Drive Medical 13003 Installation guide

1. Remove contents from packaging and lay Table Top
(1) upside down on flat surface with Mounting Bracket
(5) facing upward. See Fig. 2.
2. Stand the Column Assembly (2) right side up as shown
in Fig. 1. Ensure Trip Rod (15) is visible in the rectan-
gular tube (as shown), but not protruding out of the
top. If necessary, shake the Column Assembly (2)
until the Trip Rod (15) drops into place inside the Col-
umn Assembly (2). Next, insert the Trip Lever (3), with
rounded side facing up, into the Column Assembly (2)
as shown, ensuring that the flat side of the Trip Lever
(3) rests on the Trip Rod. (15)
3. While holding the Trip Lever (3) securely in place on
top of the Trip Rod (15), flip the Column Assembly (2)
upside down and insert the Column Assembly (2) into
the table top Mounting Bracket (5) as shown in Fig. 2.
4. Align horizontal hole in table top Mounting Bracket
(5) with horizontal hole in Column Assembly (2) and
hole through Trip Lever (3). Insert / x 20 Bolt (4) into
horizontal hole & secure with Nut (4). Tighten with
10mm wrench. See Fig. 3.
5. Install two Domed Phillips Head bolts and locking
washers (6) through the vertical holes in the Mounting
Bracket (5) and into the threaded holes in Column As-
sembly (2) as shown in Fig. 4.
Assembly Instructions
Drive Medical
OVERBED TABLES - 13003/13067
6. Install two Casters With Lock (8) into Base (7) which
connects to Column Assembly (2). Install two
Non-Locking Casters (9) into base opposite Column
Assembly (2). See Fig. 5.
7. Install two Bolt Sleeves (10) into upside down Base (7)
and then position two Bolts (12) through Bolt Plate
(11) and into Bolt Sleeves (10). Position Base (7) over
Column Assembly (2) and thread bolts into boom of
Column Assembly (2) and tighten using 16mm wrench.
See Fig. 6.
8. Turn the table upright and stand on casters.
9. CAUTION: This step must be completed last to
prevent damage to the spring loaded mechanism.
Remove the Black Screw (13) in the Column Assembly
(2) collar labeled “Remove for Assembly” and replace
it with the Chrome Screw (14) contained in hardware
package. Do not remove Chrome Screw labeled “Do
Not Remove”. See Fig. 7 and Fig. 8.
FIG. 3
4
32
FIG. 2 1
25
FIG. 1
(15)
TRIP LEVER (3)
2
6
6
FIG. 4
2
5
FIG. 7
Remove 13
FIG. 8
Insert 14
CAUTION
FOR SAFETY – DO NOT REMOVE BLACK SCREW (13) ON COL-
UMN ASSEMBLY (2) UNTIL THE TABLE IS FULLY ASSEMBLED AND
STANDING IN UPRIGHT POSITION. AFTER REMOVING BLACK
SCREW, REPLACE WITH CHROME SCREW (14) INCLUDED IN
HARDWARE PACKAGE.
CAUTION
THE BOTTOM CHROME SCREW WITH THE “DO NOT REMOVE”
LABEL IS NEVER REMOVED AS IT WILL DAMAGE THE MECHANISM.
12
11
2
FIG. 6
10
1
7
8
9
FIG. 5
Column end of base
with 2 holes 7

Lifetime Limited Warranty
Your Drive branded product is warrantied to be free of
defects in materials and workmanship for the lifetime of
the product for the original consumer purchaser.
This device was built to exacting standards and care-
fully inspected prior to shipment. This Lifetime Limited
Warranty is an expression of our confidence in the materi-
als and workmanship of our products and our assurance to
the consumer of years of dependable service.
This warranty does not cover device failure due to owner
misuse or negligence, or normal wear and tear. The war-
ranty does not extend to non-durable components, such as
rubber accessories, casters, and grips, which are subject to
normal wear and need periodic replacement.
If you have a question about your Drive device or this war-
ranty, please contact an authorized Drive dealer.
© 2014 Medical Depot, Inc. All rights reserved.
Drive is a trademark of Medical Depot, Inc.
Port Washington N.Y. 11050 USA Made in China
Assembly Precautions
This Overbed Table utilizes a high-tension spring loaded mech-
anism to raise the table, DO NOT remove #13 Black Screw and
replace with #14 Chrome Screw until table is fully assembled.
DO NOT over tighten bolts, screws or use power tools when
assembling this product.
Important Warnings
Please follow all instructions and warnings to avoid hazardous
situations that can result in property damage and/or patient/
resident/staff/caregiver injury and/or death.
Inspect the product for damage and loose hardware before each
use. DO NOT use the product if it appears to be damaged or
unstable and DO NOT modify the product in any way.
Intended Use
This product is designed for use as a movable patient/resident
table top surface for reading, eating, or keeping small personal
items such as glasses, telephone, or books within easy reach.
This product is designed for indoor use ONLY within close prox-
imity of skilled caregivers. It is not designed to hold electrical
items (such as televisions, computer monitors, coffee pots, etc.)
and should not be used near open flames and excessive heat.
Maximum weight limitation for this product is 50 lbs (22 kg.);
weight should be evenly distributed over the table top surface
while at the lowest usable height to help maintain a stable con-
dition.
DO NOT overload the product as that could result in breakage,
as well as damage to property and/or serious injury.
Use ONLY as directed for its intended use. This product should
NOT be used: as a sleep surface; as a walker or mobility aid to
assist a person in walking, siing down or standing up; to prevent
or brace a person’s fall; or to help transport persons or items.
Parts List
1. Table Top
2. Column Assembly
3. Trip Lever
4. / - 20 x 2 /” Bolt & Nut
(1 each)
5. Mounting Bracket
(Top to Column Assembly)
6. / - 12 x /” Domed Phillips
Head Bolt & Lock Washer
(2each)
7. Base
8. Casters with Lock (2 each)
9. Casters without Lock
(2 each)
10. Bolt Sleeves (2 each)
11. Bolt Plate
12. / - 15 x 2” Bolts (2 each)
13. Black Screw
14. Chrome Screw (to
replace #13 black screw)
15. Trip Rod /” x 20 /”
(inside Column Assembly)
1. To raise top to desired height, apply light pressure
upward at any point under table.
2. To lower, squeeze trip lever (3) up towards top and
push down at column to desired height. Do not put
pressure on tabletop end that is opposite the column.
Column assembly will lock upon release of trip lever.
Operating Instructions
11
10
6124
14
4
3
6
HARDWARE