dreambaby ADHESIVE MAG LOCK F855 User manual

ADHESIVE
MAG LOCK®
Re-usable Template (clear plastic).
The installation template may not always be suitable for use on drawers.
PARTS
GREEN  ACTIVATED RED  DEACTIVATED
The Disengaging Feature will allow the Lock to be de-activated for extended periods of time.
To Use:
To open door place Key Dover Lock B.
To Remove:
Use rubber cement solvent, eucalyptus oil, or
similar type of product.
For added strength, install Catch Cand Lock Bwith
4g screws 2.85mm (
8 in) x 14mm ( 2 in) length -
pan head (screws not included)
IMPORTANT: Store Magnetic Key out of reach of children. The Key is a very powerful magnet so keep away from ELECTRICAL SOURCES, COMPUTERS, CELL PHONES, CREDIT CARDS etc.
WARNING: There is no substitute for proper adult supervision. This product is only a deterrent. Discontinue use when child is able to open it. All dangerous and toxic substances,
sharp edged or pointed objects, should always be kept “high up” or in a totally inaccessible area to children.
Keep instructions for future reference.
Dreambaby
®
products by
Look for the Dreambaby
®
range of Child Safety and Care Products.
Tee-Zed acknowledges that its customers may be entitled to statutory consumer guarantees and does not seek to exclude or limit them. These guarantees include that Tee-Zed’s products are of acceptable quality. This Tee-Zed product is for the specific purpose detailed
in the instructions and packaging and Tee-Zed considers use outside of that purpose to be abnormal use. To the maximum extent permitted by law, Tee-Zed does not accept any liability for damage:
• arising from abnormal use of the products;
• caused by installation or removal of the products other than in accordance with the supplied installation and removal instructions; or
• arising under the law of tort or contract.
Made in Dongguan, China.
©2018 Tee-Zed Products Pty Ltd
Tee-Zed Products Pty Ltd
PO Box 2022, Bondi Junction NSW 1355
Australia
 [phone]
 [e-mail]
www.dreambaby.com.au
Tee-Zed Products (N.Z.) Ltd
PO Box 64013, Botany Town Centre Auckland
New Zealand
 [phone]
 [e-mail]
www.dreambaby.co.nz
Tee-Zed Products Ltd
PO Box 29227, Dunfermline, KY12 2DN
United Kingdom
 [phone]
 [e-mail]
www.dreambaby.co.uk
X.02
PATENTED
F855 / F856 / F858 / F859
A
Lock
B
Catch
C
Key
D
A B C D
(not included in F858)

Installation steps - Read all steps before starting.
The Template A has been designed to help you install your Adhesive Mag Lock® in most cabinets.
It is recommended that, before any holes are drilled, you confirm the best place for your lock.
The installation template may not always be suitable for use on drawers.
Installation will depend on your cabinet and drawer construction, as possible mounting positions will vary from style to style.
Some cabinets have bumper pads, additional adjustments may be required when installing.
Installation
123 4
5678
910 11 12
• Decide on the best position for your
Adhesive MagLock®.
• Thoroughly clean and dry surfaces.
• Peel off the backing paper from
the Catch
C .
• Gently apply Catch
C into position
(do not press Catch firmly into place
at this stage).
• Peel the adhesive backing strip
from the Template
A .
• Peel off the backing paper from
foam tape on other side of
Template
A .
• Line up Template
A to catch with
foam adhesive facing out.
Press to stick Template
A to catch.
• Close door firmly and fully onto
the foam tape.
• This will transfer the Template
A
to the correct location on the
inside of doors or drawers.
• Disengage Lock
B by moving to
“red”position and peel off the
adhesive backing.
• Gently place the Lock B into
position using the Template
A
as a guide (do not press Lock
firmly into place at this stage).
• Remove the Template
A and
engage the Lock
B (green).
BEFORE CLOSING DOOR
Use Magnetic Key D to check
that the Lock B and Catch C
are aligned and working.
• If they are not catching, gently
peel away and reposition.
• When the Catch
C and
Lock
B align, apply firm
pressure to all parts.
• Disengage Lock
B (red) to allow entry
to cupboards while tape is setting.
• Leave for 48 hours to allow
adhesive to fully set.
!
!