Dream On Me Crib 663 User manual

1
STYLE NO: 663
DREAM ON ME INC.
125 HELEN STREET
S.PLAINFIELD NJ 07080
908-791-0555
Read all instructions before assembling crib.
Save instructions for future use.
Adult assembly required.
Small parts may present choking hazard prior to assembly.
Enclosed please find simple step-by-step instructions to help
you quickly assemble your products.Before you begin we
recommend that you following the steps below:
1.Please read the instructions thoroughly.
2. Identify all parts and hardwares
3.You will need the following tools:
Philips head screw driver
Flat head screw driver Hammer
Do Not Use Power Drills or Drivers
To protect your parts during assembly please place them on a
soft surface.
To clean surface use only water on a damp cloth. Do not use
window cleaners or cleaning abrasives as it will scratch the
surface and could damage the protective coating.
Please note that the warning sticker is placed on the cribs to keep parents and
caregivers informed it is a requirement by law under CPSC And ASTM.
We do apologize for any inconvenience this may cause you.

2
WARNING !
MADE IN CHINA
· FAILURE TO FOLLOW THESE WARNINGS AND THE ASSEMBLY INSTRUCTIONS
COULD RESULT IN SERIOUS INJURY OR DEATH.
· READ ALL INSTRUCTIONS BEFORE ASSEMBLING CRIB. KEEP INSTRUCTIONS
FOR FUTURE USE.
ANY MATTRESS USDED IN THIS CRIB MUST BE AT LEAST 51-5/8 INCHES BY
27-1/4 INCHES WITH A THICKNESS NOT EXCEEDING 6 INCHES.
· CHECK THIS PRODUCT FOR DAMAGED HARDWARE, LOOSE JOINTS, MISSING
PARTS OR SHARP EDGES BEFORE AND AFTER ASSEMBLY.A FREQUENT CHECK
DAMAGED OR BROKEN.CONTACT DREAM ON ME INC.125 HELEN STREET
S.PLAINFIELD NJ 07080
FOR REPLACEMENT PARTS AND INSTRUCTIONAL
LITERATURE IF NEEDED.DO NOT SUBSTITUTE PARTS.
· TO REDUCE THE RISK OF SIDS, PEDIATRICIANS RECOMMEND HEALTHY INFANTS
BE PLACED ON THEIR BACKS TO SLEEP, OTHERWISE ADVISED BY YOUR
PHYSICIAN.
· STRINGS CAN CAUSE STRANGULATION! DO NOT PLACE ITEMS WITH A STRING
AROUND A CHILD’S
NECK,SUCH AS HOOD STRINGS OR PACIFIER CORDS.
DO NOT SUSPEND STRINGS OVER A CRIB OR ATTACH A
STRINGS TO TOYS.
· TO HELP PREVENT STRANGULATION TIGHTEN ALL FASTENERS. A CHILD CAN
TRAP PARTS OF THE BODY OR CLOTHING ON LOOSE FASTENERS.
· DO NOT PLACE CRIB NEAR WINDOWS WHERE CORDS FROM BLINDS OR DRAPS
MAY STRANGLE A CHILD.
· WHEN CHILD IS ABLE TO PULL TO A STANDING POSITION, SET MATTRESS TO THE
LOWEST POSITION AND REMOVE BUMPER PADS, LARGE TOYS AND OTHER
OBJECTS THAT COULD SERVE AS STEPS FOR CLIMBING OUT.
· WHEN CHILD IS ABLE TO CLIMB OUT OR REACH THE HEIGHT OF 35 IN.(89CM),
THE CRIB SHALL NO LONGER BE USED.
· DO NOT USE A WATER MATTRESS WITH THIS CRIB.
· REPLACE TEETHING RAIL IF DAMAGED, CRACKED OR LOOSE.
· IF REFINISHING, USE A NON-TOXIC FINISH SPECIFIED FOR CHILDREN'S
PRODUCTS.
· NEVER USE PLASTIC SHIPPING BAGS OR OTHER PLASTIC FILM AS MATTRESS
COVERS BECAUSE THEY CAN CAUSE SUFFOCATION.
· INFANTS CAN SUFFOCATE IN GAPS BETWEEN CRIB SIDES AND A MATTRESS
THAT IS TOO SMALL.
· INFANTS CAN SUFFOCATE ON SOFT BEDDING,NEVER ADD A PILLOW OR
COMFORTER.NEVER PLACE ADDITIONAL PADDING UNDER AN INFANT.
· FOLLOW WARNINGS ON ALL PRODUCTS IN A CRIB. SEE HEAD PANNEL AND
MATTRESS SUPPORT FOR WARNINGS AND INSTRUCTIONS.
SHOULD BE MADE DURING USE.DO NOT USE CRIB IF ANY PARTS ARE MISSING,

