Drive KG P800 User manual

Kanga TS
pediatric frame
Item #
KG P800
KG 1000
KG 1200
KG 1400
www.drivemedical.com
EU Authorized Representative
Drive Medical LTD
Ainley’s Industrial Estate
Elland, West Yorkshire,
United Kingdom HX5 9JP
www.drivemedical.com

assembly
1. Open frame by pulling right and left side apart and
pushing down on the cross brace until fully extended.
2. Install right and left rear wheels by pushing the quick
release button (located in the center of the wheel)
on the axles and sliding it into the axle sleeve (A) until
it locks. To remove, push the quick release button and
pull out from axle sleeve.
3. Raise right and left back canes (B) until it clicks into
place.
4. Determine width of chair, 10” 12” or 14”. Remove
screws (circled below) and adjust cross brace
accordingly by pulling/pushing right and left side of
frame. Use 6mm allen wrench.
5. Loosen the rigidizer bar (C) by turning yellow knob
(D). Depress push pin (E) and adjust width accordingly.
B
A
C
EE
D
6. Bracket (below) needs to mounted towards the out
side for the 10” position. Remove allen screw on
front of back cane and reverse bracket. Use 4mm
allen wrench.
7. Reinstall screws from step 4.

folding
1. Raise armrests.
2. Turn yellow rigidizer bar knob (D) to loosen bar.
3. Lift levers (F) and fold canes?
4. Lift strap on top of cross bar and press the side
frames together.
F
F
adjustments
Seat Depth
Seat depth can be adjusted by removing rear wheels and
Allen screw (G) pushing/pulling seat rail to desired posi¬-
tion and returning Allen screw. Use 5mm allen wrench.
Additional 3” can be achieved by reversing the backrest
pivot plate (H)
Seat to Back Angle
Seat to back angle can be adjusted by loosening Allen
screw (J) on backrest pivot plate and moving the canes to
the desired position. Use 5mm allen wrench.
G
H
H
J

Armrests
Height can be adjusted by removing Allen screws (K) and
raising or lowering black bracket. Return Allen screws
and tighten. Angle can be adjusted by turning knob (L)
clockwise or counterclockwise. Use 5mm and 6mm allen
wrench.
K
L
Tilt-in-Space
Tilt can be achieved by pressing tilt-in-space release lever
(Q) and pushing down on both handles.
Push Handles
Height can be adjusted by loosening ratchet handle (M)
and raising or lowering to desired position.
Anti Tippers
Height can be adjusted by pulling on chrome disc (N) to
release anti tipper. Raise or lower to one of the five pre-
drilled holes.
N
installing original kanga seating components.
Five Point Harness:
Place shoulder straps over the top of back and fold over.
Insert screws through straps into back (O) and tighten.
Use 4mm allen wrench.
Fold crotch strap (P) under seat and insert screw thor-
ough the strap and into seat pan. Use 4mm allen wrench.
O
P
FRONT
BACK
M
M
Q

Headrest:
Mount headrest onto back by inserting screws through
plate and into back. Use 4mm allen wrench.
Laterals:
Mount laterals onto back by inserting screws through the
mounting plates and into back. Use 4mm allen wrench.
Pelvic straps:
The pelvic straps have Velcro on the bottom side. Mount
straps around frame as per diagram. .
Footrests:
Mount footrests hangars onto pins.

Abductor/Hip Guides.
Insert the hip guides directly into brackets that are
attached to the seat.
Seat & Back
Mount seat and then back by positioning grey frame clips
(circled below) on the seat rails and back canes and click-
ing them into place.
Heel & Toe Loops
The heel and toe loops get installed by inserting screw
through the front and back of the footplate and tighten-
ing the nut. Use 4mm allen wrench.
Harness
The flat metal plate on the front end of the pelvic straps
click into the bracket on the front end of the crotch strap.
To remove push the red button and pull on strap.
The clip on the end of the shoulder strap clicks onto the
bracket on the front end of the crotch strap.

Wipe aluminum parts with a clean, soft cloth at least once
a week. All metal parts can be cleaned with auto wax or
similar products. If exposed to moisture, dry immediately.
Do not use abrasive cleanser that will scratch the finish.
Tires should be cleaned occasionally with a damp cloth.
Replace if tires become severely worn or cracking
appears.
Front Wheels should be checked periodically and lubri-
cated occasionally. Lubricate by removing fork and greas-
ing caster stem bearings. Lubricate wheel bearings by
removing wheel from fork. Reassemble fork and wheel by
tightening nuts until no play remains, but wheels roll free-
ly. If nut is too loose, wheel will shimmy, if too tight, chair
will be hard to steer.
Rear Wheels should be inspected at least once a month
and make sure it spins freely. To adjust the play, remove
the wheel and with a wrench on the axle nut and on the
flat end on the other side adjust the length of the axle
until the wheel has the least amount of side play when
the plunger pops out.
Wheelchair is designed to be safe and stable as long as
center of gravity is maintained while going about normal
activities. Care must be taken while performing activities
that shift your center of gravity in the chair. Never reach
so far that it requires you to shift in the seat or bend over
out of the chair. When you have to reach for objects that
require you to lean, be certain front wheels are pointing
in a forward position that extends the wheel base and will
stabilize the chair.
general care
warning
Abductor:
Abductor fits into receiving tube under seat. Pull on
spring loaded knob and insert abductor;
FRONT
BACK
Place four aluminum black seats and back brackets
(circled below) over frame and fasten with knobs
provided.

warning
Do not attempt to operate on inclines or ramps 10° or
greater without proper assistance. If you must stop on an
incline, avoid sudden abrupt movement when you resume
movement. Because of backward angle of the chair, sud-
den abrupt movement could cause instability. Attempting
to use the wheel lock brakes could result in accidental
locking, tipping to one side, or cause a sudden stop.
Avoid changing direction when going down an incline, as
this could result in instability or tipping over.
Do not operate this wheelchair on roadways, streets or
any surfaces with vehicular traffic.
Be sure to completely engage wheel locks when getting in
and out of wheelchair or when in elevator or wheelchair
lift.
Do not adjust footrests any lower than 2.5” from floor.
When getting in or out of wheelchair, do not stand on or
apply weight to footrests.
Do not lean over or apply weight to the top of wheelchair
back. This can cause wheelchair to tip over. When trying
to extend arms over back, only reach as far as your arm
can extend without having to alter your seating position.
DO NOT stand on wheelchair.
Anti-tippers MUST BE attached at all times. Inasmuch as
the ANTI-TIPPERS are an option on this wheelchair (you
may order with or without the anti-tippers), Drive strongly
recommends ordering the anti-tippers as an additional
safeguard for the wheelchair user.
Your Drive brand product is warranted to be free
of defects in materials and workmanship for the
lifetime of the original consumer purchaser.
This device was built to exacting standards
and carefully inspected prior to shipment. This
Lifetime Limited Warranty is an expression of our
confidence in the materials and workmanship of
our products and our assurance to the consumer
of years of dependable service.
This warranty does not cover device failure
due to owner misuse or negligence, or normal
wear and tear. The warranty does not extend to
non-durable components, such as rubber
accessories, casters, and grips, which are subject
to normal wear and need periodic replacement.
If you have a question about your Drive device or
this warranty, please contact an authorized Drive
dealer.
limited lifetime
warranty
© 2012 Medical Depot, Inc. All rights reserved.
Drive is a trademark of Medical Depot, Inc.
Port Washington N.Y. 11050 USA Made in China