Drive inspired BCWL-7210S User manual

Wrap-Around Bath Support
Instructions
PVC frame with Padded Cushion
Model Numbers:
BCWL-7210S, BCWL-7310M, BCWL-7410L (Lo-Back)
BCWH-7610S, BCWH-7710M, BCWH-7910L (Hi-Back)
Lo-Back with Padding Hi-Back with Padding

Your Inspired by Drive Wrap-Around Bath Support has been built to the
highest standards of quality to ensure years of superior service. Please
take the time to read these instructions and pay particular attention to
the safety information provided.
Some additional precautions you can take to reduce the risk of injury:
1. Read and understand all instructions.
2. Determine, with a physician or therapist, the suitability of this
product for the intended user.
3. Never leave a user in the Wrap-Around Bath Support unattended in
the bath. The Wrap-Around Bath Support provides support but does
not replace adult supervision while bathing.
4. When this support is used in or around water, uninterrupted
supervision is necessary to reduce the risk of injury or drowning.
5. Regularly check that all locking knobs, buckles and other parts are
tight at all times.
6. Use the Wrap-Around Bath Support on level surfaces only.
If you require additional assistance, please call Columbia Customer
Service at [phone], or e-mail [e-mail]
Thank you for choosing Columbia.
Replacement Parts
Replacement parts can be ordered by calling our customer service
department at 800-454-6612, Monday – Friday, between 7:00 am and
5:00 pm PST/PDT. You can also order online at:
www.inspiredbydrive.com.
Other Uses
 The Wrap-Around Bath Support can be used indoors on the floor,
outdoors on the lawn, in a wading pool, or wherever a stable support
is desired.
 The Wrap-Around Bath Support disassembles easily for storage or for
traveling.
Cleaning Your Bath Support
The Bath Support may be cleaned with mild cleansers or soap. Harsh
abrasive cleaners may dull the finish. The metal parts of the bath
support are made of stainless steel and will not rust.
ATTENTION

Assembling the Wrap-Around Bath Support
Step 1: Attach the Legs
The front horizontal legs are shipped detached from the frame. To
assemble, depress the metal button on the legs and insert the legs into
the frame. The metal button will click into the holes of the frame, locking
the legs in place. See diagram below.
Step 2: Attach the Back Support
Place the metal plate which is attached to the back support against the
front side of the curved arch of the frame. Bolt the metal plate to the arch
by inserting the two bolts provided through the frame, from front to back.
Place the plastic washers on each bolt on the back side of the frame, then
screw on the plastic locking knobs. See diagram below.
Adjusting the Wrap-Around Bath Support
 Adjust the back height by loosening the plastic locking knobs and sliding
the back up or down on the metal plate to the desired height.
 Adjust the lap belt to provide a snug, but comfortable fit.
 If using a Hi-Back model, adjust the shoulder straps.
plastic
washers
plastic locking
knob
metal button
Exploded installation view of abductor (optional).
Use any of the pre-drilled holes in the flat plate
to position the abductor in the desired location.
To order abductor, please call Customer Service.
holes

11724 Willake Street
Santa Fe Springs, CA 90670
[phone]
Fax: [phone]
Email: [e-mail]
Website: www.inspriedbydrive.com
© 2017 Columbia Medical, LLC dba Inspired by Drive
Inspired by Drive warrants this product to be free of defects in
material and workmanship. Our obligation under this warranty is
limited to repair or replacement of any part or entire unit at our
option for a period of one year from date of delivery to the
original purchaser. The warranty does not include cost of
inconvenience, property damage, misuse, abuse, accident or
similar incidents. The warranty will not apply if product has been
tampered with or repaired by unauthorized individuals.
C0720-00-02 Jan 2017 (Rev F)