Dreamline AQUALUX SHDR-3348588 Series User manual

Model#
SHDR-3348588-##
## finish
-01-Chrome
-04-Brushed Nickel
AQUALUX
Tub Door Installation Instructions
IMPORTANT
DreamLine® reserves the right to alter, modify or redesign products at any time without prior notice.
For the latest up-to-date technical drawings, manuals or additional details please refer to your model’s web
page on DreamLine.com
Please read these instructions carefully before installing. If you have any questions regarding installation, please
contact our technical support specialists Monday through Friday 8:00 AM – 7:00 PM EST at Phone:
1-866-731-2244, Fax: [phone] or e-mail our technical support group at [email protected]
For more information about DreamLine®Shower Doors & Tub Doors please visit DreamLine.com
Left Hand Installation shown

Preparation
1. Prior to installation, examine all boxes and packages for shipping damage and compare the piece
count with your packing slip. After opening all boxes and packages read this introduction carefully.
Check that all of the needed parts are included in the package by checking off the components on
the “Parts Diagram”. If the unit has been damaged, has a finishing defect, or has missing parts, please
contact our customer support department within 3 business days of the delivery date. Please note
that DreamLine®will not replace any damaged products or missing parts free of charge after
3 business days or if the product has been installed. Feel free to contact DreamLine®if you have
any questions, and please provide an order number, job name or other proof of purchase to help us
identify your original order.
2. Please note that you should consult your local building codes with questions on installation
compliance standards. Building and plumbing codes may vary by location, and DreamLine®is not
responsible for code compliance standards for your project and will not accept any returns.
3. If this unit is going to be installed in a new construction, please install all of the required plumbing
and drainage before installing the shower. Use a competent and licensed (if required by local
code) plumber for all plumbing installation.
4. Please make sure that prior to beginning the installation, the surfaces are leveled and solid and
will be able to support the total weight of the unit. Also make sure the walls are at right angles.
Irregular installation surface level, radius corners or improper angle of side walls will result in serious
problems for your installation. Please, note that some adjustments and drilling might be necessary
during the installation process.
5. Please protect all primary surfaces of the product during installation. Never set your glass down
directly onto a tile floor. Leave corner protectors in place until necessary to remove them. Always
use a piece of wood or cardboard to protect the bottom edge and corners of the glass prior to and
during installation.
6. This unit must be installed upon a finished threshold and against finished walls.
7. This model does NOT have any adjustment for out of plumb conditions. Verify that your walls are
plumb before proceeding with the installation.
8. This model requires that you drill into the threshold/tub surface for proper installation.
9. This model requires a minimum 3/4” of flat threshold space for installation.
10. This model is reversible for left or right hand installation. This manual will show the left hand
installation. For a right hand installation, simply begin on the opposite wall and reverse the
orientation of the parts as necessary.
NOTE: DO NOT install the handle onto the door glass until instructed to do so. DO NOT lift the
glass using the handle. This could result in damage to the glass and/or serious personal injury.
Always use an assistant or a professional grade glass suction cup when handling heavy glass.
2AQUALUX manual Ver 2 Rev 4 02/2016

Tools
NOTE: Unpack your unit carefully and inspect it. Lay it out and identify all parts using the detailed
diagram and packing list in this manual as a reference. Before discarding the carton, check for small
hardware bags that may have fallen to the bottom of the box. If any parts are damaged or missing,
please contact DreamLine® for replacement. The shipping boxes may contain extra parts not used in
your model configuration.
NOTE: Retain these installation instructions for future reference.
3AQUALUX manual Ver 2 Rev 4 02/2016
Tape
Measure
Screwdriver
Phillips (D=5/16") Drill bit
Level
Drill
Power Knife
(D=1/8")
Drill bit
Caulk
Hammer
Pencil

Parts diagram
4AQUALUX manual Ver 2 Rev 4 02/2016
01 Stationary glass 1pc
02 Support bar 1pc
03 Hinge 2pcs
04 Glass door 1pc
05 Handle 1pc
06 Wall Bracket
07 Wall Anchor 3pcs
2pcs
08 Round head screw ST4.2×55 2pcs
09 Flanged Side strip 1pc
10 Bottom anti-water strip
11 Bottom bracket 1pc
12 1pc
13
1pc
Round head screw ST4.2×30
1pcCountersunk screw ST4.2×40
7
8
10
9
6
11
12
13
1
2
34
5
Part # Description Qty Part # Description Qty

Installation steps
5AQUALUX manual Ver 2 Rev 4 02/2016
Fig 1
Fig 2
1
2
outside
1. Assemble the Wall brackets (06) onto the Stationary
glass (01). Use the at least one of the supplied gasskets
on each side to protect the glass.
See Fig 1 for details
2. Carefully place the Stationary glass (01) onto
tub surface. Position it against the wall and level it
vertically.
See Fig. 2 for details
Note: Use a level to make sure the Stationary glass
(01) is absolutely plumb.

