
e
e
c
c
c
c
c
1
1
E2
F
2
F
2
c
D
D
C
c
CHANGER
To assemble part C to the assembled
part in Step 2 by using the same way
as step 1.
C
2
1

10
a
STEP 4
CRIB ASSEMBLY
H
b
b
a
a
a
a
a
a
ab
b
b
b
n
n
b
H
A
b
STEP 5
Attach Left head board (A)
to the back left leg (Q) using
Allen head bolt (n) and
barrel nuts (b).
Q
P
G
Q
G
P
To attach back bottom rail(H) and
back right leg(P) & back left leg(Q)
by using Allen head bolt (a).
To attach back top rail(G) and back
bottom rail(H) by using Allen head
bolt(a),(m).
5
m
m
4