3
CONNECTION HARDWARE
a: 1-5/8” Allen head
bolt (18 pcs)
b:Wood dowels (12pcs) c:Allen wrench (1pc) d:3” Allen head bolt (4pcs)
e:Barrel nuts (14 pcs) f: 3/4” Allen head bolt (4 pcs) h:1-1/5” Screw (3 pcs)
i:Knob (3pcs) j:Shelf support (8pcs)
PARTS ENCLOSED IN CARTON
A:Changer right side (1pc)
k:Washer (2pcs) l:Bolt (2pcs) m:Belt (1pc)
n:Tip over restraints (1pc)
B:Top rail (1pc)
C:Bottom bar (1pc)
Changer back Changer middle
E:Bottom bar (1pc)
D: Top bar (1pc)
B
C
D
E
g: 2-1/5”Allen head
bolt (10 pcs)
q:Bolt (1pc)
p:Cross screws (24pcs)
PHILLIPS--HEAD SCREWDRIVER
REQUIRED FOR ASSEMBLY
----NOT INCLUDE

4
R:Metal spring support platform (1pc)
Z:Smalll pad (1pc)
H
G
F
Changer front bar
F: Top (1pc)
G: Middle (1pc)
H:Bottom (1pc)
I:Changing surface (1pc)
J:Changer middle panel
K:Changer bottom shelf (1pc)
L:Changer left side (1pc) M:Left back leg (1pc)
N:Left board (1pc)
O:Left front leg (1pc)
Drawer T:Front panel (3pcs)
U:Left side panel (3pcs)
V: Right side panel (3pcs)
W:Back panel (3pcs)
X:Bottom panel (3pcs)
Q:Back rail bottom (1pc) S:Front rail bottom (1pc)
Y:Changer middle shelf (2pcs)
T
U
V
WX
P:Back top rail(1pcs)
αGuard rail (1pc)

5
CRIB ASSEMBLY
STEP 1
Attach The changer back(B&C) ,
and The changer middle(D&E) ,
and The changer front (F,G,&H)
toThe changer right side (A) using wood
dowels (b),
nuts(e) by allen
bolts (a),bolts (g) and barrel
wrench (c) .
Model shown is example only.
Styles may vary .
Lay down the assembled parts
on the floor .
Slide The changing surface (I)
into the groove in (D) along the
groove between (B) and (G) .
Slide (J) into the groove in (A)
along the groove between (D)
and (E) .
Then slide (K) into groove in
(A) along the groove between
(C) and (E) .
STEP 2
Model shown is example only.
Styles may vary .
g
e
a
A
B
C
D
H
F
I
J
K
B
C
E
A

6
STEP 3
Model shown is example only.
Styles may vary .
Attach The changer back (B&C) and
The changer middle (D&E) and The
changer front (F,G&H) to The
changer left side (L) using wood dowels
(b),bolts (a) and bolts (q) by allen
wrench (c) .
Attach left back leg (M) and
left front leg (O) to left board
(N) using bolts (d) and barrel
nuts (e) .
STEP 4
Model shown is example only.
Styles may vary .
b
b
qq
b
c
B
I
H
F
LJ
d
d
e
e
e
e

7
STEP 5
Model shown is example only.
Styles may vary .
Attach The top rail (P) and the
bottom rail (Q) to The changer
side (L) and left headboard
using wood dowels(b),bolts(q&g)
and barrel nuts(e) by allen wrench.
Locate the mattress support (R)
with tabs .
Be sure the smooth side of the
mattress support (R) is faced upward .
Position the tabs of the mattress
support(R) to mount to the selected
position in the legs .
Insert the bolts (f) , through the
tabs and into thread inserts ,
then tighten securely with allen
wrench (c) .
STEP 6
Model shown is example only.
Styles may vary .
f
M
e
e
b
b
g
g
M
L
R
g
g
e
g
q q
e
e

8
STEP 7
Model shown is example only.
Styles may vary .
STEP 8
Model shown is example only.
Styles may vary .
g
e
e
S
g
g
g
V
Attach The bottom front rail (S)
to The changer side (L) and
the left head board using
bolts (g),barrel nuts (e) and allen
wrench (c) .
Attach left side panel (U) & right side
panel (V) to back panel (W) by
inserting cross screw (p) into the holes
on left side panel (U) & right side panel
(V) .
p
p
p
p
DO NOT tighten all .

9
STEP 9
Model shown is example only.
Styles may vary .
Slide the bottom panel (X) painted side
up , into grooves of the left side panel
(U) and the right side panel (V) . In
the end , insert the bottom (X) into the
groove of back panel (W) .
Attach the front panel (T) to the left side
panel (U) and the right side panel (V)
by inserting cross screws (p) into the
holes on left side panel (U) & right side
panel (V) .
Inserting the bottom panel (X) into the
groove of the front panel (T) .
Tighten all the screws .
Assemble the rest two drawers follow step
8,9,10 .
STEP 10
Model shown is example only.
Styles may vary .
Attach the knob (i) to the front panel (T) by
screw (h) .
p
p
p
p
i
h
T
T
XU
V

10
STEP 11
Model shown is example only.
Styles may vary .
Insert the shelf supports (j) in the holes in the posts of changing table.
Then place the changer middle shelf (Y) inside the shelf support.
Tighten the screws in the shelf supports (j) .
j
j
j
j
j
j
Y
Y
PHILLIPS-- HEAD SCREWDRIVER REQUIRED
FOR ASSEMBLY- NOT INCLUDE