6AQUALUX manual Ver 2 Rev 4 02/2016
Fig 3
Fig 4
12
34
56
Ø 5/16”
inside
outside
outside
3. Outline the position of the Wall brackets (06) on
the wall from inside of the shower area.
Set the Stationary glass (01) aside.
Remove the Wall brackets (06) from the Stationary
glass (01). Place the brackets back to the outlined
positions and mark holes for drilling.
Drill the holes in the wall using a Ø5/16” drill bit
and insert the Wall anchors (07). Fasten the Wall
brackets (06) to the wall using the Truss head
screw ST4.2×55 (08).
See Fig 3 for details
4. Place the Stationary glass (01) back onto
the tub surface against the Wall brackets
(06) and level it vertically.
Slide the Bottom bracket (11) into the notch
at the bottom of the Stationary glass (01).
See Fig 4 for details

7AQUALUX manual Ver 2 Rev 4 02/2016
Fig 5
Fig 6
12
34
1
2
Ø 1/8”
5. Mark the drilling hole on the threshold for the
Bottom bracket (11).
Set the Stationary glass (01) aside.
Drill a hole into the tub surface using an Ø1/8” drill
bit and fasten the Bottom bracket (11) to the tub
surface using the Truss head screw ST4.2×30 (12).
See Fig 5 for details
6. Place the Stationary glass (01) back into the
designated position on the tub. Make any final
adjustments, then re-assemble the Wall brackets
(06) and the Bottom bracket (11).
Install at least one gasket per side to protect the
glass from contact with the brackets.
See Fig 6 for details

8AQUALUX manual Ver 2 Rev 4 02/2016
1
2
Fig 7
Fig 8
56
7
123
Ø 5/16”
4
door
panel
inside
7. Locate the Support bar (02).
Position the Support bar (02) at an angle (ideally
45°) between the glass and the wall. Level it
horizontally. Hold it firmly and outline the bracket’s
position on the wall. Remove the Support bar (02)
and detach the wall bracket from it. Place the wall
bracket against its outlined position on the wall
and mark the drilling hole.
Drill a hole using a Ø 5/16” drill bit, insert the Wall
anchor (07) and fasten the wall bracket to the wall
with the Countersunk Screw ST4.2×40 (13).
Attach the Support bar (02) to the bracket as
shown in Fig. 7.5 and tighten the set screws and
the glass holding screw to secure the glass. Be sure
to install the gaskets to protect the glass.
See Fig 7 for details
8. Align the hinges with the edge of the glass and
attach the Hinges (03) to the Stationary glass (01)
with the decorative bolts facing inside the shower.
*Bring the Glass door (04) into the tub area and
align it with the Stationary glass (01).
Fasten the Hinges (03) onto the Glass door (04).
Make sure the top edges of the Glass door (04) and
the Stationary glass (01) are aligned.
See Fig 8 & 9 for details
*TIP: Use a 3/4” shim beneath the door glass to assist
with aligning the door glass with the installed hinges
and to maintain the proper spacing beneath the door
glass.
Note: Use the same combination of hinge gaskets on
both hinges for the inside and outside hinge plates.

9AQUALUX manual Ver 2 Rev 4 02/2016
inside
Fig 9
1
2
Fig 10
9. Install the Handle (05) onto the outside of the
Glass door (04) only. Make sure to use the supplied
gaskets and sleeves to protect the glass. Attach the
Bottom anti-water strip (10) over the bottom edge
of the Glass door (04).
See Fig 10 for details

10AQUALUX manual Ver 2 Rev 4 02/2016
Fig 11
Door
1”
1234
5678
Around Bottom sweep
measure
measure
10. Take three measurements:
• from the top edge of the Glass door (02) to the top of the center portion of the top Hinge (06)
(see Fig 11.1 for an example to use for all three measurements)
• from the bottom of the center portion of the top Hinge to the top of the center portion of the
bottom Hinge (06)
• from the bottom of the center portion of the bottom Hinge (06) to the threshold
Cut the Flanged side strip (09) according to the measurements.
Notch the cut strips to be able to slide them into the Hinges and around the installed Bottom
anti-water strip (10) to cover the space between both glass panels (Figs 11.2, 11.4, 11.6).
With the Glass door open, press the cut strips onto the vertical edge of the Glass door (02) as
shown.

11AQUALUX manual Ver 2 Rev 4 02/2016
24
Hours
Fig 12
11. Apply good quality mildew-resistant silicone along the connection of the stationary glass with
the wall and the tub surface.
Allow 24 hours for the silicone to fully cure before using the shower.
See Fig 13 for details

Product Maintenance
BASES and BACKWALLS: To ensure a long life for your acrylic back walls: wipe them off after
each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream
based cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or
dull the surface.
GLASS: To ensure long lasting life for your glass shower products: wipe them off after each use
with a soft cloth. Rinse and wipe off the glass using either a soft cloth or a squeegee to prevent
soap buildup and water spots. To prevent scratching the surface: never use abrasive cleaners
and cleaning products that contain scouring agents. Never use bristle brushes or abrasive
sponges.
HARDWARE: To ensure a long lasting finish: wipe off the metal parts after each use with a soft
cloth. Do not use abrasive cleaners or cleaning products containing ammonia, bleach or acid. If
accidentally used, rinse the surface as soon as possible to prevent finish peeling or corrosion.
After cleaning the shiny finishes, rinse thoroughly and wipe dry with soft cloth.
Never use an abrasive sponge or cloth, steel wool or wired brush as these may permanently
scratch the surface.
12AQUALUX manual Ver 2 Rev 4 02/2016

TEL: [phone]
FAX: [phone]
DREAMLINE.COM
For more information on DreamLine®Shower Doors and Enclosure please visit DreamLine.com