Dreamline AQUA PLUS User manual

Rev 2.1 1
AQUA PLUS Shower / Tub Door Installation Manual
Important
Please read carefully the following instructions before installing your shower door. If you
have any questions on this shower door installation - please call our technical support
specialists Monday to Friday 9:00AM – 5:00PM EST at 1-866-731-8378 Option 3 or e-mail
our technical support group at [email protected]
Our product may have changes without prior notice

Rev 2.1 2
Preparation
1. After opening the boxes, read this introduction carefully, check all the packed parts are
complete by cross checking all the components against the “Detailed Diagram of
Shower Door Components”. Examine for shipping damage. If the unit has been
damaged or has a finishing defect, please contact your local distributor within 3
business days. Please note that Bath AuthorityTM / DreamLine TM will not replace any
damaged product or parts free of charge after 3 business days or if the product
has been installed. Contact your distributor or DreamLine if you have any questions.
2. Please note that you should consult your local building codes on questions on
installation compliance standards. Building and plumbing codes vary by location,
and DreamLine is not responsible for code compliance standards for your project.
3. Please ensure that prior to the installation the floor is leveled and solid. Also make sure
the walls are at right angles. While some adjustment in leveling of the door is possible,
irregular floor level or improper angle of side walls will result in serious problems for
your installation. Please note that there are some adjustments and drilling might be
necessary during the installation process.
Tools Required

Rev 2.1 3
Detailed Diagram of Shower Door Components
7
8
9
10
12
13
45
6
11
1
23
14
Packing List
01 Wall and glass profiles 1 set 08 Decorative plug 4pcs
02 Stationary glass 1pc 09 Countersunk screw ST 4.2×18 4pcs
03 Support bar 1pc 10 Round head screw ST 4.2×30 6pcs
04 Hinge 2pcs 11 Side strip 1pc
05 Glass door 1pc 12 Bottom anti-water strip 1pc
06 Handle 1pc 13 U-shape seal gasket 1pc
07 Wall anchor 5pcs 14 Screw inside Bottom bracket 1pc
After you have checked that all components are there, you will be ready to start the
installation of your DreamLine shower door.

Rev 2.1 4
Installation
1. Remove the Wall profile (01) (this is the external part of the wall and glass profiles set
with no holes along the surface side) and place it against the wall on the threshold in
the designated position. Note that this part of the profile piece should be fastened as
shown in Fig.1. Make sure it’s leveled and plumbed. Mark the drill holes on the wall.
Drill the holes, insert Wall Anchors (07) and attach the external profile wall profile to
the wall with the Screw ST4.2×30 (10). See Fig.1 for details.
2. a) Locate the Stationary glass panel (02) from the package and push the U-shape
seal gasket (13) onto the vertical edge of the stationary glass. Set the glass panel
onto the threshold, tray or bathtub, push it into the groove of the profile and then
snug it down with internal Glass Profile (01) with Countersunk screw ST 4.2×18
(09). See Fig.2 (Images 1-4) for details.
b) Take apart the Bottom bracket (14), place the mounting part into the U shape hole
of the Stationary glass panel (02) from inside and mark the drill hole on the
threshold, tray or bathtub. Remove the Stationary glass panel (02), drill the hole
and fix the Bottom bracket (14) with Round head screw ST4.2×30 (10). See Fig.2
(Images 5-8) for details.
3. Fasten the Stationary glass panel (02) in the wall profile. Assemble the Bottom
bracket (14), cover it with Decorative plug (08). See Fig.3 for details.
4. Locate the Support bar (03) from the package and loosen the glass holding screw on
the gliding channel. Place the Support bar with channel end on the glass top edge
and the bracket end flat on the wall. Adjust the bar to a proper position and level it
horizontally. Hold it firmly and outline the bracket’s position on the wall with a pencil.
Take off the Support bar and remove the bracket from it. Place the bracket against its
position on the wall and mark the drill hole. Drill the hole, insert the Wall anchor (07)
and attach the bracket onto the wall with the Screw ST4.2×30 (10). Replace the
Support bar with channel seated on the glass and the other end underneath the
bracket. Attach it to the bracket with the set-screw provided. Straighten the bar and
fasten both set screws and the glass holding screw to secure the glass. See Fig.4-5
for details.
5. Install the Hinges (04) on the stationary glass with the decorative non-screw side
facing outwards. Hook the Glass door (05) from inside. Make sure rubber gaskets are
used to prevent glass to metal connection. Perform necessary adjustment to have the
top edge of the door in line with that of the stationary glass. See Fig.6 for details.
6. a) Mount the Handle (06) onto the door. See Fig. 7 (Image 1) for details.
b) Push the Bottom anti-water strip (12) on the bottom edge of the glass door. See
Fig. 7 (Image 2) for details.
c) Measure the distance between the top edge of the glass door and upper edge of the
top hinge. Cut the piece off the Side strip (11) with a knife according to your
measurement. Repeat it to prepare the short strip for the hinge at the lower section of the
glass door. Then measure the distance between the bottom edge of the top hinge and
the upper edge of the bottom hinge and cut the rest of the strip to size. Open the door
and push all the strip lengths onto the vertical edge of the glass door. See Fig.7
(Image 3-4) for details.
7. Seal with caulk
(recommended 100% clear silicone) inside and outside along the bottom
of the stationary glass and between the wall and the wall profile. See Fig.8 for details.

Rev 2.1 5
Fig 1 Fig 2
Fig 3 Fig 4
6
1
2
3
4
1
2
3
4
5
7
8
Φ5/16”
2
1
6
5
4
3
2
1
Φ
5/16”
Φ1/8”

Rev 2.1 6
Fig 5 Fig 6
xxx
caulk
Fig 7 Fig 8
1
2
4
3
2
1

Rev 2.1 7
Maintenance
1. Tempered glass can be cleaned with nonabrasive bathroom cleaner or any glass
cleaner you use elsewhere in your home. Rinse off any glass cleaner that gets on
the metal parts as soon as possible to avoid damage to the metal surface. Avoid
striking it with any sharp or hard objects. Such damage can cause either immediate
or delayed breakage of tempered glass.
2. The metal parts in your shower door are durable and resistant to water damage. It is
advisable, but not necessary to wipe it with your towel after you shower. Clean it as
often as needed to keep the buildup off. Never use any type of abrasive cleaner. Use
only a soft damp cloth and nonabrasive bathroom cleaners.